hyperion.ng/assets/firmware/arduino/adalight_mega_pwm/hyperion_mega.ino

251 lines
7.8 KiB
Arduino
Raw Normal View History

#include "FastLED.h"
#define ANALOG_MODE_AVERAGE 0
#define ANALOG_MODE_LAST_LED 1
/**************************************
S E T U P
set following values to your needs
**************************************/
// Number of leds in your strip. set to 1 and ANALOG_OUTPUT_ENABLED to true to activate analog only
#define NUM_LEDS 100
#define LED_TYPE WS2812B // type of your led controller, possible values, see below
// 3 wire (pwm): NEOPIXEL BTM1829 TM1812 TM1809 TM1804 TM1803 UCS1903 UCS1903B UCS1904 UCS2903 WS2812 WS2852
// S2812B SK6812 SK6822 APA106 PL9823 WS2811 WS2813 APA104 WS2811_40 GW6205 GW6205_40 LPD1886 LPD1886_8BIT
// 4 wire (spi): LPD8806 WS2801 WS2803 SM16716 P9813 APA102 SK9822 DOTSTAR
// For 3 wire led stripes line Neopixel/Ws2812, which have a data line, ground, and power, you just need to define DATA_PIN.
// For led chipsets that are SPI based (four wires - data, clock, ground, and power), both defines DATA_PIN and CLOCK_PIN are needed
// DATA_PIN, or DATA_PIN, CLOCK_PIN
#define LED_PINS MOSI // 3 wire leds
//#define LED_PINS MOSI, SCK // 4 wire leds
#define COLOR_ORDER GRB // colororder of the stripe, set RGB in hyperion
#define OFF_TIMEOUT 15000 // ms to switch off after no data was received, set 0 to deactivate
// analog rgb uni color led stripe - using of hyperion smoothing is recommended
#define ANALOG_MODE ANALOG_MODE_LAST_LED // use ANALOG_MODE_AVERAGE or ANALOG_MODE_LAST_LED
// overall color adjustments
#define ANALOG_BRIGHTNESS_RED 255 // maximum brightness for analog 0-255
#define ANALOG_BRIGHTNESS_GREEN 255 // maximum brightness for analog 0-255
#define ANALOG_BRIGHTNESS_BLUE 255 // maximum brightness for analog 0-255
#define BRIGHTNESS 128 // maximum brightness 0-255
#define DITHER_MODE BINARY_DITHER // BINARY_DITHER or DISABLE_DITHER
#define COLOR_TEMPERATURE CRGB(255,255,255) // RGB value describing the color temperature
#define COLOR_CORRECTION TypicalLEDStrip // predefined fastled color correction
//#define COLOR_CORRECTION CRGB(255,255,255) // or RGB value describing the color correction
// Baudrate, higher rate allows faster refresh rate and more LEDs (defined in /etc/boblight.conf)
#define serialRate 115200 // use 115200 for ftdi based boards
//#define serialRate 460800 // use 115200 for ftdi based boards
// ATTENTION this pin config is default for atmega328 based arduinos, others might work to
// if you have flickering analog leds this might be caused by unsynced pwm signals
// try other pins is more or less the only thing that helps
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
// 2 3 4 5 6 7 8 9 10 11 12 13 44 45 46
// R B G R B G R B G R B G R B G
#define ANALOG_PINS_MAX 15
#define ANALOG_RGB_STRIPES 4
const byte ANALOG_PINS[ANALOG_PINS_MAX] = {2,4,3,5,7,6,8,10,9,11,13,12,44,46,45};
#else
// 9 10 11
// R B G
#define ANALOG_PINS_MAX 3
#define ANALOG_RGB_STRIPES 1
const byte ANALOG_PINS[ANALOG_PINS_MAX] = {9,11,10};
#endif
/**************************************
A D A L I G H T C O D E
no user changes needed
**************************************/
// Adalight sends a "Magic Word" (defined in /etc/boblight.conf) before sending the pixel data
uint8_t prefix[] = {'A', 'd', 'a'}, hi, lo, chk, i;
unsigned long endTime;
// Define the array of leds
CRGB leds[NUM_LEDS];
// set rgb to analog led stripe
void showAnalogRGB(const CRGB& led, const short stripeId=-1) {
if (ANALOG_RGB_STRIPES > 0) {
byte r = map(led.r, 0,255,0,ANALOG_BRIGHTNESS_RED);
byte g = map(led.g, 0,255,0,ANALOG_BRIGHTNESS_GREEN);
byte b = map(led.b, 0,255,0,ANALOG_BRIGHTNESS_BLUE);
if (stripeId<0) {
for (byte i=0;i<ANALOG_RGB_STRIPES;i++) {
analogWrite(ANALOG_PINS[3*i+1], r);
analogWrite(ANALOG_PINS[3*i] , g);
analogWrite(ANALOG_PINS[3*i+2], b);
}
} else {
analogWrite(ANALOG_PINS[stripeId*3] , g);
analogWrite(ANALOG_PINS[stripeId*3+1], r);
analogWrite(ANALOG_PINS[stripeId*3+2], b);
}
}
}
// set color to all leds
void showColor(const CRGB& led) {
#if NUM_LEDS > ANALOG_RGB_STRIPES
LEDS.showColor(led);
#endif
showAnalogRGB(led);
}
// function to check if serial data is available
// if timeout occured leds switch of, if configured
bool checkIncommingData() {
boolean dataAvailable = true;
while (!Serial.available()) {
if ( OFF_TIMEOUT > 0 && endTime < millis()) {
showColor(CRGB(0,0,0)); // leds off
dataAvailable = false;
endTime = millis() + OFF_TIMEOUT;
}
}
return dataAvailable;
}
// main function that setups and runs the code
void setup() {
// analog output
if (ANALOG_RGB_STRIPES > 0) {
for (byte i=0;i<ANALOG_PINS_MAX;i++) {
pinMode(ANALOG_PINS[i], OUTPUT);
}
}
// Uncomment/edit one of the following lines for your leds arrangement.
int ledCount = NUM_LEDS;
if (ANALOG_MODE == ANALOG_MODE_LAST_LED) {
ledCount -= ANALOG_RGB_STRIPES;
}
#if NUM_LEDS > ANALOG_RGB_STRIPES
FastLED.addLeds<LED_TYPE, LED_PINS, COLOR_ORDER>(leds, ledCount);
#endif
// color adjustments
FastLED.setBrightness ( BRIGHTNESS );
FastLED.setTemperature( COLOR_TEMPERATURE );
FastLED.setCorrection ( COLOR_CORRECTION );
FastLED.setDither ( DITHER_MODE );
// initial RGB flash
showColor(CRGB(255, 0, 0)); delay(400);
showColor(CRGB(0, 255, 0)); delay(400);
showColor(CRGB(0, 0, 255)); delay(400);
showColor(CRGB(0, 0, 0));
Serial.begin(serialRate);
while (!Serial) {
; // wait for serial port to connect. Needed for native USB
}
Serial.print("Ada\n"); // Send "Magic Word" string to host
boolean transmissionSuccess;
unsigned long sum_r, sum_g, sum_b;
// loop() is avoided as even that small bit of function overhead
// has a measurable impact on this code's overall throughput.
while (true) {
// wait for first byte of Magic Word
for (i = 0; i < sizeof prefix; ++i) {
// If next byte is not in Magic Word, the start over
if (!checkIncommingData() || prefix[i] != Serial.read()) {
i = 0;
}
}
// Hi, Lo, Checksum
if (!checkIncommingData()) continue;
hi = Serial.read();
if (!checkIncommingData()) continue;
lo = Serial.read();
if (!checkIncommingData()) continue;
chk = Serial.read();
// if checksum does not match go back to wait
if (chk != (hi ^ lo ^ 0x55)) continue;
memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
transmissionSuccess = true;
sum_r = 0;
sum_g = 0;
sum_b = 0;
// read the transmission data and set LED values
for (uint8_t idx = 0; idx < NUM_LEDS; idx++) {
byte r, g, b;
if (!checkIncommingData()) {
transmissionSuccess = false;
break;
}
r = Serial.read();
if (!checkIncommingData()) {
transmissionSuccess = false;
break;
}
g = Serial.read();
if (!checkIncommingData()) {
transmissionSuccess = false;
break;
}
b = Serial.read();
leds[idx].r = r;
leds[idx].g = g;
leds[idx].b = b;
#if ANALOG_OUTPUT_ENABLED == true && ANALOG_MODE == ANALOG_MODE_AVERAGE
sum_r += r;
sum_g += g;
sum_b += b;
#endif
}
// shows new values
if (transmissionSuccess) {
endTime = millis() + OFF_TIMEOUT;
#if NUM_LEDS > ANALOG_RGB_STRIPES
FastLED.show();
#endif
#if ANALOG_RGB_STRIPES > 0
#if ANALOG_MODE == ANALOG_MODE_LAST_LED
for ( byte x=1; x<=ANALOG_RGB_STRIPES; x++) {
showAnalogRGB(leds[NUM_LEDS-x], x-1);
}
#else
showAnalogRGB(CRGB(sum_r/NUM_LEDS, sum_g/NUM_LEDS, sum_b/NUM_LEDS));
#endif
#endif
}
}
} // end of setup
void loop() {
// Not used. See note in setup() function.
}