Merge remote-tracking branch 'refs/remotes/hyperion-project/master' into weba

assets/firmware/arduino/adalight/adalight.ino

@@ -9,10 +9,11 @@
    set following values to your needs
  **************************************/
 
-#define INITAL_LED_TEST_ENABLED true
+#define INITIAL_LED_TEST_ENABLED true
+#define INITIAL_LED_TEST_BRIGHTNESS 32  // 0..255
 
 // Number of leds in your strip. set to "1" and ANALOG_OUTPUT_ENABLED to "true" to activate analog only
-#define NUM_LEDS 100
+#define MAX_LEDS 100
 
 // type of your led controller, possible values, see below
 #define LED_TYPE WS2812B 
@@ -54,8 +55,9 @@
 #define COLOR_CORRECTION  TypicalLEDStrip   // predefined fastled color correction
 //#define COLOR_CORRECTION  CRGB(255,255,255) // or RGB value describing the color correction
 
-// Baudrate, higher rate allows faster refresh rate and more LEDs (defined in /etc/boblight.conf)
+// Baudrate, higher rate allows faster refresh rate and more LEDs 
 #define serialRate 460800      // use 115200 for ftdi based boards
+//#define serialRate 115200      // use 115200 for ftdi based boards
 
 
 /**************************************
@@ -70,7 +72,7 @@ uint8_t prefix[] = {'A', 'd', 'a'}, hi, lo, chk, i;
 unsigned long endTime;
 
 // Define the array of leds
-CRGB leds[NUM_LEDS];
+CRGB leds[MAX_LEDS];
 
 // set rgb to analog led stripe
 void showAnalogRGB(const CRGB& led) {
@@ -86,7 +88,7 @@ void showAnalogRGB(const CRGB& led) {
 
 // set color to all leds
 void showColor(const CRGB& led) {
-  #if NUM_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
+  #if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
   LEDS.showColor(led);
   #endif
   showAnalogRGB(led);
@@ -94,8 +96,8 @@ void showColor(const CRGB& led) {
 
 // switch of digital and analog leds
 void switchOff() {
-  #if NUM_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
+  #if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
-  memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
+  memset(leds, 0, MAX_LEDS * sizeof(struct CRGB));
   FastLED.show();
   #endif
   showAnalogRGB(leds[0]);
@@ -118,25 +120,25 @@ bool checkIncommingData() {
 
 // main function that setups and runs the code
 void setup() {
-
+  Serial.begin(serialRate);
-  // additional ground pin to make wiring a bit easier
-  pinMode(ANALOG_GROUND_PIN, OUTPUT);
-  digitalWrite(ANALOG_GROUND_PIN, LOW);
 
   // analog output
   if (ANALOG_OUTPUT_ENABLED) {
+    // additional ground pin to make wiring a bit easier
+    pinMode(ANALOG_GROUND_PIN, OUTPUT);
+    digitalWrite(ANALOG_GROUND_PIN, LOW);
     pinMode(ANALOG_BLUE_PIN , OUTPUT);
     pinMode(ANALOG_RED_PIN  , OUTPUT);
     pinMode(ANALOG_GREEN_PIN, OUTPUT);
   }
 
   // Uncomment/edit one of the following lines for your leds arrangement.
-  int ledCount = NUM_LEDS;
+  int ledCount = MAX_LEDS;
   if (ANALOG_MODE == ANALOG_MODE_LAST_LED) {
     ledCount--;
   }
 
-  #if NUM_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
+  #if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
     FastLED.addLeds<LED_TYPE, LED_PINS, COLOR_ORDER>(leds, ledCount);
   #endif
   
@@ -147,14 +149,14 @@ void setup() {
   FastLED.setDither     ( DITHER_MODE );
 
   // initial RGB flash
-  #if INITAL_LED_TEST_ENABLED == true
+  #if INITIAL_LED_TEST_ENABLED == true
-  showColor(CRGB(255, 0, 0));  delay(400);
+  Serial.println("initial test");
-  showColor(CRGB(0, 255, 0));  delay(400);
+  showColor(CRGB(INITIAL_LED_TEST_BRIGHTNESS, 0, 0));  delay(400);
-  showColor(CRGB(0, 0, 255));  delay(400);
+  showColor(CRGB(0, INITIAL_LED_TEST_BRIGHTNESS, 0));  delay(400);
+  showColor(CRGB(0, 0, INITIAL_LED_TEST_BRIGHTNESS ));  delay(400);
   #endif
   showColor(CRGB(0, 0, 0));
 
-  Serial.begin(serialRate);
   Serial.print("Ada\n"); // Send "Magic Word" string to host
 
 
@@ -183,14 +185,16 @@ void setup() {
     // if checksum does not match go back to wait
     if (chk != (hi ^ lo ^ 0x55)) continue;
 
-    memset(leds, 0, NUM_LEDS * sizeof(struct CRGB));
+    memset(leds, 0, MAX_LEDS * sizeof(struct CRGB));
     transmissionSuccess = true;
     sum_r = 0;
     sum_g = 0;
     sum_b = 0;
 
+    int num_leds = (hi<<8) + lo + 1;
+
     // read the transmission data and set LED values
-    for (uint8_t idx = 0; idx < NUM_LEDS; idx++) {
+    for (uint8_t idx = 0; idx < min(num_leds,MAX_LEDS); idx++) {
       byte r, g, b;
       if (!checkIncommingData()) {
         transmissionSuccess = false;
@@ -220,22 +224,22 @@ void setup() {
     // shows new values
     if (transmissionSuccess) {
       endTime = millis() + OFF_TIMEOUT;
-      #if NUM_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
+      #if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
       FastLED.show();
       #endif
 
       #if ANALOG_OUTPUT_ENABLED == true
         #if ANALOG_MODE == ANALOG_MODE_LAST_LED
-          showAnalogRGB(leds[NUM_LEDS-1]);
+          showAnalogRGB(leds[MAX_LEDS-1]);
         #else
-          showAnalogRGB(CRGB(sum_r/NUM_LEDS, sum_g/NUM_LEDS, sum_b/NUM_LEDS));
+          showAnalogRGB(CRGB(sum_r/MAX_LEDS, sum_g/MAX_LEDS, sum_b/MAX_LEDS));
          #endif
       #endif
     }
   }
 } // end of setup
 
-
 void loop() {
   // Not used. See note in setup() function.
 }
+

assets/firmware/arduino/network_bridge/udpraw_serialadalight.py

@@ -0,0 +1,197 @@
+#!/usr/bin/env python
+#
+
+# Simple UDP to Serial redirector.
+# Author: https://github.com/penfold42
+
+# raw udp packets to raw serial:
+# python.exe udp_adalight.py -P 2801 COM4 115200
+
+# raw udp packets to adalight serial protocol:
+# python.exe udp_adalight.py -a -P 2801 COM4 115200
+
+# Derived from: https://github.com/pyserial/pyserial/blob/master/examples/tcp_serial_redirect.py
+#
+# (C) 2002-2016 Chris Liechti <cliechti@gmx.net>
+#
+# SPDX-License-Identifier:    BSD-3-Clause
+
+import sys
+import socket
+import serial
+import serial.threaded
+import time
+
+
+class SerialToNet(serial.threaded.Protocol):
+    """serial->socket"""
+
+    def __init__(self):
+        self.socket = None
+
+    def __call__(self):
+        return self
+
+    def data_received(self, data):
+        if self.socket is not None:
+            self.socket.sendall(data)
+
+
+if __name__ == '__main__':  # noqa
+    import argparse
+
+    parser = argparse.ArgumentParser(
+        description='Simple UDP to Serial redirector.',
+        epilog="""\
+NOTE: no security measures are implemented. Anyone can remotely connect
+to this service over the network.
+""")
+
+    parser.add_argument(
+        'SERIALPORT',
+        help="serial port name")
+
+    parser.add_argument(
+        'BAUDRATE',
+        type=int,
+        nargs='?',
+        help='set baud rate, default: %(default)s',
+        default=115200)
+
+    parser.add_argument(
+        '-q', '--quiet',
+        action='store_true',
+        help='suppress non error messages',
+        default=False)
+
+    parser.add_argument(
+        '-a', '--ada',
+        action='store_true',
+        help='prepend adalight header to serial packets',
+        default=False)
+
+    parser.add_argument(
+        '--develop',
+        action='store_true',
+        help='Development mode, prints Python internals on errors',
+        default=False)
+
+    group = parser.add_argument_group('serial port')
+
+    group.add_argument(
+        "--parity",
+        choices=['N', 'E', 'O', 'S', 'M'],
+        type=lambda c: c.upper(),
+        help="set parity, one of {N E O S M}, default: N",
+        default='N')
+
+    group.add_argument(
+        '--rtscts',
+        action='store_true',
+        help='enable RTS/CTS flow control (default off)',
+        default=False)
+
+    group.add_argument(
+        '--xonxoff',
+        action='store_true',
+        help='enable software flow control (default off)',
+        default=False)
+
+    group.add_argument(
+        '--rts',
+        type=int,
+        help='set initial RTS line state (possible values: 0, 1)',
+        default=None)
+
+    group.add_argument(
+        '--dtr',
+        type=int,
+        help='set initial DTR line state (possible values: 0, 1)',
+        default=None)
+
+    group = parser.add_argument_group('network settings')
+
+    exclusive_group = group.add_mutually_exclusive_group()
+
+    exclusive_group.add_argument(
+        '-P', '--localport',
+        type=int,
+        help='local UDP port',
+        default=2801)
+
+    args = parser.parse_args()
+
+    # connect to serial port
+    ser = serial.serial_for_url(args.SERIALPORT, do_not_open=True)
+    ser.baudrate = args.BAUDRATE
+    ser.parity = args.parity
+    ser.rtscts = args.rtscts
+    ser.xonxoff = args.xonxoff
+
+    if args.rts is not None:
+        ser.rts = args.rts
+
+    if args.dtr is not None:
+        ser.dtr = args.dtr
+
+    if not args.quiet:
+        sys.stderr.write(
+            '--- UDP to Serial redirector\n'
+            '--- listening on udp port {a.localport}\n'
+	    '--- sending to {p.name}  {p.baudrate},{p.bytesize}{p.parity}{p.stopbits}\n'
+            '--- type Ctrl-C / BREAK to quit\n'.format(p=ser, a=args))
+
+    try:
+        ser.open()
+    except serial.SerialException as e:
+        sys.stderr.write('Could not open serial port {}: {}\n'.format(ser.name, e))
+        sys.exit(1)
+
+    ser_to_net = SerialToNet()
+    serial_worker = serial.threaded.ReaderThread(ser, ser_to_net)
+    serial_worker.start()
+
+    srv = socket.socket(socket.AF_INET, socket.SOCK_DGRAM)
+    srv.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, 1)
+    srv.bind(('', args.localport))
+
+    try:
+        intentional_exit = False
+        while True:
+            try:
+                while True:
+                    try:
+                        data,addr = srv.recvfrom(1024)
+                        if not data:
+                            break
+
+			if args.ada:
+				numleds = len(data)/3
+				hi = (numleds-1)/256
+				lo = (numleds-1)&255
+				sum = hi^lo^0x55
+				ser.write ("Ada"+ chr(hi) + chr(lo) + chr(sum))
+
+                        ser.write(data)                 # get a bunch of bytes and send them
+                    except socket.error as msg:
+                        if args.develop:
+                            raise
+                        sys.stderr.write('ERROR: {}\n'.format(msg))
+                        # probably got disconnected
+                        break
+            except KeyboardInterrupt:
+                intentional_exit = True
+                raise
+            except socket.error as msg:
+                if args.develop:
+                    raise
+                sys.stderr.write('ERROR: {}\n'.format(msg))
+            finally:
+                ser_to_net.socket = None
+                sys.stderr.write('Disconnected\n')
+    except KeyboardInterrupt:
+        pass
+
+    sys.stderr.write('\n--- exit ---\n')
+    serial_worker.stop()
+

include/hyperion/Hyperion.h

@@ -70,7 +70,7 @@ public:
 	///
 	/// free all alocated objects, should be called only from constructor or before restarting hyperion
 	///
-	void freeObjects();
+	void freeObjects(bool emitCloseSignal=false);
 
 	static Hyperion* initInstance(const QJsonObject& qjsonConfig, const QString configFile);
 	static Hyperion* getInstance();
@@ -289,6 +289,7 @@ signals:
 
 	void imageToLedsMappingChanged(int mappingType);
 	void emitImage(int priority, const Image<ColorRgb> & image, const int timeout_ms);
+	void closing();
 
 private slots:
 	///

include/utils/jsonschema/QJsonFactory.h

@@ -21,8 +21,8 @@ public:
 	static int load(const QString& schema, const QString& config, QJsonObject& json)
 	{
 		// Load the schema and the config trees
-		QJsonObject schemaTree = readJson(schema);
+		QJsonObject schemaTree = readSchema(schema);
-		QJsonObject configTree = readJson(config);
+		QJsonObject configTree = readConfig(config);
 
 		// create the validator
 		QJsonSchemaChecker schemaChecker;
@@ -45,7 +45,7 @@ public:
 		return 0;
 	}
 	
-	static QJsonObject readJson(const QString& path)
+	static QJsonObject readConfig(const QString& path)
 	{
 		QFile file(path);
 		QJsonParseError error;
@@ -53,7 +53,7 @@ public:
 		if (!file.open(QIODevice::ReadOnly))
 		{
 			std::stringstream sstream;
-			sstream << "Configuration file not found: " << file.errorString().toStdString();
+			sstream << "Configuration file not found: '" << path.toStdString() << "' (" <<  file.errorString().toStdString() << ")";
 			throw std::runtime_error(sstream.str());
 		}
 
@@ -61,6 +61,7 @@ public:
 		config.remove(QRegularExpression("([^:]?\\/\\/.*)"));
 		
 		QJsonDocument doc = QJsonDocument::fromJson(config.toUtf8(), &error);
+		file.close();
 
 		if (error.error != QJsonParseError::NoError)
 		{
@@ -82,7 +83,45 @@ public:
 			throw std::runtime_error(sstream.str());
 		}
 
-		file.close();
+		return doc.object();
+	}
+
+	static QJsonObject readSchema(const QString& path)
+	{
+		QFile schemaData(path);
+		QJsonParseError error;
+
+		if (!schemaData.open(QIODevice::ReadOnly))
+		{
+			std::stringstream sstream;
+			sstream << "Schema not found: '" << path.toStdString() << "' (" <<  schemaData.errorString().toStdString() << ")";
+			throw std::runtime_error(sstream.str());
+		}
+
+		QByteArray schema = schemaData.readAll();
+		QJsonDocument doc = QJsonDocument::fromJson(schema, &error);
+		schemaData.close();
+		
+		if (error.error != QJsonParseError::NoError)
+		{
+			// report to the user the failure and their locations in the document.
+			int errorLine(0), errorColumn(0);
+
+			for( int i=0, count=qMin( error.offset,schema.size()); i<count; ++i )
+			{
+				++errorColumn;
+				if(schema.at(i) == '\n' )
+				{
+					errorColumn = 0;
+					++errorLine;
+				}
+			}
+
+			std::stringstream sstream;
+			sstream << "ERROR: Json schema wrong: " << error.errorString().toStdString() << " at Line: " << errorLine << ", Column: " << errorColumn;
+			throw std::runtime_error(sstream.str());
+		}
+
 		return doc.object();
 	}
 

include/utils/jsonschema/QJsonSchemaChecker.h

@@ -67,14 +67,6 @@ private:
 	///
 	void setMessage(const std::string & message);
 
-	///
-	/// Retrieves all references from the json-value as specified by the schema
-	///
-	/// @param[in] value The json-value
-	/// @param[in] schema The schema
-	///
-	void collectDependencies(const QJsonValue & value, const QJsonObject &schema);
-
 private:
 	// attribute check functions
 	///
@@ -106,15 +98,6 @@ private:
 	///
 	void checkAdditionalProperties(const QJsonObject & value, const QJsonValue & schema, const QStringList & ignoredProperties);
 
-	///
-	/// Checks if references are configued and used correctly. If this is not the case _error is set
-	/// to true and an error-message is added to the message-queue.
-	///
-	/// @param value The given json-object
-	/// @param schemaLink The schema of the json-object
-	///
-	void checkDependencies(const QJsonValue & value, const QJsonValue & schemaLink);
-
 	///
 	/// Checks if the given value is larger or equal to the specified value. If this is not the case
 	/// _error is set to true and an error-message is added to the message-queue.

libsrc/grabber/v4l2/V4L2Grabber.cpp

@@ -74,6 +74,7 @@ V4L2Grabber::~V4L2Grabber()
 
 void V4L2Grabber::uninit()
 {
+	Debug(_log,"uninit grabber: %s", _deviceName.c_str());
 	// stop if the grabber was not stopped
 	if (_initialized)
 	{

libsrc/hyperion/GrabberWrapper.cpp

@@ -27,6 +27,8 @@ GrabberWrapper::GrabberWrapper(std::string grabberName, const int priority, hype
 
 GrabberWrapper::~GrabberWrapper()
 {
+	stop();
+	Debug(_log,"Close grabber: %s", _grabberName.c_str());
 	delete _processor;
 }
 

libsrc/hyperion/Hyperion.cpp

@@ -447,8 +447,13 @@ Hyperion::Hyperion(const QJsonObject &qjsonConfig, const QString configFile)
 }
 
 
-void Hyperion::freeObjects()
+void Hyperion::freeObjects(bool emitCloseSignal)
 {
+	if (emitCloseSignal)
+	{
+		emit closing();
+	}
+
 	// switch off all leds
 	clearall();
 	_device->switchOff();
@@ -462,7 +467,7 @@ void Hyperion::freeObjects()
 
 Hyperion::~Hyperion()
 {
-	freeObjects();
+	freeObjects(false);
 }
 
 unsigned Hyperion::getLedCount() const

libsrc/jsonserver/JsonClientConnection.cpp

@@ -892,7 +892,7 @@ void JsonClientConnection::handleConfigCommand(const QJsonObject& message, const
 	}
 	else if (subcommand == "reload")
 	{
-		_hyperion->freeObjects();
+		_hyperion->freeObjects(true);
 		Process::restartHyperion();
 		sendErrorReply("failed to restart hyperion", full_command, tan);
 	} 
@@ -912,7 +912,7 @@ void JsonClientConnection::handleConfigGetCommand(const QJsonObject& message, co
 	
 	try
 	{
-		result["result"] = QJsonFactory::readJson(QString::fromStdString(_hyperion->getConfigFileName()));
+		result["result"] = QJsonFactory::readConfig(QString::fromStdString(_hyperion->getConfigFileName()));
 	}
 	catch(...)
 	{

libsrc/utils/jsonschema/QJsonSchemaChecker.cpp

@@ -115,6 +115,7 @@ void QJsonSchemaChecker::validate(const QJsonValue & value, const QJsonObject &s
 		else
 		{
 			// no check function defined for this attribute
+			_error = true;
 			setMessage(std::string("No check function defined for attribute ") + attribute.toStdString());
 			continue;
 		}

libsrc/webconfig/StaticFileServing.cpp

@@ -73,6 +73,13 @@ static inline void printErrorToReply (QtHttpReply * reply, QString errorMessage)
 	reply->appendRawData (errorMessage.toLocal8Bit ());
 }
 
+static inline void printError404ToReply (QtHttpReply * reply, QString errorMessage)
+{
+	reply->setStatusCode(QtHttpReply::NotFound);
+	reply->addHeader ("Content-Type", QByteArrayLiteral ("text/plain"));
+	reply->appendRawData (errorMessage.toLocal8Bit ());
+}
+
 void StaticFileServing::onRequestNeedsReply (QtHttpRequest * request, QtHttpReply * reply)
 {
 	QString command = request->getCommand ();
@@ -103,7 +110,7 @@ void StaticFileServing::onRequestNeedsReply (QtHttpRequest * request, QtHttpRepl
 		Q_INIT_RESOURCE(WebConfig);
 
 		QFileInfo info(_baseUrl % "/" % path);
-		if ( path == "/" || path.isEmpty() || ! info.exists() )
+		if ( path == "/" || path.isEmpty()  )
 		{
 			path = "index.html";
 		}
@@ -134,7 +141,7 @@ void StaticFileServing::onRequestNeedsReply (QtHttpRequest * request, QtHttpRepl
 		}
 		else
 		{
-			printErrorToReply (reply, "Requested file " % path % " couldn't be found !");
+			printError404ToReply (reply, "404 Not Found\n" % path % " couldn't be found !");
 		}
 	}
 	else

libsrc/webconfig/WebConfig.cpp

@@ -23,7 +23,7 @@ WebConfig::WebConfig(QObject * parent)
 		_baseUrl = webconfigConfig["document_root"].toString(_baseUrl);
 	}
 
-	if (_baseUrl != ":/webconfig")
+	if ( (_baseUrl != ":/webconfig") && !_baseUrl.trimmed().isEmpty())
 	{
 		QFileInfo info(_baseUrl);
 		if (!info.exists() || !info.isDir())
@@ -32,6 +32,8 @@ WebConfig::WebConfig(QObject * parent)
 			_baseUrl = WEBCONFIG_DEFAULT_PATH;
 		}
 	}
+	else
+		_baseUrl = WEBCONFIG_DEFAULT_PATH;
 
 	Debug(log, "WebUI initialized, document root: %s", _baseUrl.toUtf8().constData());
 	if ( webconfigEnable )

src/hyperiond/CMakeLists.txt

@@ -1,11 +1,18 @@
 
+SET(Hyperiond_QT_HEADERS
+	hyperiond.h
+)
+
+QT5_WRAP_CPP(Hyperiond_HEADERS_MOC ${Hyperiond_QT_HEADERS})
+
 add_executable(hyperiond 
+	${Hyperiond_QT_HEADERS}
+	${Hyperiond_HEADERS_MOC}
 	configMigratorBase.cpp
 	configMigratorBase.h
 	configMigrator.cpp
 	configMigrator.h
 	hyperiond.cpp
-	hyperiond.h
 	main.cpp
 )
 

src/hyperiond/hyperiond.cpp

@@ -79,6 +79,13 @@ HyperionDaemon::HyperionDaemon(QString configFile, QObject *parent)
 
 HyperionDaemon::~HyperionDaemon()
 {
+	freeObjects();
+	delete _hyperion;
+}
+
+void HyperionDaemon::freeObjects()
+{
+	Debug(_log, "destroy grabbers and network stuff");
 	delete _amlGrabber;
 	delete _dispmanx;
 	delete _fbGrabber;
@@ -92,8 +99,17 @@ HyperionDaemon::~HyperionDaemon()
 	delete _protoServer;
 	delete _boblightServer;
 	delete _udpListener;
-	delete _hyperion;
 
+	_v4l2Grabbers.clear();
+	_amlGrabber     = nullptr;
+	_dispmanx       = nullptr;
+	_fbGrabber      = nullptr;
+	_osxGrabber     = nullptr;
+	_kodiVideoChecker = nullptr;
+	_jsonServer     = nullptr;
+	_protoServer    = nullptr;
+	_boblightServer = nullptr;
+	_udpListener    = nullptr;
 }
 
 void HyperionDaemon::run()
@@ -113,56 +129,33 @@ void HyperionDaemon::run()
 	#endif
 	Info(_log, "Hyperion started");
 
-
+	connect(_hyperion,SIGNAL(closing()),this,SLOT(freeObjects()));
 }
 
 int HyperionDaemon::tryLoadConfig(const QString & configFile, const int schemaVersion)
 {
 	// make sure the resources are loaded (they may be left out after static linking)
 	Q_INIT_RESOURCE(resource);
-	QJsonParseError error;
 
 	// read the json schema from the resource
 	QString schemaFile = ":/hyperion-schema";
 	if (schemaVersion > 0)
 		schemaFile += "-" + QString::number(schemaVersion);
-	QFile schemaData(schemaFile);
+
-	if (!schemaData.open(QIODevice::ReadOnly))
+	QJsonObject schemaJson;
+	try
 	{
-		std::stringstream error;
+		schemaJson = QJsonFactory::readSchema(schemaFile);
-		error << "Schema not found or not supported: " << schemaData.errorString().toStdString();
-		throw std::runtime_error(error.str());
 	}
-	
+	catch(const std::runtime_error& error)
-	QByteArray schema = schemaData.readAll();
-	QJsonDocument schemaJson = QJsonDocument::fromJson(schema, &error);
-	schemaData.close();
-	
-	if (error.error != QJsonParseError::NoError)
 	{
-		// report to the user the failure and their locations in the document.
+		throw std::runtime_error(error.what());
-		int errorLine(0), errorColumn(0);
-		
-		for( int i=0, count=qMin( error.offset,schema.size()); i<count; ++i )
-		{
-			++errorColumn;
-			if(schema.at(i) == '\n' )
-			{
-				errorColumn = 0;
-				++errorLine;
-			}
-		}
-		
-		std::stringstream sstream;
-		sstream << "ERROR: Json schema wrong: " << error.errorString().toStdString() << " at Line: " << errorLine << ", Column: " << errorColumn;
-
-		throw std::runtime_error(sstream.str());
 	}
 
 	QJsonSchemaChecker schemaChecker;
-	schemaChecker.setSchema(schemaJson.object());
+	schemaChecker.setSchema(schemaJson);
 
-	_qconfig = QJsonFactory::readJson(configFile);
+	_qconfig = QJsonFactory::readConfig(configFile);
 	if (!schemaChecker.validate(_qconfig))
 	{
 		for (std::list<std::string>::const_iterator i = schemaChecker.getMessages().begin(); i != schemaChecker.getMessages().end(); ++i)
@@ -177,7 +170,6 @@ int HyperionDaemon::tryLoadConfig(const QString & configFile, const int schemaVe
 	return generalConfig["configVersion"].toInt(-1);
 }
 
-
 void HyperionDaemon::loadConfig(const QString & configFile, const int neededConfigVersion)
 {
 	Info(_log, "Selected configuration file: %s", configFile.toUtf8().constData());
@@ -472,7 +464,7 @@ void HyperionDaemon::createSystemFrameGrabber()
 			else if (type == "x11")      createGrabberX11(grabberConfig);
 			else { Warning( _log, "unknown framegrabber type '%s'", type.toUtf8().constData()); grabberCompState = false; }
 			
-			_hyperion->getComponentRegister().componentStateChanged(hyperion::COMP_GRABBER, grabberCompState);
+//			_hyperion->getComponentRegister().componentStateChanged(hyperion::COMP_GRABBER, grabberCompState);
 			_hyperion->setComponentState(hyperion::COMP_GRABBER, grabberCompState );
 		}
 	}

src/hyperiond/hyperiond.h

@@ -49,6 +49,7 @@
 
 class HyperionDaemon : public QObject
 {
+	Q_OBJECT
 public:
 	HyperionDaemon(QString configFile, QObject *parent=nullptr);
 	~HyperionDaemon();
@@ -65,6 +66,9 @@ public:
 	void createGrabberV4L2();
 	void createSystemFrameGrabber();
 
+public slots:
+	void freeObjects();
+
 private:
 	void createGrabberDispmanx();
 	void createGrabberAmlogic();

test/TestConfigFile.cpp

@@ -16,53 +16,30 @@ bool loadConfig(const QString & configFile)
 {
 	// make sure the resources are loaded (they may be left out after static linking)
 	Q_INIT_RESOURCE(resource);
-	QJsonParseError error;
 
 	////////////////////////////////////////////////////////////
 	// read and set the json schema from the resource
 	////////////////////////////////////////////////////////////
 
-	QFile schemaData(":/hyperion-schema-"+QString::number(CURRENT_CONFIG_VERSION));
+	QJsonObject schemaJson;
 	
-	if (!schemaData.open(QIODevice::ReadOnly))
+	try
 	{
-		std::stringstream error;
+		schemaJson = QJsonFactory::readSchema(":/hyperion-schema");
-		error << "Schema not found: " << schemaData.errorString().toStdString();
-		throw std::runtime_error(error.str());
 	}
-
+	catch(const std::runtime_error& error)
-	QByteArray schema = schemaData.readAll();
-	QJsonDocument schemaJson = QJsonDocument::fromJson(schema, &error);
-
-	if (error.error != QJsonParseError::NoError)
 	{
-		// report to the user the failure and their locations in the document.
+		throw std::runtime_error(error.what());
-		int errorLine(0), errorColumn(0);
-		
-		for( int i=0, count=qMin( error.offset,schema.size()); i<count; ++i )
-		{
-			++errorColumn;
-			if(schema.at(i) == '\n' )
-			{
-				errorColumn = 0;
-				++errorLine;
-			}
-		}
-		
-		std::stringstream sstream;
-		sstream << "Schema error: " << error.errorString().toStdString() << " at Line: " << errorLine << ", Column: " << errorColumn;
-
-		throw std::runtime_error(sstream.str());
 	}
 	
 	QJsonSchemaChecker schemaChecker;
-	schemaChecker.setSchema(schemaJson.object());
+	schemaChecker.setSchema(schemaJson);
 	
 	////////////////////////////////////////////////////////////
 	// read and validate the configuration file from the command line
 	////////////////////////////////////////////////////////////
 	
-	const QJsonObject jsonConfig = QJsonFactory::readJson(configFile);
+	const QJsonObject jsonConfig = QJsonFactory::readConfig(configFile);
 	
 	if (!schemaChecker.validate(jsonConfig))
 	{