* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
* This add a new device type - ws2812spi.
I've (ab)used the SPI interface to send the correct timing pulses to keep the ws2812 happy.
THE RATE IS IMPORTANT!
A FIXED CORE_CLK IS IMPORTANT!
Attach the SPI MOSI pin on the Pi to the DIN pin on your ws2812
"device" :
{
"name" : "MyPi",
"type" : "ws2812spi",
"colorOrder" : "grb",
"output" : "/dev/spidev0.0",
"rate" : 3800000
},
* updated hyperiond.test-binary
* Updated default SPI speed to the "correct" value.
My Pi was undervolted so was dropping the core clock confusing everything
* Code cleanups
explicitly set the final 3 bytes to 0
* Removed latchtime option - not applicable
* updated test binary
Former-commit-id: d3c19c8374999f7a554bb25ca181a8a483f86289
* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
* started bug fixes for APA strips with more physical leds than configured
* 1st cut of changes to APA102.
now looks at config for "leds" which is the # of hardware leds in the strip.
This enables us to write the correct trailer length in the packet.
Also fixed a bug where switchoff was writing the wrong # of leds
* removed commented out old code
removed debug printf
* included prebuild test binary for Pi2
* Second attempt at the fix.
BEFORE:
If you have more physcial LEDs than defined in the "leds" "index" section of the config there is random junk added to the end of the strip.
WITH THIS FIX:
In the "device" section specify the number of physical leds with:
"leds" : 212,
If this is greater than the number of led indexes, additional LEDs are set to black
If this is smaller than the number of led indexes, it is ignored
* included test binary
* Clean exit if the device config is missing or a non-supported device type is specified
Former-commit-id: 8ae96188fa74d91b13a921e7d5faf6d6ac1c42ee
* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
* Experimental changes to piblaster code to work how i think it should
It is now assumed that the PWM pins in groups of 3 correspond to RGB channels of the led.
"assignment" : "rgbrgbrgb",
Would result in:
//Channel number GPIO number Led channel
// 0 4 0 red
// 1 17 0 green
// 2 18 0 blue
// 4 27 1 red
// 5 21 1 green
// 6 22 1 blue
// 7 23 2 red
// 8 24 2 green
// 9 25 2 blue
* Ammend pwm channel mapping comments to match the code
* 1st cut of the new more flexible piblaster pin mapping support
it works but is still rough
* removed old "assignment" handling
- prints an error messaage if found and terminates
fixed the switchoff method
* removing iPins hard coded list of valid GPIO pins
* removed iPins array for switchOff function
* code cleanups
input validation
* Handle catching (and ignoring) SIGPIPE.
You can now kill and restart pi-blaster daemon and hyperiond will gracefully recover
* added a binary for testing
* Added sample config and my modified pi-blaster version to support more GPIOs
* moved hyperiond
* removed testing binaries
move sample configuration to the configs directory
* re enabled device config display
* removed sample configuration
Former-commit-id: 95e4d4ea2fb7cb5439e8cd597883a638da61a574
* Updated smoothing options for AtmoOrb, can now choose between Orb external or Hyperion's internal smoothing.
With skipSmoothingDif you can set the maximum allowed color difference before overriding / clearing Orb smoothing during faster color change like for instance color <-> black.
* Updated inline documentation.
* Fixed command type typo in AtmoOrb device.
* Corrected variable spelling in AtmoOrb device.
* Make smoothing also match equal values for AtmoOrb smoothing differential
Former-commit-id: 3eede43c2f76fa324f0144aeac0526b8125ad149
No functional changes, but
- files have been renamed
- the device name is now "file" not "test"
Former-commit-id: 3fbc03c3fe1d764654c1d28ebb80562ce6276ab1
2. Adds support for level shifters that invert the data
Config option - "invert" (integer)
if omitted, do not invert
if == 0, do not invert
if !=0, invert
Former-commit-id: fd5b2863a85b11ac3a8444d1e02822f852feb556
The RPi 2 and 3 have two PWM channels and 3 PWM pins available to the
gpio header. BCM18 and BCM12 run on PWM channel 0. BCM13 runs on PWM
channel 1. This change allows BCM13 to be used by allowing the PWM
channel to be specified.
Former-commit-id: 3693ab438c2b369e6307c262d32bba509409e5b9
