1
0
mirror of https://github.com/node-red/node-red-nodes.git synced 2023-10-10 13:36:58 +02:00
node-red-nodes/hardware/PiLiter/39-rpi-piliter.js
Dave C-J 48b0c3a68b Update Pi nodes to allow initial read / level set.
More consitent use of icons
Move to Raspberry Pi category
2014-10-27 20:28:05 +00:00

143 lines
4.2 KiB
JavaScript

/**
* Copyright 2014 IBM Corp.
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
**/
module.exports = function(RED) {
"use strict";
var exec = require('child_process').exec;
var fs = require('fs');
//if (!fs.existsSync("/dev/ttyAMA0")) { // unlikely if not on a Pi
//throw "Info : Ignoring Raspberry Pi specific node.";
//}
if (!fs.existsSync("/usr/local/bin/gpio")) { // gpio command not installed
throw "Info : Can't find Raspberry Pi wiringPi gpio command.";
}
// Map physical P1 pins to Gordon's Wiring-Pi Pins (as they should be V1/V2 tolerant)
var pintable = {
// Physical : WiringPi
"LED1":"7",
"LED2":"0",
"LED3":"2",
"LED4":"1",
"LED5":"3",
"LED6":"4",
"LED7":"5",
"LED8":"6"
}
var tablepin = {
// WiringPi : Physical
"0":"LED2",
"1":"LED4",
"2":"LED3",
"3":"LED5",
"4":"LED6",
"5":"LED7",
"6":"LED8",
"7":"LED1"
}
var barpins = {
"1":"128",
"2":"129",
"3":"133",
"4":"135",
"5":"143",
"6":"159",
"7":"191",
"8":"255",
}
var meterpins = {
"1":"128",
"2":"1",
"3":"4",
"4":"2",
"5":"8",
"6":"16",
"7":"32",
"8":"64",
}
function PiLiter(n) {
RED.nodes.createNode(this,n);
this.pin = pintable[n.pin];
this.pinv = n.pin;
var node = this;
//Set all pins to outputs
for (var p = 0; p < 8; p++) {
exec("gpio mode "+p+" out");
}
if (this.pinv === "bar") {
node.on("input", function(msg) {
var out = Number(msg.payload);
if ((out >= 1)&&(out <= 8)) { exec("gpio wb "+barpins[out]); }
else { exec("gpio wb 0"); }
});
}
else if (this.pinv === "meter") {
node.on("input", function(msg) {
var out = Number(msg.payload);
if ((out >= 1)&&(out <= 8)) { exec("gpio wb "+meterpins[out]); }
else { exec("gpio wb 0"); }
});
}
else if (this.pinv === "all") {
node.on("input", function(msg) {
var out = msg.payload;
if ((out === 1)|(out === true)|(out === "1")|(out === "on")) {
exec("gpio wb 255");
}
else { exec("gpio wb 0"); }
});
}
else if (this.pinv === "pin") {
node.on("input", function(msg) {
if (typeof msg.payload === "object") {
var out = Number(msg.payload.led);
var l = msg.payload.state;
if ((out >= 1)&&(out <= 8)) {
exec("gpio write "+pintable["LED"+out]+" "+l);
}
else { node.warn("Not a valid object - see Info panel."); }
}
else { node.warn("Not a valid object - see Info panel."); }
});
}
else {
node.on("input", function(msg) {
var out = Number(msg.payload);
if ((out >= 0)&&(out <= 255)) {
var val = 0;
for (var i = 0; i < 8; i ++) {
val += ((out & 0x01) << pintable["LED"+(i+1)]);
out = out >> 1;
}
exec("gpio wb "+val);
}
else { node.warn("Invalid input - not between 0 and 255"); }
});
}
node.on("close", function() {
exec("gpio wb 0");
});
}
RED.nodes.registerType("rpi-liter",PiLiter);
}