From db143ae9ca4cfffc58fdb5f787944afbc869e21f Mon Sep 17 00:00:00 2001 From: Bill Zimmerman Date: Tue, 11 Feb 2020 11:19:47 +0100 Subject: [PATCH] Updated FAQs (markdown) --- FAQs.md | 50 +------------------------------------------------- 1 file changed, 1 insertion(+), 49 deletions(-) diff --git a/FAQs.md b/FAQs.md index f749435..41cbaf9 100644 --- a/FAQs.md +++ b/FAQs.md @@ -97,55 +97,7 @@ Follow these steps in the order below: Please note: Pi-hole integration is not officially supported by this project. Therefore, bug reports will not be addressed. ### Can I configure RaspAP to work with a captive portal? -Yes, the [nodogsplash project](https://github.com/nodogsplash/nodogsplash) works just fine with RaspAP and is recommended over other methods. No configuration changes are needed with raspap-webgui, however you will need to modify some default settings in the nodogsplash config. - -The nodogsplash `GatewayInterface` should be set to the interface RaspAP runs on (`wlan0` is used by the Quick Installer). You will also need to change the `GateWayAddress` to `10.3.141.1`. - -` sudo nano /etc/nodogsplash/nodogsplash.conf` - -```# Parameter: GatewayInterface -# Default: NONE -# -# GatewayInterface is not autodetected, has no default, and must be set here. -# Set GatewayInterface to the interface on your router -# that is to be managed by Nodogsplash. -# Typically br-lan for the wired and wireless lan. -# -GatewayInterface wlan0 -``` - -``` -# Parameter: GatewayAddress -# Default: Discovered from GatewayInterface -# -# This should be autodetected on an OpenWRT system, but if not: -# Set GatewayAddress to the IP address of the router on -# the GatewayInterface. This is the address that the Nodogsplash -# server listens on. -# -GatewayAddress 10.3.141.1 -``` - -Give the nodogsplash service a kick: - -`sudo systemctl restart nodogsplash` - -and verify that the service is running: - -`sudo systemctl status nodogsplash` - -```● nodogsplash.service - NoDogSplash Captive Portal - Loaded: loaded (/lib/systemd/system/nodogsplash.service; enabled; vendor preset: enabled) - Active: active (running) since Sat 2019-03-02 07:55:11 UTC; 11min ago - Process: 3404 ExecStart=/usr/bin/nodogsplash -d 5 $OPTIONS (code=exited, status=0/SUCCESS) - Main PID: 3405 (nodogsplash) - CGroup: /system.slice/nodogsplash.service - └─3405 /usr/bin/nodogsplash -d 5 -``` - -Point your browser to http://10.3.141.1 and you should see the default nodogsplash page. - -![image](https://i.imgur.com/arTZmii.jpg) +Yes, the [nodogsplash project](https://github.com/nodogsplash/nodogsplash) works just fine with RaspAP and is recommended over other methods. A detailed setup guide is [available here](https://github.com/billz/raspap-webgui/wiki/Captive-portal-setup). ### Why can't I access wireless mode 'N' (802.11n)? On the **Configure hotspot** > **Security** tab, be sure to select CCMP for the Encryption Type. Save the settings and restart the hotspot. The wireless mode should be reported on clients as 802.11b/g/n.