satip-axe/kernel/arch/sh/boards/mach-mb519/setup.c

/*
 * arch/sh/boards/st/mb519/setup.c
 *
 * Copyright (C) 2007 STMicroelectronics Limited
 * Author: Stuart Menefy (stuart.menefy@st.com)
 *
 * May be copied or modified under the terms of the GNU General Public
 * License.  See linux/COPYING for more information.
 *
 * STMicroelectronics STx7200 Mboard support.
 */

#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/phy.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/stm/platform.h>
#include <linux/stm/stx7200.h>
#include <linux/irq.h>
#include <asm/irq-ilc.h>
#include <mach/epld.h>
#include <mach/common.h>



static void __init mb519_setup(char **cmdline_p)
{
	printk(KERN_NOTICE "STMicroelectronics STx7200 Mboard "
			"initialisation\n");

	stx7200_early_device_init();

	stx7200_configure_asc(2, &(struct stx7200_asc_config) {
			.hw_flow_control = 1,
			.is_console = 1, });
	stx7200_configure_asc(3, &(struct stx7200_asc_config) {
			.hw_flow_control = 1,
			.is_console = 0, });
}


static void mb519_mtd_set_vpp(struct map_info *map, int vpp)
{
	/* Bit 0: VPP enable
	 * Bit 1: Reset (not used in later EPLD versions) */

	if (vpp)
		epld_write(3, EPLD_FLASH);
	else
		epld_write(2, EPLD_FLASH);
}

static struct platform_device mb519_physmap_flash = {
	.name		= "physmap-flash",
	.id		= -1,
	.num_resources	= 1,
	.resource	= (struct resource[]) {
		STM_PLAT_RESOURCE_MEM(0, 32*1024*1024),
	},
	.dev.platform_data = &(struct physmap_flash_data) {
		.width		= 2,
		.set_vpp	= mb519_mtd_set_vpp,
	},
};

static struct stmmac_mdio_bus_data stmmac0_mdio_bus = {
	.bus_id = 0,
	.phy_mask = 0,
};

#define STMMAC1_PHY_ADDR 0
static int stmmac1_phy_irqs[PHY_MAX_ADDR] = {
		[STMMAC1_PHY_ADDR] = ILC_IRQ(95),
};
static struct stmmac_mdio_bus_data stmmac1_mdio_bus = {
	.bus_id = 1,
	.phy_mask = 0,
	.irqs = stmmac1_phy_irqs,
};

static struct platform_device mb519_epld_device = {
	.name		= "epld",
	.id		= -1,
	.num_resources	= 1,
	.resource	= (struct resource[]) {
		{
			.start	= EPLD_BASE,
			.end	= EPLD_BASE + EPLD_SIZE - 1,
			.flags	= IORESOURCE_MEM,
		}
	},
	.dev.platform_data = &(struct plat_epld_data) {
		.opsize = 16,
	},
};



static struct platform_device *mb519_devices[] __initdata = {
	&mb519_epld_device,
	&mb519_physmap_flash,
};


static int __init mb519_device_init(void)
{
	unsigned int epld_rev;
	unsigned int pcb_rev;

	epld_rev = epld_read(EPLD_EPLDVER);
	pcb_rev = epld_read(EPLD_PCBVER);
	printk(KERN_NOTICE "mb519 PCB rev %X EPLD rev %dr%d\n",
			pcb_rev, epld_rev >> 4, epld_rev & 0xf);

	stx7200_configure_ssc_i2c(0); /* HDMI */
	/* Usage of the remaining SSC is defined by the peripheral
	 * board (eg. MB520) */

	stx7200_configure_usb(0);
	stx7200_configure_usb(1);
	stx7200_configure_usb(2);

#if 1 /* On-board PHY (MII0) */
	stx7200_configure_ethernet(0, &(struct stx7200_ethernet_config) {
			.mode = stx7200_ethernet_mode_mii,
			.ext_clk = 1,
			.phy_bus = 0,
			.phy_addr = 0,
			.mdio_bus_data = &stmmac0_mdio_bus,
		});
#else /* External PHY board (MII1) */
	stx7200_configure_ethernet(1, &(struct stx7200_ethernet_config) {
			.mode = stx7200_ethernet_mode_mii,
			.ext_clk = 1,
			.phy_bus = 1,
			.phy_addr = STMMAC1_PHY_ADDR,
			.mdio_bus_data = &stmmac1_mdio_bus,
		});
#endif

	return platform_add_devices(mb519_devices, ARRAY_SIZE(mb519_devices));
}
arch_initcall(mb519_device_init);



static void __iomem *mb519_ioport_map(unsigned long port, unsigned int size)
{
	/* However picking somewhere safe isn't as easy as you might think.
	 * I used to use external ROM, but that can cause problems if you are
	 * in the middle of updating Flash. So I'm now using the processor
	 * core version register, which is guaranted to be available, and
	 * non-writable. */
	return (void __iomem *)CCN_PVR;
}

static void __init mb519_init_irq(void)
{
	epld_early_init(&mb519_epld_device);

	/* Mark Ethernet PHY as active low */
	set_irq_type(ILC_IRQ(93), IRQ_TYPE_LEVEL_LOW);
	set_irq_type(ILC_IRQ(95), IRQ_TYPE_LEVEL_LOW);

#if defined(CONFIG_SH_ST_STEM)
	/* The off chip interrupts on the mb519 are a mess. The external
	 * EPLD priority encodes them, but because they pass through the ILC3
	 * there is no way to decode them.
	 *
	 * So here we bodge it as well. Only enable the STEM INTR0 signal,
	 * and hope nothing else goes active. This will result in
	 * SYS_ITRQ[3..0] = 0100.
	 *
	 * BTW. According to EPLD code author - "masking" interrupts
	 * means "enabling" them... Just to let you know... ;-)
	 */
	epld_write(0xff, EPLD_INTMASK0CLR);
	epld_write(0xff, EPLD_INTMASK1CLR);
	/* IntPriority(4) <= not STEM_notINTR0 */
	epld_write(1 << 4, EPLD_INTMASK0SET);
#endif
}

struct sh_machine_vector mv_mb519 __initmv = {
	.mv_name		= "mb519",
	.mv_setup		= mb519_setup,
	.mv_nr_irqs		= NR_IRQS,
	.mv_init_irq		= mb519_init_irq,
	.mv_ioport_map		= mb519_ioport_map,
};