satip-axe/kernel/arch/avr32/boards/atstk1000/Kconfig

110 lines
2.7 KiB
Plaintext
Raw Normal View History

# STK1000 customization
if BOARD_ATSTK1000
choice
prompt "ATSTK1000 CPU daughterboard type"
default BOARD_ATSTK1002
config BOARD_ATSTK1002
bool "ATSTK1002"
select CPU_AT32AP7000
config BOARD_ATSTK1003
bool "ATSTK1003"
select CPU_AT32AP7001
config BOARD_ATSTK1004
bool "ATSTK1004"
select CPU_AT32AP7002
config BOARD_ATSTK1006
bool "ATSTK1006"
select CPU_AT32AP7000
endchoice
config BOARD_ATSTK100X_CUSTOM
bool "Non-default STK1002/STK1003/STK1004 jumper settings"
help
You will normally leave the jumpers on the CPU card at their
default settings. If you need to use certain peripherals,
you will need to change some of those jumpers.
if BOARD_ATSTK100X_CUSTOM
config BOARD_ATSTK100X_SW1_CUSTOM
bool "SW1: use SSC1 (not SPI0)"
help
This also prevents using the external DAC as an audio interface,
and means you can't initialize the on-board QVGA display.
config BOARD_ATSTK100X_SW2_CUSTOM
bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
help
If you change this you'll want an updated boot loader putting
the console on UART-C not UART-A.
config BOARD_ATSTK100X_SW3_CUSTOM
bool "SW3: use TIMER1 (not SSC0 and GCLK)"
help
This also prevents using the external DAC as an audio interface.
config BOARD_ATSTK100X_SW4_CUSTOM
bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
help
To use the camera interface you'll need a custom card (on the
PCI-format connector) connect a video sensor.
config BOARD_ATSTK1002_SW5_CUSTOM
bool "SW5: use MACB1 (not LCDC)"
depends on BOARD_ATSTK1002
config BOARD_ATSTK1002_SW6_CUSTOM
bool "SW6: more GPIOs (not MACB0)"
depends on BOARD_ATSTK1002
endif # custom
config BOARD_ATSTK100X_SPI1
bool "Configure SPI1 controller"
depends on !BOARD_ATSTK100X_SW4_CUSTOM
help
All the signals for the second SPI controller are available on
GPIO lines and accessed through the J1 jumper block. Say "y"
here to configure that SPI controller.
config BOARD_ATSTK1000_J2_LED
bool
default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
choice
prompt "LEDs connected to J2:"
depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
optional
help
Select this if you have jumpered the J2 jumper block to the
LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
IDC cable. A default "heartbeat" trigger is provided, but
you can of course override this.
config BOARD_ATSTK1000_J2_LED8
bool "LED0..LED7"
help
Select this if J2 is jumpered to LED0..LED7 amber leds.
config BOARD_ATSTK1000_J2_RGB
bool "RGB leds"
help
Select this if J2 is jumpered to the RGB leds.
endchoice
config BOARD_ATSTK1000_EXTDAC
bool
depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
default y
endif # stk 1000