110 lines
2.7 KiB
Plaintext
110 lines
2.7 KiB
Plaintext
|
# STK1000 customization
|
||
|
|
|
||
|
|
if BOARD_ATSTK1000
|
||
|
|
|
||
|
|
choice
|
||
|
|
prompt "ATSTK1000 CPU daughterboard type"
|
||
|
|
default BOARD_ATSTK1002
|
||
|
|
|
||
|
|
config BOARD_ATSTK1002
|
||
|
|
bool "ATSTK1002"
|
||
|
|
select CPU_AT32AP7000
|
||
|
|
|
||
|
|
config BOARD_ATSTK1003
|
||
|
|
bool "ATSTK1003"
|
||
|
|
select CPU_AT32AP7001
|
||
|
|
|
||
|
|
config BOARD_ATSTK1004
|
||
|
|
bool "ATSTK1004"
|
||
|
|
select CPU_AT32AP7002
|
||
|
|
|
||
|
|
config BOARD_ATSTK1006
|
||
|
|
bool "ATSTK1006"
|
||
|
|
select CPU_AT32AP7000
|
||
|
|
|
||
|
|
endchoice
|
||
|
|
|
||
|
|
|
||
|
|
config BOARD_ATSTK100X_CUSTOM
|
||
|
|
bool "Non-default STK1002/STK1003/STK1004 jumper settings"
|
||
|
|
help
|
||
|
|
You will normally leave the jumpers on the CPU card at their
|
||
|
|
default settings. If you need to use certain peripherals,
|
||
|
|
you will need to change some of those jumpers.
|
||
|
|
|
||
|
|
if BOARD_ATSTK100X_CUSTOM
|
||
|
|
|
||
|
|
config BOARD_ATSTK100X_SW1_CUSTOM
|
||
|
|
bool "SW1: use SSC1 (not SPI0)"
|
||
|
|
help
|
||
|
|
This also prevents using the external DAC as an audio interface,
|
||
|
|
and means you can't initialize the on-board QVGA display.
|
||
|
|
|
||
|
|
config BOARD_ATSTK100X_SW2_CUSTOM
|
||
|
|
bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
|
||
|
|
help
|
||
|
|
If you change this you'll want an updated boot loader putting
|
||
|
|
the console on UART-C not UART-A.
|
||
|
|
|
||
|
|
config BOARD_ATSTK100X_SW3_CUSTOM
|
||
|
|
bool "SW3: use TIMER1 (not SSC0 and GCLK)"
|
||
|
|
help
|
||
|
|
This also prevents using the external DAC as an audio interface.
|
||
|
|
|
||
|
|
config BOARD_ATSTK100X_SW4_CUSTOM
|
||
|
|
bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
|
||
|
|
help
|
||
|
|
To use the camera interface you'll need a custom card (on the
|
||
|
|
PCI-format connector) connect a video sensor.
|
||
|
|
|
||
|
|
config BOARD_ATSTK1002_SW5_CUSTOM
|
||
|
|
bool "SW5: use MACB1 (not LCDC)"
|
||
|
|
depends on BOARD_ATSTK1002
|
||
|
|
|
||
|
|
config BOARD_ATSTK1002_SW6_CUSTOM
|
||
|
|
bool "SW6: more GPIOs (not MACB0)"
|
||
|
|
depends on BOARD_ATSTK1002
|
||
|
|
|
||
|
|
endif # custom
|
||
|
|
|
||
|
|
config BOARD_ATSTK100X_SPI1
|
||
|
|
bool "Configure SPI1 controller"
|
||
|
|
depends on !BOARD_ATSTK100X_SW4_CUSTOM
|
||
|
|
help
|
||
|
|
All the signals for the second SPI controller are available on
|
||
|
|
GPIO lines and accessed through the J1 jumper block. Say "y"
|
||
|
|
here to configure that SPI controller.
|
||
|
|
|
||
|
|
config BOARD_ATSTK1000_J2_LED
|
||
|
|
bool
|
||
|
|
default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
|
||
|
|
|
||
|
|
choice
|
||
|
|
prompt "LEDs connected to J2:"
|
||
|
|
depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
|
||
|
|
optional
|
||
|
|
help
|
||
|
|
Select this if you have jumpered the J2 jumper block to the
|
||
|
|
LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
|
||
|
|
IDC cable. A default "heartbeat" trigger is provided, but
|
||
|
|
you can of course override this.
|
||
|
|
|
||
|
|
config BOARD_ATSTK1000_J2_LED8
|
||
|
|
bool "LED0..LED7"
|
||
|
|
help
|
||
|
|
Select this if J2 is jumpered to LED0..LED7 amber leds.
|
||
|
|
|
||
|
|
config BOARD_ATSTK1000_J2_RGB
|
||
|
|
bool "RGB leds"
|
||
|
|
help
|
||
|
|
Select this if J2 is jumpered to the RGB leds.
|
||
|
|
|
||
|
|
endchoice
|
||
|
|
|
||
|
|
config BOARD_ATSTK1000_EXTDAC
|
||
|
|
bool
|
||
|
|
depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
|
||
|
|
default y
|
||
|
|
|
||
|
|
endif # stk 1000
|