377 lines
8.3 KiB
C
377 lines
8.3 KiB
C
|
/*
|
||
|
|
* Hammerhead board-specific flash initialization
|
||
|
|
*
|
||
|
|
* Copyright (C) 2008 Miromico AG
|
||
|
|
*
|
||
|
|
* This program is free software; you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License version 2 as
|
||
|
|
* published by the Free Software Foundation.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include <linux/init.h>
|
||
|
|
#include <linux/platform_device.h>
|
||
|
|
#include <linux/mtd/mtd.h>
|
||
|
|
#include <linux/mtd/partitions.h>
|
||
|
|
#include <linux/mtd/physmap.h>
|
||
|
|
#include <linux/usb/isp116x.h>
|
||
|
|
#include <linux/dma-mapping.h>
|
||
|
|
#include <linux/delay.h>
|
||
|
|
|
||
|
|
#include <mach/portmux.h>
|
||
|
|
#include <mach/at32ap700x.h>
|
||
|
|
#include <mach/smc.h>
|
||
|
|
|
||
|
|
#include "../../mach-at32ap/clock.h"
|
||
|
|
#include "flash.h"
|
||
|
|
|
||
|
|
|
||
|
|
#define HAMMERHEAD_USB_PERIPH_GCLK0 0x40000000
|
||
|
|
#define HAMMERHEAD_USB_PERIPH_CS2 0x02000000
|
||
|
|
#define HAMMERHEAD_USB_PERIPH_EXTINT0 0x02000000
|
||
|
|
|
||
|
|
#define HAMMERHEAD_FPGA_PERIPH_MOSI 0x00000002
|
||
|
|
#define HAMMERHEAD_FPGA_PERIPH_SCK 0x00000020
|
||
|
|
#define HAMMERHEAD_FPGA_PERIPH_EXTINT3 0x10000000
|
||
|
|
|
||
|
|
static struct smc_timing flash_timing __initdata = {
|
||
|
|
.ncs_read_setup = 0,
|
||
|
|
.nrd_setup = 40,
|
||
|
|
.ncs_write_setup = 0,
|
||
|
|
.nwe_setup = 10,
|
||
|
|
|
||
|
|
.ncs_read_pulse = 80,
|
||
|
|
.nrd_pulse = 40,
|
||
|
|
.ncs_write_pulse = 65,
|
||
|
|
.nwe_pulse = 55,
|
||
|
|
|
||
|
|
.read_cycle = 120,
|
||
|
|
.write_cycle = 120,
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct smc_config flash_config __initdata = {
|
||
|
|
.bus_width = 2,
|
||
|
|
.nrd_controlled = 1,
|
||
|
|
.nwe_controlled = 1,
|
||
|
|
.byte_write = 1,
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct mtd_partition flash_parts[] = {
|
||
|
|
{
|
||
|
|
.name = "u-boot",
|
||
|
|
.offset = 0x00000000,
|
||
|
|
.size = 0x00020000, /* 128 KiB */
|
||
|
|
.mask_flags = MTD_WRITEABLE,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.name = "root",
|
||
|
|
.offset = 0x00020000,
|
||
|
|
.size = 0x007d0000,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.name = "env",
|
||
|
|
.offset = 0x007f0000,
|
||
|
|
.size = 0x00010000,
|
||
|
|
.mask_flags = MTD_WRITEABLE,
|
||
|
|
},
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct physmap_flash_data flash_data = {
|
||
|
|
.width = 2,
|
||
|
|
.nr_parts = ARRAY_SIZE(flash_parts),
|
||
|
|
.parts = flash_parts,
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct resource flash_resource = {
|
||
|
|
.start = 0x00000000,
|
||
|
|
.end = 0x007fffff,
|
||
|
|
.flags = IORESOURCE_MEM,
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct platform_device flash_device = {
|
||
|
|
.name = "physmap-flash",
|
||
|
|
.id = 0,
|
||
|
|
.resource = &flash_resource,
|
||
|
|
.num_resources = 1,
|
||
|
|
.dev = { .platform_data = &flash_data, },
|
||
|
|
};
|
||
|
|
|
||
|
|
#ifdef CONFIG_BOARD_HAMMERHEAD_USB
|
||
|
|
|
||
|
|
static struct smc_timing isp1160_timing __initdata = {
|
||
|
|
.ncs_read_setup = 75,
|
||
|
|
.nrd_setup = 75,
|
||
|
|
.ncs_write_setup = 75,
|
||
|
|
.nwe_setup = 75,
|
||
|
|
|
||
|
|
|
||
|
|
/* We use conservative timing settings, as the minimal settings aren't
|
||
|
|
stable. There may be room for tweaking. */
|
||
|
|
.ncs_read_pulse = 75, /* min. 33ns */
|
||
|
|
.nrd_pulse = 75, /* min. 33ns */
|
||
|
|
.ncs_write_pulse = 75, /* min. 26ns */
|
||
|
|
.nwe_pulse = 75, /* min. 26ns */
|
||
|
|
|
||
|
|
.read_cycle = 225, /* min. 143ns */
|
||
|
|
.write_cycle = 225, /* min. 136ns */
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct smc_config isp1160_config __initdata = {
|
||
|
|
.bus_width = 2,
|
||
|
|
.nrd_controlled = 1,
|
||
|
|
.nwe_controlled = 1,
|
||
|
|
.byte_write = 0,
|
||
|
|
};
|
||
|
|
|
||
|
|
/*
|
||
|
|
* The platform delay function is only used to enforce the strange
|
||
|
|
* read to write delay. This can not be configured in the SMC. All other
|
||
|
|
* timings are controlled by the SMC (see timings obove)
|
||
|
|
* So in isp116x-hcd.c we should comment out USE_PLATFORM_DELAY
|
||
|
|
*/
|
||
|
|
void isp116x_delay(struct device *dev, int delay)
|
||
|
|
{
|
||
|
|
if (delay > 150)
|
||
|
|
ndelay(delay - 150);
|
||
|
|
}
|
||
|
|
|
||
|
|
static struct isp116x_platform_data isp1160_data = {
|
||
|
|
.sel15Kres = 1, /* use internal downstream resistors */
|
||
|
|
.oc_enable = 0, /* external overcurrent detection */
|
||
|
|
.int_edge_triggered = 0, /* interrupt is level triggered */
|
||
|
|
.int_act_high = 0, /* interrupt is active low */
|
||
|
|
.delay = isp116x_delay, /* platform delay function */
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct resource isp1160_resource[] = {
|
||
|
|
{
|
||
|
|
.start = 0x08000000,
|
||
|
|
.end = 0x08000001,
|
||
|
|
.flags = IORESOURCE_MEM,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.start = 0x08000002,
|
||
|
|
.end = 0x08000003,
|
||
|
|
.flags = IORESOURCE_MEM,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.start = 64,
|
||
|
|
.flags = IORESOURCE_IRQ,
|
||
|
|
},
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct platform_device isp1160_device = {
|
||
|
|
.name = "isp116x-hcd",
|
||
|
|
.id = 0,
|
||
|
|
.resource = isp1160_resource,
|
||
|
|
.num_resources = 3,
|
||
|
|
.dev = {
|
||
|
|
.platform_data = &isp1160_data,
|
||
|
|
},
|
||
|
|
};
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef CONFIG_BOARD_HAMMERHEAD_USB
|
||
|
|
static int __init hammerhead_usbh_init(void)
|
||
|
|
{
|
||
|
|
struct clk *gclk;
|
||
|
|
struct clk *osc;
|
||
|
|
|
||
|
|
int ret;
|
||
|
|
|
||
|
|
/* setup smc for usbh */
|
||
|
|
smc_set_timing(&isp1160_config, &isp1160_timing);
|
||
|
|
ret = smc_set_configuration(2, &isp1160_config);
|
||
|
|
|
||
|
|
if (ret < 0) {
|
||
|
|
printk(KERN_ERR
|
||
|
|
"hammerhead: failed to set ISP1160 USBH timing\n");
|
||
|
|
return ret;
|
||
|
|
}
|
||
|
|
|
||
|
|
/* setup gclk0 to run from osc1 */
|
||
|
|
gclk = clk_get(NULL, "gclk0");
|
||
|
|
if (IS_ERR(gclk))
|
||
|
|
goto err_gclk;
|
||
|
|
|
||
|
|
osc = clk_get(NULL, "osc1");
|
||
|
|
if (IS_ERR(osc))
|
||
|
|
goto err_osc;
|
||
|
|
|
||
|
|
if (clk_set_parent(gclk, osc)) {
|
||
|
|
pr_debug("hammerhead: failed to set osc1 for USBH clock\n");
|
||
|
|
goto err_set_clk;
|
||
|
|
}
|
||
|
|
|
||
|
|
/* set clock to 6MHz */
|
||
|
|
clk_set_rate(gclk, 6000000);
|
||
|
|
|
||
|
|
/* and enable */
|
||
|
|
clk_enable(gclk);
|
||
|
|
|
||
|
|
/* select GCLK0 peripheral function */
|
||
|
|
at32_select_periph(GPIO_PIOA_BASE, HAMMERHEAD_USB_PERIPH_GCLK0,
|
||
|
|
GPIO_PERIPH_A, 0);
|
||
|
|
|
||
|
|
/* enable CS2 peripheral function */
|
||
|
|
at32_select_periph(GPIO_PIOE_BASE, HAMMERHEAD_USB_PERIPH_CS2,
|
||
|
|
GPIO_PERIPH_A, 0);
|
||
|
|
|
||
|
|
/* H_WAKEUP must be driven low */
|
||
|
|
at32_select_gpio(GPIO_PIN_PA(8), AT32_GPIOF_OUTPUT);
|
||
|
|
|
||
|
|
/* Select EXTINT0 for PB25 */
|
||
|
|
at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_USB_PERIPH_EXTINT0,
|
||
|
|
GPIO_PERIPH_A, 0);
|
||
|
|
|
||
|
|
/* register usbh device driver */
|
||
|
|
platform_device_register(&isp1160_device);
|
||
|
|
|
||
|
|
err_set_clk:
|
||
|
|
clk_put(osc);
|
||
|
|
err_osc:
|
||
|
|
clk_put(gclk);
|
||
|
|
err_gclk:
|
||
|
|
return ret;
|
||
|
|
}
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
|
||
|
|
static struct smc_timing fpga_timing __initdata = {
|
||
|
|
.ncs_read_setup = 16,
|
||
|
|
.nrd_setup = 32,
|
||
|
|
.ncs_read_pulse = 48,
|
||
|
|
.nrd_pulse = 32,
|
||
|
|
.read_cycle = 64,
|
||
|
|
|
||
|
|
.ncs_write_setup = 16,
|
||
|
|
.nwe_setup = 16,
|
||
|
|
.ncs_write_pulse = 32,
|
||
|
|
.nwe_pulse = 32,
|
||
|
|
.write_cycle = 64,
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct smc_config fpga_config __initdata = {
|
||
|
|
.bus_width = 4,
|
||
|
|
.nrd_controlled = 1,
|
||
|
|
.nwe_controlled = 1,
|
||
|
|
.byte_write = 0,
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct resource hh_fpga0_resource[] = {
|
||
|
|
{
|
||
|
|
.start = 0xffe00400,
|
||
|
|
.end = 0xffe00400 + 0x3ff,
|
||
|
|
.flags = IORESOURCE_MEM,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.start = 4,
|
||
|
|
.end = 4,
|
||
|
|
.flags = IORESOURCE_IRQ,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.start = 0x0c000000,
|
||
|
|
.end = 0x0c000100,
|
||
|
|
.flags = IORESOURCE_MEM,
|
||
|
|
},
|
||
|
|
{
|
||
|
|
.start = 67,
|
||
|
|
.end = 67,
|
||
|
|
.flags = IORESOURCE_IRQ,
|
||
|
|
},
|
||
|
|
};
|
||
|
|
|
||
|
|
static u64 hh_fpga0_dma_mask = DMA_BIT_MASK(32);
|
||
|
|
static struct platform_device hh_fpga0_device = {
|
||
|
|
.name = "hh_fpga",
|
||
|
|
.id = 0,
|
||
|
|
.dev = {
|
||
|
|
.dma_mask = &hh_fpga0_dma_mask,
|
||
|
|
.coherent_dma_mask = DMA_BIT_MASK(32),
|
||
|
|
},
|
||
|
|
.resource = hh_fpga0_resource,
|
||
|
|
.num_resources = ARRAY_SIZE(hh_fpga0_resource),
|
||
|
|
};
|
||
|
|
|
||
|
|
static struct clk hh_fpga0_spi_clk = {
|
||
|
|
.name = "spi_clk",
|
||
|
|
.dev = &hh_fpga0_device.dev,
|
||
|
|
.mode = pba_clk_mode,
|
||
|
|
.get_rate = pba_clk_get_rate,
|
||
|
|
.index = 1,
|
||
|
|
};
|
||
|
|
|
||
|
|
struct platform_device *__init at32_add_device_hh_fpga(void)
|
||
|
|
{
|
||
|
|
/* Select peripheral functionallity for SPI SCK and MOSI */
|
||
|
|
at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_SCK,
|
||
|
|
GPIO_PERIPH_B, 0);
|
||
|
|
at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_MOSI,
|
||
|
|
GPIO_PERIPH_B, 0);
|
||
|
|
|
||
|
|
/* reserve all other needed gpio
|
||
|
|
* We have on board pull ups, so there is no need
|
||
|
|
* to enable gpio pull ups */
|
||
|
|
/* INIT_DONE (input) */
|
||
|
|
at32_select_gpio(GPIO_PIN_PB(0), 0);
|
||
|
|
|
||
|
|
/* nSTATUS (input) */
|
||
|
|
at32_select_gpio(GPIO_PIN_PB(2), 0);
|
||
|
|
|
||
|
|
/* nCONFIG (output, low) */
|
||
|
|
at32_select_gpio(GPIO_PIN_PB(3), AT32_GPIOF_OUTPUT);
|
||
|
|
|
||
|
|
/* CONF_DONE (input) */
|
||
|
|
at32_select_gpio(GPIO_PIN_PB(4), 0);
|
||
|
|
|
||
|
|
/* Select EXTINT3 for PB28 (Interrupt from FPGA) */
|
||
|
|
at32_select_periph(GPIO_PIOB_BASE, HAMMERHEAD_FPGA_PERIPH_EXTINT3,
|
||
|
|
GPIO_PERIPH_A, 0);
|
||
|
|
|
||
|
|
/* Get our parent clock */
|
||
|
|
hh_fpga0_spi_clk.parent = clk_get(NULL, "pba");
|
||
|
|
clk_put(hh_fpga0_spi_clk.parent);
|
||
|
|
|
||
|
|
/* Register clock in at32 clock tree */
|
||
|
|
at32_clk_register(&hh_fpga0_spi_clk);
|
||
|
|
|
||
|
|
platform_device_register(&hh_fpga0_device);
|
||
|
|
return &hh_fpga0_device;
|
||
|
|
}
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/* This needs to be called after the SMC has been initialized */
|
||
|
|
static int __init hammerhead_flash_init(void)
|
||
|
|
{
|
||
|
|
int ret;
|
||
|
|
|
||
|
|
smc_set_timing(&flash_config, &flash_timing);
|
||
|
|
ret = smc_set_configuration(0, &flash_config);
|
||
|
|
|
||
|
|
if (ret < 0) {
|
||
|
|
printk(KERN_ERR "hammerhead: failed to set NOR flash timing\n");
|
||
|
|
return ret;
|
||
|
|
}
|
||
|
|
|
||
|
|
platform_device_register(&flash_device);
|
||
|
|
|
||
|
|
#ifdef CONFIG_BOARD_HAMMERHEAD_USB
|
||
|
|
hammerhead_usbh_init();
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifdef CONFIG_BOARD_HAMMERHEAD_FPGA
|
||
|
|
/* Setup SMC for FPGA interface */
|
||
|
|
smc_set_timing(&fpga_config, &fpga_timing);
|
||
|
|
ret = smc_set_configuration(3, &fpga_config);
|
||
|
|
#endif
|
||
|
|
|
||
|
|
|
||
|
|
if (ret < 0) {
|
||
|
|
printk(KERN_ERR "hammerhead: failed to set FPGA timing\n");
|
||
|
|
return ret;
|
||
|
|
}
|
||
|
|
|
||
|
|
return 0;
|
||
|
|
}
|
||
|
|
|
||
|
|
device_initcall(hammerhead_flash_init);
|