satip-axe/kernel/drivers/stm/stx7111_comms.c

547 lines
15 KiB
C
Raw Normal View History

/*
* (c) 2010 STMicroelectronics Limited
*
* Author: Pawel Moll <pawel.moll@st.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/stm/pad.h>
#include <linux/stm/stx7111.h>
#include <asm/irq-ilc.h>
/* ASC resources ---------------------------------------------------------- */
static struct stm_pad_config stx7111_asc_pad_configs[] = {
[0] = {
.gpios_num = 4,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(0, 0, 1), /* TX */
STM_PAD_PIO_IN(0, 1, -1), /* RX */
STM_PAD_PIO_IN_NAMED(0, 4, -1, "CTS"),
STM_PAD_PIO_OUT_NAMED(0, 7, 1, "RTS"),
},
.sysconfs_num = 1, /* !!! see stx7111_configure_asc() */
.sysconfs = (struct stm_pad_sysconf []) {
/* PDES_SCMUX_OUT = 0: route UART0 instead of PDES
* to pins. According to note against
* SYSCFG7[7] this bit is in the PDES block.
* Lets just hope it powers up in UART mode! */
/* Route CTS instead of emiss_bus_request[2] to pins */
STM_PAD_SYS_CFG(5, 3, 3, 0),
},
},
[1] = {
.gpios_num = 4,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(1, 0, 1), /* TX */
STM_PAD_PIO_IN(1, 1, -1), /* RX */
STM_PAD_PIO_IN_NAMED(1, 4, -1, "CTS"),
STM_PAD_PIO_OUT_NAMED(1, 5, 1, "RTS"),
},
.sysconfs_num = 2, /* !!! see stx7111_configure_asc() */
.sysconfs = (struct stm_pad_sysconf []) {
/* Route CTS instead of emiss_bus_free_accesspend_in
* to pins */
STM_PAD_SYS_CFG(5, 6, 6, 0),
/* Route RTS instead of PCI_PME_OUT to pins */
STM_PAD_SYS_CFG(5, 7, 7, 0),
},
},
[2] = {
.gpios_num = 4,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(4, 3, 1), /* TX */
STM_PAD_PIO_IN(4, 2, -1), /* RX */
STM_PAD_PIO_IN_NAMED(4, 4, -1, "CTS"),
STM_PAD_PIO_OUT_NAMED(4, 5, 1, "RTS"),
},
},
[3] = {
.gpios_num = 4,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(5, 0, 1), /* TX */
STM_PAD_PIO_IN(5, 1, -1), /* RX */
STM_PAD_PIO_IN_NAMED(5, 2, -1, "CTS"),
STM_PAD_PIO_OUT_NAMED(5, 3, 1, "RTS"),
},
},
};
static struct platform_device stx7111_asc_devices[] = {
[0] = {
.name = "stm-asc",
/* .id set in stx7111_configure_asc() */
.num_resources = 4,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd030000, 0x2c),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x1160), -1),
STM_PLAT_RESOURCE_DMA_NAMED("rx_half_full", 11),
STM_PLAT_RESOURCE_DMA_NAMED("tx_half_empty", 15),
},
.dev.platform_data = &(struct stm_plat_asc_data) {
.pad_config = &stx7111_asc_pad_configs[0],
},
},
[1] = {
.name = "stm-asc",
/* .id set in stx7111_configure_asc() */
.num_resources = 4,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd031000, 0x2c),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x1140), -1),
STM_PLAT_RESOURCE_DMA_NAMED("rx_half_full", 12),
STM_PLAT_RESOURCE_DMA_NAMED("tx_half_empty", 16),
},
.dev.platform_data = &(struct stm_plat_asc_data) {
.pad_config = &stx7111_asc_pad_configs[1],
},
},
[2] = {
.name = "stm-asc",
/* .id set in stx7111_configure_asc() */
.num_resources = 4,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd032000, 0x2c),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x1120), -1),
STM_PLAT_RESOURCE_DMA_NAMED("rx_half_full", 13),
STM_PLAT_RESOURCE_DMA_NAMED("tx_half_empty", 17),
},
.dev.platform_data = &(struct stm_plat_asc_data) {
.pad_config = &stx7111_asc_pad_configs[2],
},
},
[3] = {
.name = "stm-asc",
/* .id set in stx7111_configure_asc() */
.num_resources = 4,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd033000, 0x2c),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x1100), -1),
STM_PLAT_RESOURCE_DMA_NAMED("rx_half_full", 14),
STM_PLAT_RESOURCE_DMA_NAMED("tx_half_empty", 18),
},
.dev.platform_data = &(struct stm_plat_asc_data) {
.pad_config = &stx7111_asc_pad_configs[3],
},
},
};
/* Note these three variables are global, and shared with the stasc driver
* for console bring up prior to platform initialisation. */
/* the serial console device */
int __initdata stm_asc_console_device;
/* Platform devices to register */
unsigned int __initdata stm_asc_configured_devices_num = 0;
struct platform_device __initdata
*stm_asc_configured_devices[ARRAY_SIZE(stx7111_asc_devices)];
void __init stx7111_configure_asc(int asc, struct stx7111_asc_config *config)
{
static int configured[ARRAY_SIZE(stx7111_asc_devices)];
static int tty_id;
struct stx7111_asc_config default_config = {};
struct platform_device *pdev;
struct stm_plat_asc_data *plat_data;
BUG_ON(asc < 0 || asc >= ARRAY_SIZE(stx7111_asc_devices));
BUG_ON(configured[asc]);
configured[asc] = 1;
if (!config)
config = &default_config;
if (!config->hw_flow_control) {
struct stm_pad_config *pad_config =
&stx7111_asc_pad_configs[asc];
/* Don't claim RTS/CTS pads */
stm_pad_set_pio_ignored(pad_config, "RTS");
stm_pad_set_pio_ignored(pad_config, "CTS");
/* sysconf values responsible for RTS/CTS routing
* are defined as the last ones... */
if (asc == 0)
pad_config->sysconfs_num--;
else if (asc == 1)
pad_config->sysconfs_num -= 2;
}
pdev = &stx7111_asc_devices[asc];
plat_data = pdev->dev.platform_data;
pdev->id = tty_id++;
plat_data->hw_flow_control = config->hw_flow_control;
if (config->is_console)
stm_asc_console_device = pdev->id;
stm_asc_configured_devices[stm_asc_configured_devices_num++] = pdev;
}
/* Add platform device as configured by board specific code */
static int __init stx7111_add_asc(void)
{
return platform_add_devices(stm_asc_configured_devices,
stm_asc_configured_devices_num);
}
arch_initcall(stx7111_add_asc);
/* SSC resources ---------------------------------------------------------- */
/* Pad configuration for I2C mode */
static struct stm_pad_config stx7111_ssc_i2c_pad_configs[] = {
[0] = {
.gpios_num = 2,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_BIDIR_NAMED(2, 0, 1, "SCL"),
STM_PAD_PIO_BIDIR_NAMED(2, 1, 1, "SDA"),
},
.sysconfs_num = 1,
.sysconfs = (struct stm_pad_sysconf []) {
/* SSC0_MUX_SEL = 0 (default assignment) */
STM_PAD_SYS_CFG(7, 1, 1, 0),
/* spi_boot_not_comm = 0 should be set here... */
/* This is a signal from SPI block */
/* Hope this is set correctly by default */
},
},
[1] = {
.gpios_num = 2,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_BIDIR_NAMED(3, 0, 1, "SCL"),
STM_PAD_PIO_BIDIR_NAMED(3, 1, 1, "SDA"),
},
.sysconfs_num = 3,
.sysconfs = (struct stm_pad_sysconf []) {
/* SSC1_MUX_SEL = 0 (default assignment) */
STM_PAD_SYS_CFG(7, 2, 2, 0),
/* dvo_out=0 */
STM_PAD_SYS_CFG(7, 10, 10, 0),
/* Select SSC1 instead of PCI interrupts */
/* Early datasheet version erroneously said 9-11 */
STM_PAD_SYS_CFG(5, 11, 12, 0),
},
},
[2] = {
.gpios_num = 2,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_BIDIR_NAMED(4, 0, 1, "SCL"),
STM_PAD_PIO_BIDIR_NAMED(4, 1, 1, "SDA"),
},
.sysconfs_num = 1,
.sysconfs = (struct stm_pad_sysconf []) {
/* SSC2_MUX_SEL = 0 (default assignment) */
STM_PAD_SYS_CFG(7, 3, 3, 0),
},
},
/* SSC3 is an internal I2C link - doesn't need any
* special treatment here... */
};
/* Pad configuration for SPI mode */
static struct stm_pad_config stx7111_ssc_spi_pad_configs[] = {
[0] = {
.gpios_num = 3,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(2, 0, 1), /* SCK */
STM_PAD_PIO_OUT(2, 1, 1), /* MOSI */
STM_PAD_PIO_IN(2, 2, -1), /* MISO */
},
.sysconfs_num = 1,
.sysconfs = (struct stm_pad_sysconf []) {
/* SSC0_MUX_SEL = 0 (default assignment) */
STM_PAD_SYS_CFG(7, 1, 1, 0),
/* spi_boot_not_comm = 0 should be set here... */
/* This is a signal from SPI block */
/* Hope this is set correctly by default */
},
},
[1] = {
.gpios_num = 3,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(3, 0, 1), /* SCK */
STM_PAD_PIO_OUT(3, 1, 1), /* MOSI */
STM_PAD_PIO_IN(3, 2, -1), /* MISO */
},
.sysconfs_num = 3,
.sysconfs = (struct stm_pad_sysconf []) {
/* SSC1_MUX_SEL = 0 (default assignment) */
STM_PAD_SYS_CFG(7, 2, 2, 0),
/* dvo_out=0 */
STM_PAD_SYS_CFG(7, 10, 10, 0),
/* Select SSC1 instead of PCI interrupts */
/* Early datasheet version erroneously said 9-11 */
STM_PAD_SYS_CFG(5, 10, 12, 0),
},
},
};
static struct platform_device stx7111_ssc_devices[] = {
[0] = {
/* .name & .id set in stx7111_configure_ssc_*() */
.num_resources = 2,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd040000, 0x110),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x10e0), -1),
},
.dev.platform_data = &(struct stm_plat_ssc_data) {
/* .pad_config_* set in stx7111_configure_ssc_*() */
},
},
[1] = {
/* .name & .id set in stx7111_configure_ssc_*() */
.num_resources = 2,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd041000, 0x110),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x10c0), -1),
},
.dev.platform_data = &(struct stm_plat_ssc_data) {
/* .pad_config_* set in stx7111_configure_ssc_*() */
},
},
[2] = {
/* .name & .id set in stx7111_configure_ssc_*() */
.num_resources = 2,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd042000, 0x110),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x10a0), -1),
},
.dev.platform_data = &(struct stm_plat_ssc_data) {
/* .pad_config_* set in stx7111_configure_ssc_*() */
},
},
[3] = {
/* .name & .id set in stx7111_configure_ssc_*() */
.num_resources = 2,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd043000, 0x110),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x1080), -1),
},
.dev.platform_data = &(struct stm_plat_ssc_data) {
/* That's an internal I2C link - nothing
* to say here actually... */
},
},
};
static int __initdata stx7111_ssc_configured[ARRAY_SIZE(stx7111_ssc_devices)];
int __init stx7111_configure_ssc_i2c(int ssc)
{
static int i2c_busnum;
BUG_ON(ssc < 0 || ssc >= ARRAY_SIZE(stx7111_ssc_devices));
BUG_ON(stx7111_ssc_configured[ssc]);
stx7111_ssc_configured[ssc] = 1;
stx7111_ssc_devices[ssc].name = "i2c-stm";
stx7111_ssc_devices[ssc].id = i2c_busnum;
/* The SSC3 is an internal I2C link and is hard-wired -
* no pads to be claimed here... */
if (ssc < 3) {
struct stm_plat_ssc_data *plat_data =
stx7111_ssc_devices[ssc].dev.platform_data;
plat_data->pad_config =
&stx7111_ssc_i2c_pad_configs[ssc];
}
/* I2C bus number reservation (to prevent any hot-plug device
* from using it) */
i2c_register_board_info(i2c_busnum, NULL, 0);
platform_device_register(&stx7111_ssc_devices[ssc]);
return i2c_busnum++;
}
int __init stx7111_configure_ssc_spi(int ssc,
struct stx7111_ssc_spi_config *config)
{
static int spi_busnum;
struct stm_plat_ssc_data *plat_data;
BUG_ON(ssc < 0 || ssc >= ARRAY_SIZE(stx7111_ssc_devices));
BUG_ON(stx7111_ssc_configured[ssc]);
stx7111_ssc_configured[ssc] = 1;
/* Only first two SSC can be used in SPI mode */
BUG_ON(ssc > 1);
stx7111_ssc_devices[ssc].name = "spi-stm";
stx7111_ssc_devices[ssc].id = spi_busnum;
plat_data = stx7111_ssc_devices[ssc].dev.platform_data;
if (config)
plat_data->spi_chipselect = config->chipselect;
plat_data->pad_config = &stx7111_ssc_spi_pad_configs[ssc];
platform_device_register(&stx7111_ssc_devices[ssc]);
return spi_busnum++;
}
/* LiRC resources --------------------------------------------------------- */
static struct platform_device stx7111_lirc_device = {
.name = "lirc-stm",
.id = -1,
.num_resources = 2,
.resource = (struct resource []) {
STM_PLAT_RESOURCE_MEM(0xfd018000, 0x234),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x11a0), -1),
},
.dev.platform_data = &(struct stm_plat_lirc_data) {
/* The clock settings will be calculated by
* the driver from the system clock */
.irbclock = 0, /* use current_cpu data */
.irbclkdiv = 0, /* automatically calculate */
.irbperiodmult = 0,
.irbperioddiv = 0,
.irbontimemult = 0,
.irbontimediv = 0,
.irbrxmaxperiod = 0x5000,
.sysclkdiv = 1,
.rxpolarity = 1,
},
};
void __init stx7111_configure_lirc(struct stx7111_lirc_config *config)
{
static int configured;
struct stx7111_lirc_config default_config = {};
struct stm_plat_lirc_data *plat_data =
stx7111_lirc_device.dev.platform_data;
struct stm_pad_config *pad_config;
BUG_ON(configured);
configured = 1;
if (!config)
config = &default_config;
pad_config = stm_pad_config_alloc(3, 0);
BUG_ON(!pad_config);
plat_data->txenabled = config->tx_enabled || config->tx_od_enabled;
plat_data->pads = pad_config;
switch (config->rx_mode) {
case stx7111_lirc_rx_disabled:
/* Nothing to do */
break;
case stx7111_lirc_rx_mode_ir:
plat_data->rxuhfmode = 0;
stm_pad_config_add_pio_in(pad_config, 3, 3, -1);
break;
case stx7111_lirc_rx_mode_uhf:
plat_data->rxuhfmode = 1;
stm_pad_config_add_pio_in(pad_config, 3, 4, -1);
break;
default:
BUG();
break;
}
if (config->tx_enabled)
stm_pad_config_add_pio_out(pad_config, 3, 5, 1);
if (config->tx_od_enabled)
stm_pad_config_add_pio_out(pad_config, 3, 6, 1);
platform_device_register(&stx7111_lirc_device);
}
/* PWM resources ---------------------------------------------------------- */
static struct stm_plat_pwm_data stx7111_pwm_platform_data = {
.channel_pad_config = {
[0] = &(struct stm_pad_config) {
.gpios_num = 1,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(4, 6, 1),
},
},
[1] = &(struct stm_pad_config) {
.gpios_num = 1,
.gpios = (struct stm_pad_gpio []) {
STM_PAD_PIO_OUT(4, 7, 1),
},
},
},
};
static struct platform_device stx7111_pwm_device = {
.name = "stm-pwm",
.id = -1,
.num_resources = 2,
.resource = (struct resource[]) {
STM_PLAT_RESOURCE_MEM(0xfd010000, 0x68),
STM_PLAT_RESOURCE_IRQ(evt2irq(0x11c0), -1),
},
.dev.platform_data = &stx7111_pwm_platform_data,
};
void __init stx7111_configure_pwm(struct stx7111_pwm_config *config)
{
static int configured;
BUG_ON(configured);
configured = 1;
if (config) {
stx7111_pwm_platform_data.channel_enabled[0] =
config->out0_enabled;
stx7111_pwm_platform_data.channel_enabled[1] =
config->out1_enabled;
}
platform_device_register(&stx7111_pwm_device);
}
/* Low Power Controller ---------------------------------------------------- */
static struct platform_device stx7111_lpc_device = {
.name = "stm-rtc",
.id = -1,
.num_resources = 2,
.resource = (struct resource[]){
STM_PLAT_RESOURCE_MEM(0xfd008000, 0x600),
STM_PLAT_RESOURCE_IRQ(ILC_EXT_IRQ(7), -1),
},
.dev.platform_data = &(struct stm_plat_rtc_lpc) {
.clk_id = "CLKB_LPC",
.need_wdt_reset = 1,
.irq_edge_level = IRQ_TYPE_EDGE_FALLING,
}
};
static int __init stx7111_add_lpc(void)
{
return platform_device_register(&stx7111_lpc_device);
}
module_init(stx7111_add_lpc);