satip-axe/kernel/arch/sh/boards/mach-mb628/setup.c

570 lines
16 KiB
C
Raw Normal View History

/*
* arch/sh/boards/st/mb628/setup.c
*
* Copyright (C) 2008 STMicroelectronics Limited
* Author: Stuart Menefy (stuart.menefy@st.com)
*
* May be copied or modified under the terms of the GNU General Public
* License. See linux/COPYING for more information.
*
* STMicroelectronics STx7141 Mboard support.
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/phy.h>
#include <linux/lirc.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/stm/emi.h>
#include <linux/stm/platform.h>
#include <linux/stm/stx7141.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/partitions.h>
#include <asm/irq-ilc.h>
#include <asm/irl.h>
#include <mach/epld.h>
#include <sound/stm.h>
#include <mach/common.h>
/*
* Flash setup depends on boot-device:
*
* boot-from-XXX
* NOR NAND
* ---------------------------------------------------------------------
* J70 (CS routing) 2-3 (EMIA->NOR_CS) 1-2 (EMIA->NAND_CS)
* SW8-4 (mode 14:bus width) ON (16bit) OFF (8bit)
* SW9-1 (mode 16,17) ON (boot NOR) OFF (boot NAND)
* SW9-2 ON ON
* ---------------------------------------------------------------------
*
* Notes: SW8-4 was found not to work correctly on early rev A boards.
* J69 must be in position 2-3 to enable the on-board Flash devices (both
* NOR and NAND) rather than STEM).
* J89 and J84 must be both in position 1-2 to avoid shorting A15.
* Board modifications are required to achieve boot from SPI (not
* supported here).
* Jumper settings based on board rev A
*/
static struct platform_device mb628_epld_device;
static void __init mb628_setup(char **cmdline_p)
{
u8 test;
printk(KERN_INFO "STMicroelectronics STx7141 Mboard initialisation\n");
stx7141_early_device_init();
#ifndef CONFIG_SH_ST_MB628_STMMAC0
/* Cannot use the ASC 1 when configure the GMAC0
* due to a PIO conflict */
stx7141_configure_asc(1, &(struct stx7141_asc_config) {
.routing.asc1 = stx7141_asc1_pio10,
.hw_flow_control = 1,
.is_console = 1, });
#endif
stx7141_configure_asc(2, &(struct stx7141_asc_config) {
.routing.asc2 = stx7141_asc2_pio6,
.hw_flow_control = 1,
.is_console = 0, });
epld_early_init(&mb628_epld_device);
epld_write(0xab, EPLD_TEST);
test = epld_read(EPLD_TEST);
printk(KERN_INFO "mb628 EPLD version %ld, test %s\n",
epld_read(EPLD_IDENT),
(test == (u8)(~0xab)) ? "passed" : "failed");
}
/* Serial Flash Chip Select
*
* SPI_CS is controlled via an EPLD register. Here we create a virtual GPIO
* device which maps onto the register. This allows the default SPI chip select
* function to be used.
*/
#define EPLD_SPI_CHIPSELECT_GPIO_BASE 200 /* Avoid clash with real PIOs */
static void epld_spi_chipselect_set(struct gpio_chip *chip, unsigned offset,
int value)
{
u8 reg;
reg = epld_read(EPLD_ENABLE);
if (value)
reg |= EPLD_ENABLE_SPI_NOTCS;
else
reg &= ~EPLD_ENABLE_SPI_NOTCS;
epld_write(reg, EPLD_ENABLE);
}
static int epld_spi_chipselect_output(struct gpio_chip *chip, unsigned offset,
int value)
{
epld_spi_chipselect_set(chip, offset, value);
return 0;
}
static struct gpio_chip epld_spi_chipselect = {
.set = epld_spi_chipselect_set,
.direction_output = epld_spi_chipselect_output,
.base = EPLD_SPI_CHIPSELECT_GPIO_BASE,
.ngpio = 1,
};
/* Serial Flash */
static struct spi_board_info mb628_serial_flash = {
.modalias = "m25p80",
.bus_num = 0,
.chip_select = EPLD_SPI_CHIPSELECT_GPIO_BASE,
.max_speed_hz = 7000000,
.mode = SPI_MODE_3,
.platform_data = &(struct flash_platform_data) {
.name = "m25p80",
.type = "m25p32",
.nr_parts = 2,
.parts = (struct mtd_partition []) {
{
.name = "Serial Flash 1",
.size = 0x00080000,
.offset = 0,
}, {
.name = "Serial Flash 2",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_NXTBLK,
},
},
}
};
/* NOR Flash */
static void mb628_nor_set_vpp(struct map_info *info, int enable)
{
epld_write((enable ? EPLD_FLASH_NOTWP : 0) | EPLD_FLASH_NOTRESET,
EPLD_FLASH);
}
static struct platform_device mb628_nor_flash = {
.name = "physmap-flash",
.id = -1,
.num_resources = 1,
.resource = (struct resource[]) {
/* updated in mb628_device_init() */
STM_PLAT_RESOURCE_MEM(0, 32*1024*1024),
},
.dev.platform_data = &(struct physmap_flash_data) {
.width = 2,
.set_vpp = mb628_nor_set_vpp,
.nr_parts = 3,
.parts = (struct mtd_partition []) {
{
.name = "NOR Flash 1",
.size = 0x00080000,
.offset = 0x00000000,
}, {
.name = "NOR Flash 2",
.size = 0x00200000,
.offset = MTDPART_OFS_NXTBLK,
}, {
.name = "NOR Flash 3",
.size = MTDPART_SIZ_FULL,
.offset = MTDPART_OFS_NXTBLK,
},
},
},
};
/* NAND Flash */
static struct stm_nand_bank_data mb628_nand_flash = {
.csn = 0, /* updated in mb628_device_init() */
.options = NAND_NO_AUTOINCR | NAND_USE_FLASH_BBT,
.nr_partitions = 2,
.partitions = (struct mtd_partition []) {
{
.name = "NAND Flash 1",
.offset = 0,
.size = 0x00800000
}, {
.name = "NAND Flash 2",
.offset = MTDPART_OFS_NXTBLK,
.size = MTDPART_SIZ_FULL
},
},
.timing_data = &(struct stm_nand_timing_data) {
.sig_setup = 10, /* times in ns */
.sig_hold = 10,
.CE_deassert = 0,
.WE_to_RBn = 100,
.wr_on = 10,
.wr_off = 40,
.rd_on = 10,
.rd_off = 40,
.chip_delay = 30, /* in us */
},
.emi_withinbankoffset = 0,
};
static int mb628_phy_reset(void *bus)
{
u8 reg;
static int first = 1;
/* Both PHYs share the same reset signal, only act on the first. */
if (!first)
return 1;
first = 0;
reg = epld_read(EPLD_RESET);
reg &= ~EPLD_RESET_MII;
epld_write(reg, EPLD_RESET);
udelay(150);
reg |= EPLD_RESET_MII;
epld_write(reg, EPLD_RESET);
/* DP83865 (PHY chip) has a looong initialization
* procedure... Let's give him some time to settle down... */
udelay(1000);
/*
* The SMSC LAN8700 requires a 21mS delay after reset. This
* matches the power on reset signal period, which should only
* be applied after power on, but experimentally appears to be
* applied post reset as well.
*/
mdelay(25);
return 1;
}
/*
* Several things need to be configured to use the GMAC0 with the
* mb539 - SMSC LAN8700 PHY board:
*
* - normally the PHY's internal 1V8 regulator is used, which is
* is enabled at PHY power up (not reset) by sampling RXCLK/REGOFF.
* It appears that the STx7141's internal pull up resistor on this
* signal is enabled at power on, defeating the internal pull down
* in the SMSC device. Thus it is necessary to fix an external
* pull down resistor to RXCLK/REGOFF. 10K appears to be sufficient.
*
* Alternativly fitting J2 on the mb539 supplies power from an
* off-chip regulator, working around this problem.
*
* - various signals are muxed with the MII pins (as well as DVO_DATA).
* + ASC1_RXD and ASC1_RTS, so make sure J101 is set to 2-3. This
* allows the EPLD to disable the level converter.
* + PCIREQ1 and PCIREQ2 need to be disabled by removing J104 and J98
* (near the PCI slot).
* + SYSITRQ1 needs to be disabled, which requires removing R232
* (near CN17). See DDTS INSbl29196 for details.
* + PCIGNT2 needs to be disabled. This can be done either by removing
* R241, or by ensuring that jumper J89 is not in position 1-2 (by
* either removing it completely or putting it in position 2-3).
*
* - other jumper and switch settings for the mb539:
* + J1 fit 1-2 (use on board crystal)
* + SW1: 1:on, 2:off, 3:off, 4:off
* + SW2: 1:off, 2:off, 3:off, 4:off
*
* - For reliable SMI signalling it is necessary to have a
* pull up resistor on the MDIO signal. This can be done by
* installing R3 on the mb539 which is normally a DNF.
*
* - to use the MDINT signal, R148 needs to be in position 1-2.
* To disable this, replace the irq with -1 in the data below.
*/
#ifdef CONFIG_SH_ST_MB628_STMMAC0
static struct stmmac_mdio_bus_data stmmac0_mdio_bus = {
.bus_id = 0,
.phy_reset = mb628_phy_reset,
.phy_mask = 0,
.probed_phy_irq = ILC_IRQ(43),
};
#endif
static struct stmmac_mdio_bus_data stmmac1_mdio_bus = {
.bus_id = 1,
.phy_reset = mb628_phy_reset,
.phy_mask = 0,
};
static struct platform_device mb628_epld_device = {
.name = "epld",
.id = -1,
.num_resources = 1,
.resource = (struct resource[]) {
{
.start = 0x05000000,
/* Minimum size to ensure mapped by PMB */
.end = 0x05000000+(8*1024*1024)-1,
.flags = IORESOURCE_MEM,
}
},
.dev.platform_data = &(struct plat_epld_data) {
.opsize = 8,
},
};
#ifdef CONFIG_SND
/* CS8416 SPDIF to I2S converter (IC14) */
static struct platform_device mb628_snd_spdif_input = {
.name = "snd_conv_dummy",
.id = -1,
.dev.platform_data = &(struct snd_stm_conv_dummy_info) {
.group = "SPDIF Input",
.source_bus_id = "snd_pcm_reader.0",
.channel_from = 0,
.channel_to = 1,
.format = SND_STM_FORMAT__I2S |
SND_STM_FORMAT__SUBFRAME_32_BITS,
},
};
static struct platform_device mb628_snd_external_dacs = {
.name = "snd_conv_epld",
.id = -1,
.dev.platform_data = &(struct snd_stm_conv_epld_info) {
.group = "External DACs",
.source_bus_id = "snd_pcm_player.0",
.channel_from = 0,
.channel_to = 9,
.format = SND_STM_FORMAT__I2S |
SND_STM_FORMAT__SUBFRAME_32_BITS,
.oversampling = 256,
.mute_supported = 1,
.mute_offset = EPLD_AUDIO,
.mute_mask = EPLD_AUDIO_PCMDAC1_SMUTE |
EPLD_AUDIO_PCMDAC2_SMUTE,
.mute_value = EPLD_AUDIO_PCMDAC1_SMUTE |
EPLD_AUDIO_PCMDAC2_SMUTE,
.unmute_value = 0,
},
};
#endif
static struct platform_device *mb628_devices[] __initdata = {
&mb628_epld_device,
#ifdef CONFIG_SND
&mb628_snd_spdif_input,
&mb628_snd_external_dacs,
#endif
};
static int __init mb628_device_init(void)
{
struct sysconf_field *sc;
/* Configure FLASH devices */
sc = sysconf_claim(SYS_STA, 1, 16, 17, "boot_mode");
switch (sysconf_read(sc)) {
case 0x0:
/* Boot-from-NOR: */
pr_info("Configuring FLASH for boot-from-NOR\n");
mb628_nor_flash.resource[0].start = 0x00000000;
mb628_nor_flash.resource[0].end = emi_bank_base(1) - 1;
platform_device_register(&mb628_nor_flash);
break;
case 0x1:
/* Boot-from-NAND */
pr_info("Configuring FLASH for boot-from-NAND\n");
mb628_nand_flash.csn = 0;
stx7141_configure_nand(&(struct stm_nand_config) {
.driver = stm_nand_flex,
.nr_banks = 1,
.banks = &mb628_nand_flash,
.rbn.flex_connected = 1,});
/* The MTD NAND code doesn't understand the concept of VPP, (or
* hardware write protect) so permanently enable it.
*/
epld_write(EPLD_FLASH_NOTWP | EPLD_FLASH_NOTRESET, EPLD_FLASH);
break;
default:
BUG();
break;
}
/*
* Can't enable PWM output without conflicting with either
* SSC6 (audio) or USB1A OC (which is disabled in cut 1 because it
* has the wrong OC polarity but would still result in contention).
*
* stx7141_configure_pwm(0, 1);
*/
stx7141_configure_ssc_spi(0, NULL);
stx7141_configure_ssc_spi(1, NULL);
stx7141_configure_ssc_i2c(2);
stx7141_configure_ssc_i2c(3);
stx7141_configure_ssc_i2c(4);
stx7141_configure_ssc_i2c(5);
stx7141_configure_ssc_i2c(6);
stx7141_configure_usb(0, &(struct stx7141_usb_config) {
.ovrcur_mode = stx7141_usb_ovrcur_active_low,
.pwr_enabled = 1 });
/* This requires fitting jumpers J52A 1-2 and J52B 4-5 */
stx7141_configure_usb(1, &(struct stx7141_usb_config) {
.ovrcur_mode = stx7141_usb_ovrcur_active_low,
.pwr_enabled = 1 });
/*
* USB1.1 ports on mb628 rev A are missing the series
* resistors, which can make them unreliable, and also the
* pull down resistors, which causes them to report spurious
* device connection. Unfortunately we can't determine board
* revision, but most boards are now rev B, so make the ports
* available here. Boards with cut 1 Si will have these ports
* disabled anyway, becuase the OC polarity is wrong. Users
* with rev A boards and cut 2 Si will need to remove these
* lines.
*/
stx7141_configure_usb(2, &(struct stx7141_usb_config) {
.ovrcur_mode = stx7141_usb_ovrcur_active_low,
.pwr_enabled = 1 });
stx7141_configure_usb(3, &(struct stx7141_usb_config) {
.ovrcur_mode = stx7141_usb_ovrcur_active_low,
.pwr_enabled = 1 });
stx7141_configure_sata();
/* Note R253 must be removed for Ethernet MDIO signal to work. */
#ifdef CONFIG_SH_ST_MB628_STMMAC0
/* Must disable ASC1 if using GMII0 */
epld_write(epld_read(EPLD_ENABLE) | EPLD_ASC1_EN | EPLD_ENABLE_MII0,
EPLD_ENABLE);
/* Configure GMII0 MDINT for active low */
set_irq_type(ILC_IRQ(43), IRQ_TYPE_LEVEL_LOW);
stx7141_configure_ethernet(0, &(struct stx7141_ethernet_config) {
.mode = stx7141_ethernet_mode_mii,
.phy_bus = 0,
.phy_addr = -1,
.mdio_bus_data = &stmmac0_mdio_bus,
});
#endif
epld_write(epld_read(EPLD_ENABLE) | EPLD_ENABLE_MII1, EPLD_ENABLE);
stx7141_configure_ethernet(1, &(struct stx7141_ethernet_config) {
.mode = stx7141_ethernet_mode_gmii,
.phy_bus = 1,
.phy_addr = -1,
.mdio_bus_data = &stmmac1_mdio_bus,
});
stx7141_configure_lirc(&(struct stx7141_lirc_config) {
.rx_mode = stx7141_lirc_rx_disabled,
.tx_enabled = 1,
.tx_od_enabled = 1 });
/* Audio peripherals
*
* WARNING! Board rev. A has swapped silkscreen labels of J16 & J32!
*
* The recommended audio setup of MB628 is as follows:
* SW2[1..4] - [ON, OFF, OFF, ON]
* SW5[1..4] - [OFF, OFF, OFF, OFF]
* SW3[1..4] - [OFF, OFF, ON, OFF]
* SW12[1..4] - [OFF, OFF, OFF, OFF]
* SW13[1..4] - [OFF, OFF, OFF, OFF]
* J2 - 2-3
* J3 - 1-2
* J6 - 1-2
* J7 - 1-2
* J8 - 1-2
* J12 - 1-2
* J16-A - 1-2, J16-B - 1-2
* J23-A - 2-3, J23-B - 2-3
* J26-A - 1-2, J26-B - 2-3
* J34-A - 1-2, J34-B - 2-3
* J41-A - 3-2, J41-B - 3-2
*
* Additionally the audio EPLD should be updated to the latest
* available release.
*
* With such settings the audio outputs layout presents as follows:
*
* +--------------------------------------+
* | |
* | (S.I) (1.R) (1.L) (0.4) (0.3) | TOP
* | |
* | (---) (0.2) (0.1) (0.10) (0.9) |
* | |
* | (S.O) (0.6) (0.5) (0.8) (0.7) | BOTTOM
* | |
* +--------------------------------------+
* CN6 CN5 CN4 CN3 CN2
*
* where:
* - S.I - SPDIF input - PCM Reader #0
* - S.O - SPDIF output - SPDIF Player (HDMI)
* - 1.R, 1.L - audio outputs - PCM Player #1, channel L(1)/R(2)
* - 0.1-10 - audio outputs - PCM Player #0, channels 1 to 10
*/
/* As digital audio outputs are now GPIOs, we have to claim them... */
stx7141_configure_audio(&(struct stx7141_audio_config) {
.pcm_player_0_output =
stx7141_pcm_player_0_output_10_channels,
.pcm_player_1_output_enabled = 0,
.spdif_player_output_enabled = 1,
.pcm_reader_0_input_enabled = 1,
.pcm_reader_1_input_enabled = 1 });
/* We use both DACs to get full 10-channels output from
* PCM Player #0 (EPLD muxing mode #1) */
{
unsigned int value = epld_read(EPLD_AUDIO);
value &= ~(EPLD_AUDIO_AUD_SW_CTRL_MASK <<
EPLD_AUDIO_AUD_SW_CTRL_SHIFT);
value |= 0x1 << EPLD_AUDIO_AUD_SW_CTRL_SHIFT;
epld_write(value, EPLD_AUDIO);
}
gpiochip_add(&epld_spi_chipselect);
spi_register_board_info(&mb628_serial_flash, 1);
return platform_add_devices(mb628_devices, ARRAY_SIZE(mb628_devices));
}
arch_initcall(mb628_device_init);
static void __iomem *mb628_ioport_map(unsigned long port, unsigned int size)
{
/*
* No IO ports on this device, but to allow safe probing pick
* somewhere safe to redirect all reads and writes.
*/
return (void __iomem *)CCN_PVR;
}
static void __init mb628_init_irq(void)
{
}
struct sh_machine_vector mv_mb628 __initmv = {
.mv_name = "mb628",
.mv_setup = mb628_setup,
.mv_nr_irqs = NR_IRQS,
.mv_init_irq = mb628_init_irq,
.mv_ioport_map = mb628_ioport_map,
};