185 lines
5.8 KiB
Plaintext
185 lines
5.8 KiB
Plaintext
|
#
|
||
|
|
# USB Dual Role (OTG-ready) Controller Drivers
|
||
|
|
# for silicon based on Mentor Graphics INVENTRA designs
|
||
|
|
#
|
||
|
|
|
||
|
|
comment "Enable Host or Gadget support to see Inventra options"
|
||
|
|
depends on !USB && USB_GADGET=n
|
||
|
|
|
||
|
|
# (M)HDRC = (Multipoint) Highspeed Dual-Role Controller
|
||
|
|
config USB_MUSB_HDRC
|
||
|
|
depends on (USB || USB_GADGET)
|
||
|
|
depends on (ARM || BLACKFIN)
|
||
|
|
select NOP_USB_XCEIV if ARCH_DAVINCI
|
||
|
|
select TWL4030_USB if MACH_OMAP_3430SDP
|
||
|
|
select NOP_USB_XCEIV if MACH_OMAP3EVM
|
||
|
|
select USB_OTG_UTILS
|
||
|
|
tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)'
|
||
|
|
help
|
||
|
|
Say Y here if your system has a dual role high speed USB
|
||
|
|
controller based on the Mentor Graphics silicon IP. Then
|
||
|
|
configure options to match your silicon and the board
|
||
|
|
it's being used with, including the USB peripheral role,
|
||
|
|
or the USB host role, or both.
|
||
|
|
|
||
|
|
Texas Instruments familiies using this IP include DaVinci
|
||
|
|
(35x, 644x ...), OMAP 243x, OMAP 3, and TUSB 6010.
|
||
|
|
|
||
|
|
Analog Devices parts using this IP include Blackfin BF54x,
|
||
|
|
BF525 and BF527.
|
||
|
|
|
||
|
|
If you do not know what this is, please say N.
|
||
|
|
|
||
|
|
To compile this driver as a module, choose M here; the
|
||
|
|
module will be called "musb_hdrc".
|
||
|
|
|
||
|
|
config USB_MUSB_SOC
|
||
|
|
boolean
|
||
|
|
depends on USB_MUSB_HDRC
|
||
|
|
default y if ARCH_DAVINCI
|
||
|
|
default y if ARCH_OMAP2430
|
||
|
|
default y if ARCH_OMAP34XX
|
||
|
|
default y if (BF54x && !BF544)
|
||
|
|
default y if (BF52x && !BF522 && !BF523)
|
||
|
|
|
||
|
|
comment "DaVinci 35x and 644x USB support"
|
||
|
|
depends on USB_MUSB_HDRC && ARCH_DAVINCI
|
||
|
|
|
||
|
|
comment "OMAP 243x high speed USB support"
|
||
|
|
depends on USB_MUSB_HDRC && ARCH_OMAP2430
|
||
|
|
|
||
|
|
comment "OMAP 343x high speed USB support"
|
||
|
|
depends on USB_MUSB_HDRC && ARCH_OMAP34XX
|
||
|
|
|
||
|
|
comment "Blackfin high speed USB Support"
|
||
|
|
depends on USB_MUSB_HDRC && ((BF54x && !BF544) || (BF52x && !BF522 && !BF523))
|
||
|
|
|
||
|
|
config USB_TUSB6010
|
||
|
|
boolean "TUSB 6010 support"
|
||
|
|
depends on USB_MUSB_HDRC && !USB_MUSB_SOC
|
||
|
|
select NOP_USB_XCEIV
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
The TUSB 6010 chip, from Texas Instruments, connects a discrete
|
||
|
|
HDRC core using a 16-bit parallel bus (NOR flash style) or VLYNQ
|
||
|
|
(a high speed serial link). It can use system-specific external
|
||
|
|
DMA controllers.
|
||
|
|
|
||
|
|
choice
|
||
|
|
prompt "Driver Mode"
|
||
|
|
depends on USB_MUSB_HDRC
|
||
|
|
help
|
||
|
|
Dual-Role devices can support both host and peripheral roles,
|
||
|
|
as well as a the special "OTG Device" role which can switch
|
||
|
|
between both roles as needed.
|
||
|
|
|
||
|
|
# use USB_MUSB_HDRC_HCD not USB_MUSB_HOST to #ifdef host side support;
|
||
|
|
# OTG needs both roles, not just USB_MUSB_HOST.
|
||
|
|
config USB_MUSB_HOST
|
||
|
|
depends on USB
|
||
|
|
bool "USB Host"
|
||
|
|
help
|
||
|
|
Say Y here if your system supports the USB host role.
|
||
|
|
If it has a USB "A" (rectangular), "Mini-A" (uncommon),
|
||
|
|
or "Mini-AB" connector, it supports the host role.
|
||
|
|
(With a "Mini-AB" connector, you should enable USB OTG.)
|
||
|
|
|
||
|
|
# use USB_GADGET_MUSB_HDRC not USB_MUSB_PERIPHERAL to #ifdef peripheral
|
||
|
|
# side support ... OTG needs both roles
|
||
|
|
config USB_MUSB_PERIPHERAL
|
||
|
|
depends on USB_GADGET
|
||
|
|
bool "USB Peripheral (gadget stack)"
|
||
|
|
select USB_GADGET_MUSB_HDRC
|
||
|
|
help
|
||
|
|
Say Y here if your system supports the USB peripheral role.
|
||
|
|
If it has a USB "B" (squarish), "Mini-B", or "Mini-AB"
|
||
|
|
connector, it supports the peripheral role.
|
||
|
|
(With a "Mini-AB" connector, you should enable USB OTG.)
|
||
|
|
|
||
|
|
config USB_MUSB_OTG
|
||
|
|
depends on USB && USB_GADGET && PM && EXPERIMENTAL
|
||
|
|
bool "Both host and peripheral: USB OTG (On The Go) Device"
|
||
|
|
select USB_GADGET_MUSB_HDRC
|
||
|
|
select USB_OTG
|
||
|
|
help
|
||
|
|
The most notable feature of USB OTG is support for a
|
||
|
|
"Dual-Role" device, which can act as either a device
|
||
|
|
or a host. The initial role choice can be changed
|
||
|
|
later, when two dual-role devices talk to each other.
|
||
|
|
|
||
|
|
At this writing, the OTG support in this driver is incomplete,
|
||
|
|
omitting the mandatory HNP or SRP protocols. However, some
|
||
|
|
of the cable based role switching works. (That is, grounding
|
||
|
|
the ID pin switches the controller to host mode, while leaving
|
||
|
|
it floating leaves it in peripheral mode.)
|
||
|
|
|
||
|
|
Select this if your system has a Mini-AB connector, or
|
||
|
|
to simplify certain kinds of configuration.
|
||
|
|
|
||
|
|
To implement your OTG Targeted Peripherals List (TPL), enable
|
||
|
|
USB_OTG_WHITELIST and update "drivers/usb/core/otg_whitelist.h"
|
||
|
|
to match your requirements.
|
||
|
|
|
||
|
|
endchoice
|
||
|
|
|
||
|
|
# enable peripheral support (including with OTG)
|
||
|
|
config USB_GADGET_MUSB_HDRC
|
||
|
|
bool
|
||
|
|
depends on USB_MUSB_HDRC && (USB_MUSB_PERIPHERAL || USB_MUSB_OTG)
|
||
|
|
# default y
|
||
|
|
# select USB_GADGET_DUALSPEED
|
||
|
|
# select USB_GADGET_SELECTED
|
||
|
|
|
||
|
|
# enables host support (including with OTG)
|
||
|
|
config USB_MUSB_HDRC_HCD
|
||
|
|
bool
|
||
|
|
depends on USB_MUSB_HDRC && (USB_MUSB_HOST || USB_MUSB_OTG)
|
||
|
|
select USB_OTG if USB_GADGET_MUSB_HDRC
|
||
|
|
default y
|
||
|
|
|
||
|
|
|
||
|
|
config MUSB_PIO_ONLY
|
||
|
|
bool 'Disable DMA (always use PIO)'
|
||
|
|
depends on USB_MUSB_HDRC
|
||
|
|
default y if USB_TUSB6010
|
||
|
|
help
|
||
|
|
All data is copied between memory and FIFO by the CPU.
|
||
|
|
DMA controllers are ignored.
|
||
|
|
|
||
|
|
Do not select 'n' here unless DMA support for your SOC or board
|
||
|
|
is unavailable (or unstable). When DMA is enabled at compile time,
|
||
|
|
you can still disable it at run time using the "use_dma=n" module
|
||
|
|
parameter.
|
||
|
|
|
||
|
|
config USB_INVENTRA_DMA
|
||
|
|
bool
|
||
|
|
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
|
||
|
|
default ARCH_OMAP2430 || ARCH_OMAP34XX || BLACKFIN
|
||
|
|
help
|
||
|
|
Enable DMA transfers using Mentor's engine.
|
||
|
|
|
||
|
|
config USB_TI_CPPI_DMA
|
||
|
|
bool
|
||
|
|
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
|
||
|
|
default ARCH_DAVINCI
|
||
|
|
help
|
||
|
|
Enable DMA transfers when TI CPPI DMA is available.
|
||
|
|
|
||
|
|
config USB_TUSB_OMAP_DMA
|
||
|
|
bool
|
||
|
|
depends on USB_MUSB_HDRC && !MUSB_PIO_ONLY
|
||
|
|
depends on USB_TUSB6010
|
||
|
|
depends on ARCH_OMAP
|
||
|
|
default y
|
||
|
|
help
|
||
|
|
Enable DMA transfers on TUSB 6010 when OMAP DMA is available.
|
||
|
|
|
||
|
|
config USB_MUSB_DEBUG
|
||
|
|
depends on USB_MUSB_HDRC
|
||
|
|
bool "Enable debugging messages"
|
||
|
|
default n
|
||
|
|
help
|
||
|
|
This enables musb debugging. To set the logging level use the debug
|
||
|
|
module parameter. Starting at level 3, per-transfer (urb, usb_request,
|
||
|
|
packet, or dma transfer) tracing may kick in.
|