2015-03-31 18:58:40 +02:00
|
|
|
This directory contains USB and flash firmware for
|
2015-03-31 18:50:27 +02:00
|
|
|
* Inverto IDL-400s
|
|
|
|
* Grundig GSS.BOX
|
|
|
|
* Inverto IDL-400S
|
|
|
|
|
|
|
|
Installation:
|
|
|
|
|
|
|
|
- setup a DHCP server for the box ethernet MAC address
|
|
|
|
- copy satip-axe-$(VERSION).usb as idl4k.scr (rename the file) to the USB stick
|
|
|
|
- copy satip-axe-$(VERSION).fw (no rename) to the USB stick
|
|
|
|
- both files should be in the root directory on the USB stick
|
|
|
|
- plug the USB stick to the upper USB port in box
|
|
|
|
- turn on the box
|
|
|
|
- the tuner LEDs must blink (Knight Rider effect) for few seconds
|
|
|
|
- box is accessible through telnet or ssh, IP address is obtained using DHCP
|
|
|
|
- the default login/password is root/satip
|
|
|
|
- the firmware is not written to the internal flash - when the USB stick
|
|
|
|
is not in the box, the original firmware will be booted
|
|
|
|
|
|
|
|
Installation to flash:
|
|
|
|
|
|
|
|
- WARNING! The original firmware will be overwritten!
|
|
|
|
- same steps, just replace satip-axe-$(VERSION).usb to satip-axe-$(VERSION).flash
|
|
|
|
- after boot of the new version, remove the USB stick to not write
|
|
|
|
the .fw file multiple times to flash (on each box start)
|
|
|
|
|
|
|
|
Customization:
|
|
|
|
|
|
|
|
- configuration file is in /etc/sysconfig/config
|
|
|
|
- localboot script can be in /etc/sysconfig/localboot
|
|
|
|
- passwd file is copied from /etc/sysconfig/passwd
|
|
|
|
- ssh authorized_keys file is copied from /etc/sysconfig/authorized_keys
|
|
|
|
|
|
|
|
Recovery of the original firmware:
|
|
|
|
|
|
|
|
- copy idl4k.recovery file as idl4k.scr file to the root directory on the USB stick
|
|
|
|
- plug the USB stick to the upper USB port in box
|
|
|
|
- turn on the box
|
|
|
|
- box is accessible through http (web browser) - original firmware
|
|
|
|
|
|
|
|
Notes:
|
|
|
|
|
|
|
|
- there is 128M SPI flash memory in the device
|
|
|
|
- 128k for u-boot (probably)
|
|
|
|
- 4M marked as system-nand0 (probably unused)
|
|
|
|
- the original firmware uses fw1-nand0 flash region (32M)
|
|
|
|
- the satip-axe firmware uses fw2-nand0 flash region (32M)
|
|
|
|
- data block is named data-nand0 - uses rest of flash
|
|
|
|
|
2015-03-31 18:54:38 +02:00
|
|
|
Disclaimer:
|
|
|
|
|
|
|
|
The SATIP AXE firmware is supplied "AS IS" without any warranties and
|
|
|
|
support.
|
|
|
|
|
|
|
|
The authors assumes no responsibility or liability for the use of
|
|
|
|
the software, conveys no license or title under any patent, copyright, or
|
|
|
|
mask work right to the product.
|
|
|
|
|
|
|
|
The authors reserve the right to make changes in the software
|
|
|
|
without notification. Authors also make no representation or
|
|
|
|
warranty that such software will be suitable for the specified use
|
|
|
|
without further testing or modification.
|
|
|
|
|
2015-03-31 18:50:27 +02:00
|
|
|
Bugs:
|
|
|
|
|
|
|
|
- the Inverto driver do not initialize properly sometimes
|
2015-04-06 19:05:07 +02:00
|
|
|
(minisatip is not started); if minisatip does not work,
|
|
|
|
you may check 'logread' for tuner initialization error (512)
|
|
|
|
or use 'dmesg' to check the lines bellow;
|
|
|
|
turn off the box for 5-30 minutes and try again...
|
2015-03-31 18:50:27 +02:00
|
|
|
|
|
|
|
demod900] setup [num_demods 4]
|
|
|
|
[pll6120] setup [num_plls:4] [clk:30000000] [bbgain:16]
|
|
|
|
[fe] Checking lut 0xC1ABEAF0
|
|
|
|
[fe] Checking lut 0xC1ABEB26
|
|
|
|
[fe] Checking lut 0xC1ABEAF0
|
|
|
|
[fe] Checking lut 0xC1ABEB54
|
|
|
|
[dmx] ... init 0
|
|
|
|
[dmx-ts] ... init 0
|
|
|
|
[i2c] I2C bus error /errno -121/!!
|
|
|
|
[i2c] I2C bus error /errno -121/!!
|
|
|
|
[i2c] I2C bus error /errno -121/!!
|
|
|
|
[pll6120] init error!
|
|
|
|
[fta_fe] FE Initialization done, res -1
|
|
|
|
|
|
|
|
- reboot command cannot be used (uboot usb init fails, hw init fails)
|
|
|
|
|
|
|
|
History:
|
|
|
|
|
2015-04-06 19:05:07 +02:00
|
|
|
satip-axe-201504061852-2 : Mon Apr 6 2015
|
|
|
|
- minisatip fixes (unicable, multiple tuners, h/v and lo/hi setup)
|
|
|
|
- load axe modules in rcSBB
|
|
|
|
|
2015-03-31 18:58:40 +02:00
|
|
|
satip-axe-201503311856-1 : Tue Mar 31 2015
|
|
|
|
- initial firmware release
|