satip-axe/kernel/include/linux/stm/ssc.h

144 lines
4.4 KiB
C
Raw Normal View History

/*
* --------------------------------------------------------------------------
*
* ssc.h
* define and struct for STMicroelectronics SSC device
*
* --------------------------------------------------------------------------
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
* --------------------------------------------------------------------------
*/
#ifndef STM_SSC_H
#define STM_SSC_H 1
/* SSC Baud Rate generator */
#define SSC_BRG 0x0
/* SSC Transmitter Buffer */
#define SSC_TBUF 0x4
/* SSC Receive Buffer */
#define SSC_RBUF 0x8
/*SSC Control */
#define SSC_CTL 0xC
#define SSC_CTL_DATA_WIDTH_9 0x8
#define SSC_CTL_BM 0xf
#define SSC_CTL_HB 0x10
#define SSC_CTL_PH 0x20
#define SSC_CTL_PO 0x40
#define SSC_CTL_SR 0x80
#define SSC_CTL_MS 0x100
#define SSC_CTL_EN 0x200
#define SSC_CTL_LPB 0x400
#define SSC_CTL_EN_TX_FIFO 0x800
#define SSC_CTL_EN_RX_FIFO 0x1000
#define SSC_CTL_EN_CLST_RX 0x2000
/* SSC Interrupt Enable */
#define SSC_IEN 0x10
#define SSC_IEN_RIEN 0x1
#define SSC_IEN_TIEN 0x2
#define SSC_IEN_TEEN 0x4
#define SSC_IEN_REEN 0x8
#define SSC_IEN_PEEN 0x10
#define SSC_IEN_AASEN 0x40
#define SSC_IEN_STOPEN 0x80
#define SSC_IEN_ARBLEN 0x100
#define SSC_IEN_NACKEN 0x400
#define SSC_IEN_REPSTRTEN 0x800
#define SSC_IEN_TX_FIFO_HALF 0x1000
#define SSC_IEN_RX_FIFO_HALF_FULL 0x4000
/* SSC Status */
#define SSC_STA 0x14
#define SSC_STA_RIR 0x1
#define SSC_STA_TIR 0x2
#define SSC_STA_TE 0x4
#define SSC_STA_RE 0x8
#define SSC_STA_PE 0x10
#define SSC_STA_CLST 0x20
#define SSC_STA_AAS 0x40
#define SSC_STA_STOP 0x80
#define SSC_STA_ARBL 0x100
#define SSC_STA_BUSY 0x200
#define SSC_STA_NACK 0x400
#define SSC_STA_REPSTRT 0x800
#define SSC_STA_TX_FIFO_HALF 0x1000
#define SSC_STA_TX_FIFO_FULL 0x2000
#define SSC_STA_RX_FIFO_HALF 0x4000
/*SSC I2C Control */
#define SSC_I2C 0x18
#define SSC_I2C_I2CM 0x1
#define SSC_I2C_STRTG 0x2
#define SSC_I2C_STOPG 0x4
#define SSC_I2C_ACKG 0x8
#define SSC_I2C_AD10 0x10
#define SSC_I2C_TXENB 0x20
#define SSC_I2C_REPSTRTG 0x800
#define SSC_I2C_I2CFSMODE 0x1000
/* SSC Slave Address */
#define SSC_SLAD 0x1C
/* SSC I2C bus repeated start hold time */
#define SSC_REP_START_HOLD 0x20
/* SSC I2C bus start hold time */
#define SSC_START_HOLD 0x24
/* SSC I2C bus repeated start setup time */
#define SSC_REP_START_SETUP 0x28
/* SSC I2C bus repeated stop setup time */
#define SSC_DATA_SETUP 0x2C
/* SSC I2C bus stop setup time */
#define SSC_STOP_SETUP 0x30
/* SSC I2C bus free time */
#define SSC_BUS_FREE 0x34
/* SSC Tx FIFO Status */
#define SSC_TX_FSTAT 0x38
#define SSC_TX_FSTAT_STATUS 0x07
/* SSC Rx FIFO Status */
#define SSC_RX_FSTAT 0x3C
#define SSC_RX_FSTAT_STATUS 0x07
/* SSC Prescaler value value for clock */
#define SSC_PRE_SCALER_BRG 0x40
/* SSC Clear bit operation */
#define SSC_CLR 0x80
#define SSC_CLR_SSCAAS 0x40
#define SSC_CLR_SSCSTOP 0x80
#define SSC_CLR_SSCARBL 0x100
#define SSC_CLR_NACK 0x400
#define SSC_CLR_REPSTRT 0x800
/* SSC Noise suppression Width */
#define SSC_NOISE_SUPP_WIDTH 0x100
/* SSC Clock Prescaler */
#define SSC_PRSCALER 0x104
#define SSC_PRSC_VALUE 0x0f
/* SSC Noise suppression Width dataout */
#define SSC_NOISE_SUPP_WIDTH_DATAOUT 0x108
/* SSC Prescaler for delay in dataout */
#define SSC_PRSCALER_DATAOUT 0x10c
#define SSC_TXFIFO_SIZE 0x8
#define SSC_RXFIFO_SIZE 0x8
/* Use the following macros to access SSC I/O memory */
#define ssc_store32(ssc, offset, value) iowrite32(value, ssc->base+offset)
#define ssc_store16(ssc, offset, value) iowrite16(value, ssc->base+offset)
#define ssc_store8(ssc, offset, value) iowrite8(value, ssc->base+offset)
#define ssc_load32(ssc, offset) ioread32(ssc->base+offset)
#define ssc_load16(ssc, offset) ioread16(ssc->base+offset)
#define ssc_load8(ssc, offset) XSioread8(ssc->base+offset)
#endif /* STM_SSC_H */