add idl4k kernel firmware version 1.13.0.105

kernel/arch/arm/mach-s3c2440/Kconfig

@@ -0,0 +1,112 @@
+# arch/arm/mach-s3c2440/Kconfig
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config CPU_S3C2440
+	bool
+	depends on ARCH_S3C2410
+	select CPU_ARM920T
+	select S3C2410_CLOCK
+	select S3C2410_PM if PM
+	select S3C2410_GPIO
+	select S3C2440_DMA if S3C2410_DMA
+	select CPU_S3C244X
+	select CPU_LLSERIAL_S3C2440
+	help
+	  Support for S3C2440 Samsung Mobile CPU based systems.
+
+config S3C2440_DMA
+	bool
+	depends on ARCH_S3C2410 && CPU_S3C24405B
+	help
+	  Support for S3C2440 specific DMA code5A
+
+
+menu "S3C2440 Machines"
+
+config MACH_ANUBIS
+	bool "Simtec Electronics ANUBIS"
+	select CPU_S3C2440
+	select S3C24XX_DCLK
+	select PM_SIMTEC if PM
+	select HAVE_PATA_PLATFORM
+	select S3C24XX_GPIO_EXTRA64
+	select S3C2440_XTAL_12000000
+	select S3C_DEV_USB_HOST
+	help
+	  Say Y here if you are using the Simtec Electronics ANUBIS
+	  development system
+
+config MACH_OSIRIS
+	bool "Simtec IM2440D20 (OSIRIS) module"
+	select CPU_S3C2440
+	select S3C24XX_DCLK
+	select PM_SIMTEC if PM
+	select S3C24XX_GPIO_EXTRA128
+	select S3C2440_XTAL_12000000
+	select S3C2410_IOTIMING if S3C2440_CPUFREQ
+	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
+	help
+	  Say Y here if you are using the Simtec IM2440D20 module, also
+	  known as the Osiris.
+
+config MACH_RX3715
+	bool "HP iPAQ rx3715"
+	select CPU_S3C2440
+	select S3C2440_XTAL_16934400
+	select PM_H1940 if PM
+	select S3C_DEV_NAND
+	help
+	  Say Y here if you are using the HP iPAQ rx3715.
+
+config ARCH_S3C2440
+	bool "SMDK2440"
+	select CPU_S3C2440
+	select S3C2440_XTAL_16934400
+	select MACH_SMDK
+	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
+	help
+	  Say Y here if you are using the SMDK2440.
+
+config MACH_NEXCODER_2440
+ 	bool "NexVision NEXCODER 2440 Light Board"
+ 	select CPU_S3C2440
+	select S3C2440_XTAL_12000000
+	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
+	help
+ 	  Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
+
+config SMDK2440_CPU2440
+	bool "SMDK2440 with S3C2440 CPU module"
+	depends on ARCH_S3C2440
+	default y if ARCH_S3C2440
+	select S3C2440_XTAL_16934400
+	select CPU_S3C2440
+
+config MACH_AT2440EVB
+	bool "Avantech AT2440EVB development board"
+	select CPU_S3C2440
+	select S3C_DEV_USB_HOST
+	select S3C_DEV_NAND
+	help
+	  Say Y here if you are using the AT2440EVB development board
+
+config MACH_MINI2440
+	bool "MINI2440 development board"
+	select CPU_S3C2440
+	select EEPROM_AT24
+	select LEDS_TRIGGER_BACKLIGHT
+	select SND_S3C24XX_SOC_S3C24XX_UDA134X
+	select S3C_DEV_NAND
+	select S3C_DEV_USB_HOST
+	help
+	  Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
+	  available via various sources. It can come with a 3.5" or 7" touch LCD.
+
+endmenu
+

kernel/arch/arm/mach-s3c2440/Makefile

@@ -0,0 +1,25 @@
+# arch/arm/mach-s3c2440/Makefile
+#
+# Copyright 2007 Simtec Electronics
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+obj-$(CONFIG_CPU_S3C2440)	+= s3c2440.o dsc.o
+obj-$(CONFIG_CPU_S3C2440)	+= irq.o
+obj-$(CONFIG_CPU_S3C2440)	+= clock.o
+obj-$(CONFIG_S3C2440_DMA)	+= dma.o
+
+# Machine support
+
+obj-$(CONFIG_MACH_ANUBIS)	+= mach-anubis.o
+obj-$(CONFIG_MACH_OSIRIS)	+= mach-osiris.o
+obj-$(CONFIG_MACH_RX3715)	+= mach-rx3715.o
+obj-$(CONFIG_ARCH_S3C2440)	+= mach-smdk2440.o
+obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
+obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
+obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o

kernel/arch/arm/mach-s3c2440/clock.c

@@ -0,0 +1,150 @@
+/* linux/arch/arm/mach-s3c2440/clock.c
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2440 Clock support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/device.h>
+#include <linux/sysdev.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <asm/atomic.h>
+#include <asm/irq.h>
+
+#include <mach/regs-clock.h>
+
+#include <plat/clock.h>
+#include <plat/cpu.h>
+
+/* S3C2440 extended clock support */
+
+static unsigned long s3c2440_camif_upll_round(struct clk *clk,
+					      unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	int div;
+
+	if (rate > parent_rate)
+		return parent_rate;
+
+	/* note, we remove the +/- 1 calculations for the divisor */
+
+	div = (parent_rate / rate) / 2;
+
+	if (div < 1)
+		div = 1;
+	else if (div > 16)
+		div = 16;
+
+	return parent_rate / (div * 2);
+}
+
+static int s3c2440_camif_upll_setrate(struct clk *clk, unsigned long rate)
+{
+	unsigned long parent_rate = clk_get_rate(clk->parent);
+	unsigned long camdivn =  __raw_readl(S3C2440_CAMDIVN);
+
+	rate = s3c2440_camif_upll_round(clk, rate);
+
+	camdivn &= ~(S3C2440_CAMDIVN_CAMCLK_SEL | S3C2440_CAMDIVN_CAMCLK_MASK);
+
+	if (rate != parent_rate) {
+		camdivn |= S3C2440_CAMDIVN_CAMCLK_SEL;
+		camdivn |= (((parent_rate / rate) / 2) - 1);
+	}
+
+	__raw_writel(camdivn, S3C2440_CAMDIVN);
+
+	return 0;
+}
+
+/* Extra S3C2440 clocks */
+
+static struct clk s3c2440_clk_cam = {
+	.name		= "camif",
+	.id		= -1,
+	.enable		= s3c2410_clkcon_enable,
+	.ctrlbit	= S3C2440_CLKCON_CAMERA,
+};
+
+static struct clk s3c2440_clk_cam_upll = {
+	.name		= "camif-upll",
+	.id		= -1,
+	.set_rate	= s3c2440_camif_upll_setrate,
+	.round_rate	= s3c2440_camif_upll_round,
+};
+
+static struct clk s3c2440_clk_ac97 = {
+	.name		= "ac97",
+	.id		= -1,
+	.enable		= s3c2410_clkcon_enable,
+	.ctrlbit	= S3C2440_CLKCON_CAMERA,
+};
+
+static int s3c2440_clk_add(struct sys_device *sysdev)
+{
+	struct clk *clock_upll;
+	struct clk *clock_h;
+	struct clk *clock_p;
+
+	clock_p = clk_get(NULL, "pclk");
+	clock_h = clk_get(NULL, "hclk");
+	clock_upll = clk_get(NULL, "upll");
+
+	if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) {
+		printk(KERN_ERR "S3C2440: Failed to get parent clocks\n");
+		return -EINVAL;
+	}
+
+	s3c2440_clk_cam.parent = clock_h;
+	s3c2440_clk_ac97.parent = clock_p;
+	s3c2440_clk_cam_upll.parent = clock_upll;
+
+	s3c24xx_register_clock(&s3c2440_clk_ac97);
+	s3c24xx_register_clock(&s3c2440_clk_cam);
+	s3c24xx_register_clock(&s3c2440_clk_cam_upll);
+
+	clk_disable(&s3c2440_clk_ac97);
+	clk_disable(&s3c2440_clk_cam);
+
+	return 0;
+}
+
+static struct sysdev_driver s3c2440_clk_driver = {
+	.add	= s3c2440_clk_add,
+};
+
+static __init int s3c24xx_clk_driver(void)
+{
+	return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_clk_driver);
+}
+
+arch_initcall(s3c24xx_clk_driver);

kernel/arch/arm/mach-s3c2440/dma.c

@@ -0,0 +1,211 @@
+/* linux/arch/arm/mach-s3c2440/dma.c
+ *
+ * Copyright (c) 2006 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2440 DMA selection
+ *
+ * http://armlinux.simtec.co.uk/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sysdev.h>
+#include <linux/serial_core.h>
+
+#include <mach/map.h>
+#include <mach/dma.h>
+
+#include <plat/dma-plat.h>
+#include <plat/cpu.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <plat/regs-ac97.h>
+#include <plat/regs-dma.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/regs-sdi.h>
+#include <plat/regs-iis.h>
+#include <plat/regs-spi.h>
+
+static struct s3c24xx_dma_map __initdata s3c2440_dma_mappings[] = {
+	[DMACH_XD0] = {
+		.name		= "xdreq0",
+		.channels[0]	= S3C2410_DCON_CH0_XDREQ0 | DMA_CH_VALID,
+	},
+	[DMACH_XD1] = {
+		.name		= "xdreq1",
+		.channels[1]	= S3C2410_DCON_CH1_XDREQ1 | DMA_CH_VALID,
+	},
+	[DMACH_SDI] = {
+		.name		= "sdi",
+		.channels[0]	= S3C2410_DCON_CH0_SDI | DMA_CH_VALID,
+		.channels[1]	= S3C2440_DCON_CH1_SDI | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_SDI | DMA_CH_VALID,
+		.channels[3]	= S3C2410_DCON_CH3_SDI | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_SPI0] = {
+		.name		= "spi0",
+		.channels[1]	= S3C2410_DCON_CH1_SPI | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_SPI + S3C2410_SPTDAT,
+		.hw_addr.from	= S3C2410_PA_SPI + S3C2410_SPRDAT,
+	},
+	[DMACH_SPI1] = {
+		.name		= "spi1",
+		.channels[3]	= S3C2410_DCON_CH3_SPI | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_SPI + 0x20 + S3C2410_SPTDAT,
+		.hw_addr.from	= S3C2410_PA_SPI + 0x20 + S3C2410_SPRDAT,
+	},
+	[DMACH_UART0] = {
+		.name		= "uart0",
+		.channels[0]	= S3C2410_DCON_CH0_UART0 | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_UART0 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART0 + S3C2410_URXH,
+	},
+	[DMACH_UART1] = {
+		.name		= "uart1",
+		.channels[1]	= S3C2410_DCON_CH1_UART1 | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_UART1 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART1 + S3C2410_URXH,
+	},
+      	[DMACH_UART2] = {
+		.name		= "uart2",
+		.channels[3]	= S3C2410_DCON_CH3_UART2 | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_UART2 + S3C2410_UTXH,
+		.hw_addr.from	= S3C2410_PA_UART2 + S3C2410_URXH,
+	},
+	[DMACH_TIMER] = {
+		.name		= "timer",
+		.channels[0]	= S3C2410_DCON_CH0_TIMER | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_TIMER | DMA_CH_VALID,
+		.channels[3]	= S3C2410_DCON_CH3_TIMER | DMA_CH_VALID,
+	},
+	[DMACH_I2S_IN] = {
+		.name		= "i2s-sdi",
+		.channels[1]	= S3C2410_DCON_CH1_I2SSDI | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_I2SSDI | DMA_CH_VALID,
+		.hw_addr.from	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_I2S_OUT] = {
+		.name		= "i2s-sdo",
+		.channels[0]	= S3C2440_DCON_CH0_I2SSDO | DMA_CH_VALID,
+		.channels[2]	= S3C2410_DCON_CH2_I2SSDO | DMA_CH_VALID,
+		.hw_addr.to	= S3C2410_PA_IIS + S3C2410_IISFIFO,
+	},
+	[DMACH_PCM_IN] = {
+		.name		= "pcm-in",
+		.channels[0]	= S3C2440_DCON_CH0_PCMIN | DMA_CH_VALID,
+		.channels[2]	= S3C2440_DCON_CH2_PCMIN | DMA_CH_VALID,
+		.hw_addr.from	= S3C2440_PA_AC97 + S3C_AC97_PCM_DATA,
+	},
+	[DMACH_PCM_OUT] = {
+		.name		= "pcm-out",
+		.channels[1]	= S3C2440_DCON_CH1_PCMOUT | DMA_CH_VALID,
+		.channels[3]	= S3C2440_DCON_CH3_PCMOUT | DMA_CH_VALID,
+		.hw_addr.to	= S3C2440_PA_AC97 + S3C_AC97_PCM_DATA,
+	},
+	[DMACH_MIC_IN] = {
+		.name		= "mic-in",
+		.channels[2]	= S3C2440_DCON_CH2_MICIN | DMA_CH_VALID,
+		.channels[3]	= S3C2440_DCON_CH3_MICIN | DMA_CH_VALID,
+		.hw_addr.from	= S3C2440_PA_AC97 + S3C_AC97_MIC_DATA,
+	},
+	[DMACH_USB_EP1] = {
+		.name		= "usb-ep1",
+		.channels[0]	= S3C2410_DCON_CH0_USBEP1 | DMA_CH_VALID,
+	},
+	[DMACH_USB_EP2] = {
+		.name		= "usb-ep2",
+		.channels[1]	= S3C2410_DCON_CH1_USBEP2 | DMA_CH_VALID,
+	},
+	[DMACH_USB_EP3] = {
+		.name		= "usb-ep3",
+		.channels[2]	= S3C2410_DCON_CH2_USBEP3 | DMA_CH_VALID,
+	},
+	[DMACH_USB_EP4] = {
+		.name		= "usb-ep4",
+		.channels[3]	= S3C2410_DCON_CH3_USBEP4 | DMA_CH_VALID,
+	},
+};
+
+static void s3c2440_dma_select(struct s3c2410_dma_chan *chan,
+			       struct s3c24xx_dma_map *map)
+{
+	chan->dcon = map->channels[chan->number] & ~DMA_CH_VALID;
+}
+
+static struct s3c24xx_dma_selection __initdata s3c2440_dma_sel = {
+	.select		= s3c2440_dma_select,
+	.dcon_mask	= 7 << 24,
+	.map		= s3c2440_dma_mappings,
+	.map_size	= ARRAY_SIZE(s3c2440_dma_mappings),
+};
+
+static struct s3c24xx_dma_order __initdata s3c2440_dma_order = {
+	.channels	= {
+		[DMACH_SDI]	= {
+			.list	= {
+				[0]	= 3 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+				[2]	= 1 | DMA_CH_VALID,
+				[3]	= 0 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_I2S_IN]	= {
+			.list	= {
+				[0]	= 1 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_I2S_OUT]	= {
+			.list	= {
+				[0]	= 2 | DMA_CH_VALID,
+				[1]	= 1 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_PCM_IN] = {
+			.list	= {
+				[0]	= 2 | DMA_CH_VALID,
+				[1]	= 1 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_PCM_OUT] = {
+			.list	= {
+				[0]	= 1 | DMA_CH_VALID,
+				[1]	= 3 | DMA_CH_VALID,
+			},
+		},
+		[DMACH_MIC_IN] = {
+			.list	= {
+				[0]	= 3 | DMA_CH_VALID,
+				[1]	= 2 | DMA_CH_VALID,
+			},
+		},
+	},
+};
+
+static int __init s3c2440_dma_add(struct sys_device *sysdev)
+{
+	s3c2410_dma_init();
+	s3c24xx_dma_order_set(&s3c2440_dma_order);
+	return s3c24xx_dma_init_map(&s3c2440_dma_sel);
+}
+
+static struct sysdev_driver s3c2440_dma_driver = {
+	.add	= s3c2440_dma_add,
+};
+
+static int __init s3c2440_dma_init(void)
+{
+	return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_dma_driver);
+}
+
+arch_initcall(s3c2440_dma_init);
+

kernel/arch/arm/mach-s3c2440/dsc.c

@@ -0,0 +1,54 @@
+/* linux/arch/arm/mach-s3c2440/dsc.c
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *   Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C2440 Drive Strength Control support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <mach/regs-gpio.h>
+#include <mach/regs-dsc.h>
+
+#include <plat/cpu.h>
+#include <plat/s3c2440.h>
+
+int s3c2440_set_dsc(unsigned int pin, unsigned int value)
+{
+	void __iomem *base;
+	unsigned long val;
+	unsigned long flags;
+	unsigned long mask;
+
+	base = (pin & S3C2440_SELECT_DSC1) ? S3C2440_DSC1 : S3C2440_DSC0;
+	mask = 3 << S3C2440_DSC_GETSHIFT(pin);
+
+	local_irq_save(flags);
+
+	val = __raw_readl(base);
+	val &= ~mask;
+	val |= value & mask;
+	__raw_writel(val, base);
+
+	local_irq_restore(flags);
+	return 0;
+}
+
+EXPORT_SYMBOL(s3c2440_set_dsc);

kernel/arch/arm/mach-s3c2440/irq.c

@@ -0,0 +1,126 @@
+/* linux/arch/arm/mach-s3c2440/irq.c
+ *
+ * Copyright (c) 2003,2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/sysdev.h>
+#include <linux/io.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <asm/mach/irq.h>
+
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
+
+#include <plat/cpu.h>
+#include <plat/pm.h>
+#include <plat/irq.h>
+
+/* WDT/AC97 */
+
+static void s3c_irq_demux_wdtac97(unsigned int irq,
+				  struct irq_desc *desc)
+{
+	unsigned int subsrc, submsk;
+
+	/* read the current pending interrupts, and the mask
+	 * for what it is available */
+
+	subsrc = __raw_readl(S3C2410_SUBSRCPND);
+	submsk = __raw_readl(S3C2410_INTSUBMSK);
+
+	subsrc &= ~submsk;
+	subsrc >>= 13;
+	subsrc &= 3;
+
+	if (subsrc != 0) {
+		if (subsrc & 1) {
+			generic_handle_irq(IRQ_S3C2440_WDT);
+		}
+		if (subsrc & 2) {
+			generic_handle_irq(IRQ_S3C2440_AC97);
+		}
+	}
+}
+
+
+#define INTMSK_WDT	 (1UL << (IRQ_WDT - IRQ_EINT0))
+
+static void
+s3c_irq_wdtac97_mask(unsigned int irqno)
+{
+	s3c_irqsub_mask(irqno, INTMSK_WDT, 3<<13);
+}
+
+static void
+s3c_irq_wdtac97_unmask(unsigned int irqno)
+{
+	s3c_irqsub_unmask(irqno, INTMSK_WDT);
+}
+
+static void
+s3c_irq_wdtac97_ack(unsigned int irqno)
+{
+	s3c_irqsub_maskack(irqno, INTMSK_WDT, 3<<13);
+}
+
+static struct irq_chip s3c_irq_wdtac97 = {
+	.mask	    = s3c_irq_wdtac97_mask,
+	.unmask	    = s3c_irq_wdtac97_unmask,
+	.ack	    = s3c_irq_wdtac97_ack,
+};
+
+static int s3c2440_irq_add(struct sys_device *sysdev)
+{
+	unsigned int irqno;
+
+	printk("S3C2440: IRQ Support\n");
+
+	/* add new chained handler for wdt, ac7 */
+
+	set_irq_chip(IRQ_WDT, &s3c_irq_level_chip);
+	set_irq_handler(IRQ_WDT, handle_level_irq);
+	set_irq_chained_handler(IRQ_WDT, s3c_irq_demux_wdtac97);
+
+	for (irqno = IRQ_S3C2440_WDT; irqno <= IRQ_S3C2440_AC97; irqno++) {
+		set_irq_chip(irqno, &s3c_irq_wdtac97);
+		set_irq_handler(irqno, handle_level_irq);
+		set_irq_flags(irqno, IRQF_VALID);
+	}
+
+	return 0;
+}
+
+static struct sysdev_driver s3c2440_irq_driver = {
+	.add		= s3c2440_irq_add,
+};
+
+static int s3c2440_irq_init(void)
+{
+	return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_irq_driver);
+}
+
+arch_initcall(s3c2440_irq_init);
+

kernel/arch/arm/mach-s3c2440/mach-anubis.c

@@ -0,0 +1,495 @@
+/* linux/arch/arm/mach-s3c2440/mach-anubis.c
+ *
+ * Copyright (c) 2003-2005,2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/sm501.h>
+#include <linux/sm501-regs.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/anubis-map.h>
+#include <mach/anubis-irq.h>
+#include <mach/anubis-cpld.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <plat/nand.h>
+#include <plat/iic.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <net/ax88796.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#define COPYRIGHT ", (c) 2005 Simtec Electronics"
+
+static struct map_desc anubis_iodesc[] __initdata = {
+  /* ISA IO areas */
+
+  {
+	.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
+	.pfn		= __phys_to_pfn(0x0),
+	.length		= SZ_4M,
+	.type		= MT_DEVICE,
+  }, {
+	.virtual	= (u32)S3C24XX_VA_ISA_WORD,
+	.pfn		= __phys_to_pfn(0x0),
+	.length 	= SZ_4M,
+	.type		= MT_DEVICE,
+  },
+
+  /* we could possibly compress the next set down into a set of smaller tables
+   * pagetables, but that would mean using an L2 section, and it still means
+   * we cannot actually feed the same register to an LDR due to 16K spacing
+   */
+
+  /* CPLD control registers */
+
+  {
+	.virtual	= (u32)ANUBIS_VA_CTRL1,
+	.pfn		= __phys_to_pfn(ANUBIS_PA_CTRL1),
+	.length		= SZ_4K,
+	.type		= MT_DEVICE,
+  }, {
+	.virtual	= (u32)ANUBIS_VA_IDREG,
+	.pfn		= __phys_to_pfn(ANUBIS_PA_IDREG),
+	.length		= SZ_4K,
+	.type		= MT_DEVICE,
+  },
+};
+
+#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = {
+	[0] = {
+		.name		= "uclk",
+		.divisor	= 1,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	},
+	[1] = {
+		.name		= "pclk",
+		.divisor	= 1,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	}
+};
+
+
+static struct s3c2410_uartcfg anubis_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = anubis_serial_clocks,
+		.clocks_size = ARRAY_SIZE(anubis_serial_clocks),
+	},
+	[1] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = anubis_serial_clocks,
+		.clocks_size = ARRAY_SIZE(anubis_serial_clocks),
+	},
+};
+
+/* NAND Flash on Anubis board */
+
+static int external_map[]   = { 2 };
+static int chip0_map[]      = { 0 };
+static int chip1_map[]      = { 1 };
+
+static struct mtd_partition anubis_default_nand_part[] = {
+	[0] = {
+		.name	= "Boot Agent",
+		.size	= SZ_16K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "/boot",
+		.size	= SZ_4M - SZ_16K,
+		.offset	= SZ_16K,
+	},
+	[2] = {
+		.name	= "user1",
+		.offset	= SZ_4M,
+		.size	= SZ_32M - SZ_4M,
+	},
+	[3] = {
+		.name	= "user2",
+		.offset	= SZ_32M,
+		.size	= MTDPART_SIZ_FULL,
+	}
+};
+
+static struct mtd_partition anubis_default_nand_part_large[] = {
+	[0] = {
+		.name	= "Boot Agent",
+		.size	= SZ_128K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "/boot",
+		.size	= SZ_4M - SZ_128K,
+		.offset	= SZ_128K,
+	},
+	[2] = {
+		.name	= "user1",
+		.offset	= SZ_4M,
+		.size	= SZ_32M - SZ_4M,
+	},
+	[3] = {
+		.name	= "user2",
+		.offset	= SZ_32M,
+		.size	= MTDPART_SIZ_FULL,
+	}
+};
+
+/* the Anubis has 3 selectable slots for nand-flash, the two
+ * on-board chip areas, as well as the external slot.
+ *
+ * Note, there is no current hot-plug support for the External
+ * socket.
+*/
+
+static struct s3c2410_nand_set anubis_nand_sets[] = {
+	[1] = {
+		.name		= "External",
+		.nr_chips	= 1,
+		.nr_map		= external_map,
+		.nr_partitions	= ARRAY_SIZE(anubis_default_nand_part),
+		.partitions	= anubis_default_nand_part,
+	},
+	[0] = {
+		.name		= "chip0",
+		.nr_chips	= 1,
+		.nr_map		= chip0_map,
+		.nr_partitions	= ARRAY_SIZE(anubis_default_nand_part),
+		.partitions	= anubis_default_nand_part,
+	},
+	[2] = {
+		.name		= "chip1",
+		.nr_chips	= 1,
+		.nr_map		= chip1_map,
+		.nr_partitions	= ARRAY_SIZE(anubis_default_nand_part),
+		.partitions	= anubis_default_nand_part,
+	},
+};
+
+static void anubis_nand_select(struct s3c2410_nand_set *set, int slot)
+{
+	unsigned int tmp;
+
+	slot = set->nr_map[slot] & 3;
+
+	pr_debug("anubis_nand: selecting slot %d (set %p,%p)\n",
+		 slot, set, set->nr_map);
+
+	tmp = __raw_readb(ANUBIS_VA_CTRL1);
+	tmp &= ~ANUBIS_CTRL1_NANDSEL;
+	tmp |= slot;
+
+	pr_debug("anubis_nand: ctrl1 now %02x\n", tmp);
+
+	__raw_writeb(tmp, ANUBIS_VA_CTRL1);
+}
+
+static struct s3c2410_platform_nand anubis_nand_info = {
+	.tacls		= 25,
+	.twrph0		= 55,
+	.twrph1		= 40,
+	.nr_sets	= ARRAY_SIZE(anubis_nand_sets),
+	.sets		= anubis_nand_sets,
+	.select_chip	= anubis_nand_select,
+};
+
+/* IDE channels */
+
+static struct pata_platform_info anubis_ide_platdata = {
+	.ioport_shift	= 5,
+};
+
+static struct resource anubis_ide0_resource[] = {
+	{
+		.start	= S3C2410_CS3,
+		.end	= S3C2410_CS3 + (8*32) - 1,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= S3C2410_CS3 + (1<<26) + (6*32),
+		.end	= S3C2410_CS3 + (1<<26) + (7*32) - 1,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_IDE0,
+		.end	= IRQ_IDE0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device anubis_device_ide0 = {
+	.name		= "pata_platform",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(anubis_ide0_resource),
+	.resource	= anubis_ide0_resource,
+	.dev	= {
+		.platform_data = &anubis_ide_platdata,
+		.coherent_dma_mask = ~0,
+	},
+};
+
+static struct resource anubis_ide1_resource[] = {
+	{
+		.start	= S3C2410_CS4,
+		.end	= S3C2410_CS4 + (8*32) - 1,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= S3C2410_CS4 + (1<<26) + (6*32),
+		.end	= S3C2410_CS4 + (1<<26) + (7*32) - 1,
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.start	= IRQ_IDE0,
+		.end	= IRQ_IDE0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device anubis_device_ide1 = {
+	.name		= "pata_platform",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(anubis_ide1_resource),
+	.resource	= anubis_ide1_resource,
+	.dev	= {
+		.platform_data = &anubis_ide_platdata,
+		.coherent_dma_mask = ~0,
+	},
+};
+
+/* Asix AX88796 10/100 ethernet controller */
+
+static struct ax_plat_data anubis_asix_platdata = {
+	.flags		= AXFLG_MAC_FROMDEV,
+	.wordlength	= 2,
+	.dcr_val	= 0x48,
+	.rcr_val	= 0x40,
+};
+
+static struct resource anubis_asix_resource[] = {
+	[0] = {
+		.start = S3C2410_CS5,
+		.end   = S3C2410_CS5 + (0x20 * 0x20) -1,
+		.flags = IORESOURCE_MEM
+	},
+	[1] = {
+		.start = IRQ_ASIX,
+		.end   = IRQ_ASIX,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device anubis_device_asix = {
+	.name		= "ax88796",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(anubis_asix_resource),
+	.resource	= anubis_asix_resource,
+	.dev		= {
+		.platform_data = &anubis_asix_platdata,
+	}
+};
+
+/* SM501 */
+
+static struct resource anubis_sm501_resource[] = {
+	[0] = {
+		.start	= S3C2410_CS2,
+		.end	= S3C2410_CS2 + SZ_8M,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= S3C2410_CS2 + SZ_64M - SZ_2M,
+		.end	= S3C2410_CS2 + SZ_64M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= IRQ_EINT0,
+		.end	= IRQ_EINT0,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct sm501_initdata anubis_sm501_initdata = {
+	.gpio_high	= {
+		.set	= 0x3F000000,		/* 24bit panel */
+		.mask	= 0x0,
+	},
+	.misc_timing	= {
+		.set	= 0x010100,		/* SDRAM timing */
+		.mask	= 0x1F1F00,
+	},
+	.misc_control	= {
+		.set	= SM501_MISC_PNL_24BIT,
+		.mask	= 0,
+	},
+
+	.devices	= SM501_USE_GPIO,
+
+	/* set the SDRAM and bus clocks */
+	.mclk		= 72 * MHZ,
+	.m1xclk		= 144 * MHZ,
+};
+
+static struct sm501_platdata_gpio_i2c anubis_sm501_gpio_i2c[] = {
+	[0] = {
+		.bus_num	= 1,
+		.pin_scl	= 44,
+		.pin_sda	= 45,
+	},
+	[1] = {
+		.bus_num	= 2,
+		.pin_scl	= 40,
+		.pin_sda	= 41,
+	},
+};
+
+static struct sm501_platdata anubis_sm501_platdata = {
+	.init		= &anubis_sm501_initdata,
+	.gpio_base	= -1,
+	.gpio_i2c	= anubis_sm501_gpio_i2c,
+	.gpio_i2c_nr	= ARRAY_SIZE(anubis_sm501_gpio_i2c),
+};
+
+static struct platform_device anubis_device_sm501 = {
+	.name		= "sm501",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(anubis_sm501_resource),
+	.resource	= anubis_sm501_resource,
+	.dev		= {
+		.platform_data = &anubis_sm501_platdata,
+	},
+};
+
+/* Standard Anubis devices */
+
+static struct platform_device *anubis_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_wdt,
+	&s3c_device_adc,
+	&s3c_device_i2c0,
+ 	&s3c_device_rtc,
+	&s3c_device_nand,
+	&anubis_device_ide0,
+	&anubis_device_ide1,
+	&anubis_device_asix,
+	&anubis_device_sm501,
+};
+
+static struct clk *anubis_clocks[] __initdata = {
+	&s3c24xx_dclk0,
+	&s3c24xx_dclk1,
+	&s3c24xx_clkout0,
+	&s3c24xx_clkout1,
+	&s3c24xx_uclk,
+};
+
+/* I2C devices. */
+
+static struct i2c_board_info anubis_i2c_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("tps65011", 0x48),
+		.irq	= IRQ_EINT20,
+	}
+};
+
+static void __init anubis_map_io(void)
+{
+	/* initialise the clocks */
+
+	s3c24xx_dclk0.parent = &clk_upll;
+	s3c24xx_dclk0.rate   = 12*1000*1000;
+
+	s3c24xx_dclk1.parent = &clk_upll;
+	s3c24xx_dclk1.rate   = 24*1000*1000;
+
+	s3c24xx_clkout0.parent  = &s3c24xx_dclk0;
+	s3c24xx_clkout1.parent  = &s3c24xx_dclk1;
+
+	s3c24xx_uclk.parent  = &s3c24xx_clkout1;
+
+	s3c24xx_register_clocks(anubis_clocks, ARRAY_SIZE(anubis_clocks));
+
+	s3c_device_nand.dev.platform_data = &anubis_nand_info;
+
+	s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc));
+	s3c24xx_init_clocks(0);
+	s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs));
+
+	/* check for the newer revision boards with large page nand */
+
+	if ((__raw_readb(ANUBIS_VA_IDREG) & ANUBIS_IDREG_REVMASK) >= 4) {
+		printk(KERN_INFO "ANUBIS-B detected (revision %d)\n",
+		       __raw_readb(ANUBIS_VA_IDREG) & ANUBIS_IDREG_REVMASK);
+		anubis_nand_sets[0].partitions = anubis_default_nand_part_large;
+		anubis_nand_sets[0].nr_partitions = ARRAY_SIZE(anubis_default_nand_part_large);
+	} else {
+		/* ensure that the GPIO is setup */
+		s3c2410_gpio_setpin(S3C2410_GPA(0), 1);
+	}
+}
+
+static void __init anubis_init(void)
+{
+	s3c_i2c0_set_platdata(NULL);
+	platform_add_devices(anubis_devices, ARRAY_SIZE(anubis_devices));
+
+	i2c_register_board_info(0, anubis_i2c_devs,
+				ARRAY_SIZE(anubis_i2c_devs));
+}
+
+
+MACHINE_START(ANUBIS, "Simtec-Anubis")
+	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= anubis_map_io,
+	.init_machine	= anubis_init,
+	.init_irq	= s3c24xx_init_irq,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/mach-at2440evb.c

@@ -0,0 +1,245 @@
+/* linux/arch/arm/mach-s3c2440/mach-at2440evb.c
+ *
+ * Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com>
+ *      Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk>
+ *      and modifications by SBZ <sbz@spgui.org> and
+ *      Weibing <http://weibing.blogbus.com>
+ *
+ * For product information, visit http://www.arm9e.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/serial_core.h>
+#include <linux/dm9000.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <plat/nand.h>
+#include <plat/iic.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/mci.h>
+
+static struct map_desc at2440evb_iodesc[] __initdata = {
+	/* Nothing here */
+};
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
+#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
+
+static struct s3c24xx_uart_clksrc at2440evb_serial_clocks[] = {
+	[0] = {
+		.name		= "uclk",
+		.divisor	= 1,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	},
+	[1] = {
+		.name		= "pclk",
+		.divisor	= 1,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	}
+};
+
+
+static struct s3c2410_uartcfg at2440evb_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = at2440evb_serial_clocks,
+		.clocks_size = ARRAY_SIZE(at2440evb_serial_clocks),
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = at2440evb_serial_clocks,
+		.clocks_size = ARRAY_SIZE(at2440evb_serial_clocks),
+	},
+};
+
+/* NAND Flash on AT2440EVB board */
+
+static struct mtd_partition at2440evb_default_nand_part[] = {
+	[0] = {
+		.name	= "Boot Agent",
+		.size	= SZ_256K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "Kernel",
+		.size	= SZ_2M,
+		.offset	= SZ_256K,
+	},
+	[2] = {
+		.name	= "Root",
+		.offset	= SZ_256K + SZ_2M,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct s3c2410_nand_set at2440evb_nand_sets[] = {
+	[0] = {
+		.name		= "nand",
+		.nr_chips	= 1,
+		.nr_partitions	= ARRAY_SIZE(at2440evb_default_nand_part),
+		.partitions	= at2440evb_default_nand_part,
+	},
+};
+
+static struct s3c2410_platform_nand at2440evb_nand_info = {
+	.tacls		= 25,
+	.twrph0		= 55,
+	.twrph1		= 40,
+	.nr_sets	= ARRAY_SIZE(at2440evb_nand_sets),
+	.sets		= at2440evb_nand_sets,
+};
+
+/* DM9000AEP 10/100 ethernet controller */
+
+static struct resource at2440evb_dm9k_resource[] = {
+	[0] = {
+		.start = S3C2410_CS3,
+		.end   = S3C2410_CS3 + 3,
+		.flags = IORESOURCE_MEM
+	},
+	[1] = {
+		.start = S3C2410_CS3 + 4,
+		.end   = S3C2410_CS3 + 7,
+		.flags = IORESOURCE_MEM
+	},
+	[2] = {
+		.start = IRQ_EINT7,
+		.end   = IRQ_EINT7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	}
+};
+
+static struct dm9000_plat_data at2440evb_dm9k_pdata = {
+	.flags		= (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
+};
+
+static struct platform_device at2440evb_device_eth = {
+	.name		= "dm9000",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(at2440evb_dm9k_resource),
+	.resource	= at2440evb_dm9k_resource,
+	.dev		= {
+		.platform_data	= &at2440evb_dm9k_pdata,
+	},
+};
+
+static struct s3c24xx_mci_pdata at2440evb_mci_pdata = {
+	.gpio_detect	= S3C2410_GPG(10),
+};
+
+/* 7" LCD panel */
+
+static struct s3c2410fb_display at2440evb_lcd_cfg __initdata = {
+
+	.lcdcon5	= S3C2410_LCDCON5_FRM565 |
+			  S3C2410_LCDCON5_INVVLINE |
+			  S3C2410_LCDCON5_INVVFRAME |
+			  S3C2410_LCDCON5_PWREN |
+			  S3C2410_LCDCON5_HWSWP,
+
+	.type		= S3C2410_LCDCON1_TFT,
+
+	.width		= 800,
+	.height		= 480,
+
+	.pixclock	= 33333, /* HCLK 60 MHz, divisor 2 */
+	.xres		= 800,
+	.yres		= 480,
+	.bpp		= 16,
+	.left_margin	= 88,
+	.right_margin	= 40,
+	.hsync_len	= 128,
+	.upper_margin	= 32,
+	.lower_margin	= 11,
+	.vsync_len	= 2,
+};
+
+static struct s3c2410fb_mach_info at2440evb_fb_info __initdata = {
+	.displays	= &at2440evb_lcd_cfg,
+	.num_displays	= 1,
+	.default_display = 0,
+};
+
+static struct platform_device *at2440evb_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_wdt,
+	&s3c_device_adc,
+	&s3c_device_i2c0,
+	&s3c_device_rtc,
+	&s3c_device_nand,
+	&s3c_device_sdi,
+	&s3c_device_lcd,
+	&at2440evb_device_eth,
+};
+
+static void __init at2440evb_map_io(void)
+{
+	s3c_device_nand.dev.platform_data = &at2440evb_nand_info;
+	s3c_device_sdi.name = "s3c2440-sdi";
+	s3c_device_sdi.dev.platform_data = &at2440evb_mci_pdata;
+
+	s3c24xx_init_io(at2440evb_iodesc, ARRAY_SIZE(at2440evb_iodesc));
+	s3c24xx_init_clocks(16934400);
+	s3c24xx_init_uarts(at2440evb_uartcfgs, ARRAY_SIZE(at2440evb_uartcfgs));
+}
+
+static void __init at2440evb_init(void)
+{
+	s3c24xx_fb_set_platdata(&at2440evb_fb_info);
+	s3c_i2c0_set_platdata(NULL);
+
+	platform_add_devices(at2440evb_devices, ARRAY_SIZE(at2440evb_devices));
+}
+
+
+MACHINE_START(AT2440EVB, "AT2440EVB")
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= at2440evb_map_io,
+	.init_machine	= at2440evb_init,
+	.init_irq	= s3c24xx_init_irq,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/mach-mini2440.c

@@ -0,0 +1,702 @@
+/* linux/arch/arm/mach-s3c2440/mach-mini2440.c
+ *
+ * Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com>
+ *      Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk>
+ *      and modifications by SBZ <sbz@spgui.org> and
+ *      Weibing <http://weibing.blogbus.com> and
+ *      Michel Pollet <buserror@gmail.com>
+ *
+ * For product information, visit http://code.google.com/p/mini2440/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/io.h>
+#include <linux/serial_core.h>
+#include <linux/dm9000.h>
+#include <linux/i2c/at24.h>
+#include <linux/platform_device.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c.h>
+#include <linux/mmc/host.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/irqs.h>
+#include <plat/nand.h>
+#include <plat/iic.h>
+#include <plat/mci.h>
+#include <plat/udc.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#include <sound/s3c24xx_uda134x.h>
+
+#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
+
+static struct map_desc mini2440_iodesc[] __initdata = {
+	/* nothing to declare, move along */
+};
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+
+static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+};
+
+/* USB device UDC support */
+
+static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
+{
+	pr_debug("udc: pullup(%d)\n", cmd);
+
+	switch (cmd) {
+		case S3C2410_UDC_P_ENABLE :
+			s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+			break;
+		case S3C2410_UDC_P_DISABLE :
+			s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+			break;
+		case S3C2410_UDC_P_RESET :
+			break;
+		default:
+			break;
+	}
+}
+
+static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = {
+	.udc_command		= mini2440_udc_pullup,
+};
+
+
+/* LCD timing and setup */
+
+/*
+ * This macro simplifies the table bellow
+ */
+#define _LCD_DECLARE(_clock,_xres,margin_left,margin_right,hsync, \
+			_yres,margin_top,margin_bottom,vsync, refresh) \
+	.width = _xres, \
+	.xres = _xres, \
+	.height = _yres, \
+	.yres = _yres, \
+	.left_margin	= margin_left,	\
+	.right_margin	= margin_right,	\
+	.upper_margin	= margin_top,	\
+	.lower_margin	= margin_bottom,	\
+	.hsync_len	= hsync,	\
+	.vsync_len	= vsync,	\
+	.pixclock	= ((_clock*100000000000LL) /	\
+			   ((refresh) * \
+			   (hsync + margin_left + _xres + margin_right) * \
+			   (vsync + margin_top + _yres + margin_bottom))), \
+	.bpp		= 16,\
+	.type		= (S3C2410_LCDCON1_TFT16BPP |\
+			   S3C2410_LCDCON1_TFT)
+
+static struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
+	[0] = {	/* mini2440 + 3.5" TFT + touchscreen */
+		_LCD_DECLARE(
+			7,			/* The 3.5 is quite fast */
+			240, 21, 38, 6, 	/* x timing */
+			320, 4, 4, 2,		/* y timing */
+			60),			/* refresh rate */
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_INVVLINE |
+				   S3C2410_LCDCON5_INVVFRAME |
+				   S3C2410_LCDCON5_INVVDEN |
+				   S3C2410_LCDCON5_PWREN),
+	},
+	[1] = { /* mini2440 + 7" TFT + touchscreen */
+		_LCD_DECLARE(
+			10,			/* the 7" runs slower */
+			800, 40, 40, 48, 	/* x timing */
+			480, 29, 3, 3,		/* y timing */
+			50),			/* refresh rate */
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_INVVLINE |
+				   S3C2410_LCDCON5_INVVFRAME |
+				   S3C2410_LCDCON5_PWREN),
+	},
+	/* The VGA shield can outout at several resolutions. All share 
+	 * the same timings, however, anything smaller than 1024x768
+	 * will only be displayed in the top left corner of a 1024x768
+	 * XGA output unless you add optional dip switches to the shield.
+	 * Therefore timings for other resolutions have been ommited here.
+	 */
+	[2] = {
+		_LCD_DECLARE(
+			10,
+			1024, 1, 2, 2,		/* y timing */
+			768, 200, 16, 16, 	/* x timing */
+			24),	/* refresh rate, maximum stable,
+				 tested with the FPGA shield */
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_HWSWP),
+	},
+};
+
+/* todo - put into gpio header */
+
+#define S3C2410_GPCCON_MASK(x)	(3 << ((x) * 2))
+#define S3C2410_GPDCON_MASK(x)	(3 << ((x) * 2))
+
+static struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
+	.displays	 = &mini2440_lcd_cfg[0], /* not constant! see init */
+	.num_displays	 = 1,
+	.default_display = 0,
+
+	/* Enable VD[2..7], VD[10..15], VD[18..23] and VCLK, syncs, VDEN
+	 * and disable the pull down resistors on pins we are using for LCD
+	 * data. */
+
+	.gpcup		= (0xf << 1) | (0x3f << 10),
+
+	.gpccon		= (S3C2410_GPC1_VCLK   | S3C2410_GPC2_VLINE |
+			   S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM |
+			   S3C2410_GPC10_VD2   | S3C2410_GPC11_VD3 |
+			   S3C2410_GPC12_VD4   | S3C2410_GPC13_VD5 |
+			   S3C2410_GPC14_VD6   | S3C2410_GPC15_VD7),
+
+	.gpccon_mask	= (S3C2410_GPCCON_MASK(1)  | S3C2410_GPCCON_MASK(2)  |
+			   S3C2410_GPCCON_MASK(3)  | S3C2410_GPCCON_MASK(4)  |
+			   S3C2410_GPCCON_MASK(10) | S3C2410_GPCCON_MASK(11) |
+			   S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
+			   S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
+
+	.gpdup		= (0x3f << 2) | (0x3f << 10),
+
+	.gpdcon		= (S3C2410_GPD2_VD10  | S3C2410_GPD3_VD11 |
+			   S3C2410_GPD4_VD12  | S3C2410_GPD5_VD13 |
+			   S3C2410_GPD6_VD14  | S3C2410_GPD7_VD15 |
+			   S3C2410_GPD10_VD18 | S3C2410_GPD11_VD19 |
+			   S3C2410_GPD12_VD20 | S3C2410_GPD13_VD21 |
+			   S3C2410_GPD14_VD22 | S3C2410_GPD15_VD23),
+
+	.gpdcon_mask	= (S3C2410_GPDCON_MASK(2)  | S3C2410_GPDCON_MASK(3) |
+			   S3C2410_GPDCON_MASK(4)  | S3C2410_GPDCON_MASK(5) |
+			   S3C2410_GPDCON_MASK(6)  | S3C2410_GPDCON_MASK(7) |
+			   S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
+			   S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
+			   S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+};
+
+/* MMC/SD  */
+
+static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = {
+   .gpio_detect   = S3C2410_GPG(8),
+   .gpio_wprotect = S3C2410_GPH(8),
+   .set_power     = NULL,
+   .ocr_avail     = MMC_VDD_32_33|MMC_VDD_33_34,
+};
+
+/* NAND Flash on MINI2440 board */
+
+static struct mtd_partition mini2440_default_nand_part[] __initdata = {
+	[0] = {
+		.name	= "u-boot",
+		.size	= SZ_256K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "u-boot-env",
+		.size	= SZ_128K,
+		.offset	= SZ_256K,
+	},
+	[2] = {
+		.name	= "kernel",
+		/* 5 megabytes, for a kernel with no modules
+		 * or a uImage with a ramdisk attached */
+		.size	= 0x00500000,
+		.offset	= SZ_256K + SZ_128K,
+	},
+	[3] = {
+		.name	= "root",
+		.offset	= SZ_256K + SZ_128K + 0x00500000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct s3c2410_nand_set mini2440_nand_sets[] __initdata = {
+	[0] = {
+		.name		= "nand",
+		.nr_chips	= 1,
+		.nr_partitions	= ARRAY_SIZE(mini2440_default_nand_part),
+		.partitions	= mini2440_default_nand_part,
+		.flash_bbt 	= 1, /* we use u-boot to create a BBT */
+	},
+};
+
+static struct s3c2410_platform_nand mini2440_nand_info __initdata = {
+	.tacls		= 0,
+	.twrph0		= 25,
+	.twrph1		= 15,
+	.nr_sets	= ARRAY_SIZE(mini2440_nand_sets),
+	.sets		= mini2440_nand_sets,
+	.ignore_unset_ecc = 1,
+};
+
+/* DM9000AEP 10/100 ethernet controller */
+
+static struct resource mini2440_dm9k_resource[] __initdata = {
+	[0] = {
+		.start = MACH_MINI2440_DM9K_BASE,
+		.end   = MACH_MINI2440_DM9K_BASE + 3,
+		.flags = IORESOURCE_MEM
+	},
+	[1] = {
+		.start = MACH_MINI2440_DM9K_BASE + 4,
+		.end   = MACH_MINI2440_DM9K_BASE + 7,
+		.flags = IORESOURCE_MEM
+	},
+	[2] = {
+		.start = IRQ_EINT7,
+		.end   = IRQ_EINT7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	}
+};
+
+/*
+ * The DM9000 has no eeprom, and it's MAC address is set by
+ * the bootloader before starting the kernel.
+ */
+static struct dm9000_plat_data mini2440_dm9k_pdata __initdata = {
+	.flags		= (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
+};
+
+static struct platform_device mini2440_device_eth __initdata = {
+	.name		= "dm9000",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(mini2440_dm9k_resource),
+	.resource	= mini2440_dm9k_resource,
+	.dev		= {
+		.platform_data	= &mini2440_dm9k_pdata,
+	},
+};
+
+/*  CON5
+ *	+--+	 /-----\
+ *	|  |    |	|
+ *	|  |	|  BAT	|
+ *	|  |	 \_____/
+ *	|  |
+ *	|  |  +----+  +----+
+ *	|  |  | K5 |  | K1 |
+ *	|  |  +----+  +----+
+ *	|  |  +----+  +----+
+ *	|  |  | K4 |  | K2 |
+ *	|  |  +----+  +----+
+ *	|  |  +----+  +----+
+ *	|  |  | K6 |  | K3 |
+ *	|  |  +----+  +----+
+ *	  .....
+ */
+static struct gpio_keys_button mini2440_buttons[] __initdata = {
+	{
+		.gpio		= S3C2410_GPG(0),		/* K1 */
+		.code		= KEY_F1,
+		.desc		= "Button 1",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(3),		/* K2 */
+		.code		= KEY_F2,
+		.desc		= "Button 2",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(5),		/* K3 */
+		.code		= KEY_F3,
+		.desc		= "Button 3",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(6),		/* K4 */
+		.code		= KEY_POWER,
+		.desc		= "Power",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(7),		/* K5 */
+		.code		= KEY_F5,
+		.desc		= "Button 5",
+		.active_low	= 1,
+	},
+#if 0
+	/* this pin is also known as TCLK1 and seems to already
+	 * marked as "in use" somehow in the kernel -- possibly wrongly */
+	{
+		.gpio		= S3C2410_GPG(11),	/* K6 */
+		.code		= KEY_F6,
+		.desc		= "Button 6",
+		.active_low	= 1,
+	},
+#endif
+};
+
+static struct gpio_keys_platform_data mini2440_button_data __initdata = {
+	.buttons	= mini2440_buttons,
+	.nbuttons	= ARRAY_SIZE(mini2440_buttons),
+};
+
+static struct platform_device mini2440_button_device __initdata = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &mini2440_button_data,
+	}
+};
+
+/* LEDS */
+
+static struct s3c24xx_led_platdata mini2440_led1_pdata __initdata = {
+	.name		= "led1",
+	.gpio		= S3C2410_GPB(5),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "heartbeat",
+};
+
+static struct s3c24xx_led_platdata mini2440_led2_pdata __initdata = {
+	.name		= "led2",
+	.gpio		= S3C2410_GPB(6),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "nand-disk",
+};
+
+static struct s3c24xx_led_platdata mini2440_led3_pdata __initdata = {
+	.name		= "led3",
+	.gpio		= S3C2410_GPB(7),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "mmc0",
+};
+
+static struct s3c24xx_led_platdata mini2440_led4_pdata __initdata = {
+	.name		= "led4",
+	.gpio		= S3C2410_GPB(8),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "",
+};
+
+static struct s3c24xx_led_platdata mini2440_led_backlight_pdata __initdata = {
+	.name		= "backlight",
+	.gpio		= S3C2410_GPG(4),
+	.def_trigger	= "backlight",
+};
+
+static struct platform_device mini2440_led1 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 1,
+	.dev		= {
+		.platform_data	= &mini2440_led1_pdata,
+	},
+};
+
+static struct platform_device mini2440_led2 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 2,
+	.dev		= {
+		.platform_data	= &mini2440_led2_pdata,
+	},
+};
+
+static struct platform_device mini2440_led3 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 3,
+	.dev		= {
+		.platform_data	= &mini2440_led3_pdata,
+	},
+};
+
+static struct platform_device mini2440_led4 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 4,
+	.dev		= {
+		.platform_data	= &mini2440_led4_pdata,
+	},
+};
+
+static struct platform_device mini2440_led_backlight __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 5,
+	.dev		= {
+		.platform_data	= &mini2440_led_backlight_pdata,
+	},
+};
+
+/* AUDIO */
+
+static struct s3c24xx_uda134x_platform_data mini2440_audio_pins __initdata = {
+	.l3_clk = S3C2410_GPB(4),
+	.l3_mode = S3C2410_GPB(2),
+	.l3_data = S3C2410_GPB(3),
+	.model = UDA134X_UDA1341
+};
+
+static struct platform_device mini2440_audio __initdata = {
+	.name		= "s3c24xx_uda134x",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &mini2440_audio_pins,
+	},
+};
+
+/*
+ * I2C devices
+ */
+static struct at24_platform_data at24c08 = {
+	.byte_len	= SZ_8K / 8,
+	.page_size	= 16,
+};
+
+static struct i2c_board_info mini2440_i2c_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("24c08", 0x50),
+		.platform_data = &at24c08,
+	},
+};
+
+static struct platform_device *mini2440_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_wdt,
+/*	&s3c_device_adc,*/ /* ADC doesn't like living with touchscreen ! */
+	&s3c_device_i2c0,
+	&s3c_device_rtc,
+	&s3c_device_usbgadget,
+	&mini2440_device_eth,
+	&mini2440_led1,
+	&mini2440_led2,
+	&mini2440_led3,
+	&mini2440_led4,
+	&mini2440_button_device,
+	&s3c_device_nand,
+	&s3c_device_sdi,
+	&s3c_device_iis,
+	&mini2440_audio,
+/*	&s3c_device_timer[0],*/	/* buzzer pwm, no API for it */
+	/* remaining devices are optional */
+};
+
+static void __init mini2440_map_io(void)
+{
+	s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs));
+
+	s3c_device_nand.dev.platform_data = &mini2440_nand_info;
+	s3c_device_sdi.dev.platform_data = &mini2440_mmc_cfg;
+}
+
+/*
+ * mini2440_features string
+ *
+ * t = Touchscreen present
+ * b = backlight control
+ * c = camera [TODO]
+ * 0-9 LCD configuration
+ *
+ */
+static char mini2440_features_str[12] __initdata = "0tb";
+
+static int __init mini2440_features_setup(char *str)
+{
+	if (str)
+		strlcpy(mini2440_features_str, str, sizeof(mini2440_features_str));
+	return 1;
+}
+
+__setup("mini2440=", mini2440_features_setup);
+
+#define FEATURE_SCREEN (1 << 0)
+#define FEATURE_BACKLIGHT (1 << 1)
+#define FEATURE_TOUCH (1 << 2)
+#define FEATURE_CAMERA (1 << 3)
+
+struct mini2440_features_t {
+	int count;
+	int done;
+	int lcd_index;
+	struct platform_device *optional[8];
+};
+
+static void mini2440_parse_features(
+		struct mini2440_features_t * features,
+		const char * features_str )
+{
+	const char * fp = features_str;
+
+	features->count = 0;
+	features->done = 0;
+	features->lcd_index = -1;
+
+	while (*fp) {
+		char f = *fp++;
+
+		switch (f) {
+		case '0'...'9':	/* tft screen */
+			if (features->done & FEATURE_SCREEN) {
+				printk(KERN_INFO "MINI2440: '%c' ignored, "
+					"screen type already set\n", f);
+			} else {
+				int li = f - '0';
+				if (li >= ARRAY_SIZE(mini2440_lcd_cfg))
+					printk(KERN_INFO "MINI2440: "
+						"'%c' out of range LCD mode\n", f);
+				else {
+					features->optional[features->count++] =
+							&s3c_device_lcd;
+					features->lcd_index = li;
+				}
+			}
+			features->done |= FEATURE_SCREEN;
+			break;
+		case 'b':
+			if (features->done & FEATURE_BACKLIGHT)
+				printk(KERN_INFO "MINI2440: '%c' ignored, "
+					"backlight already set\n", f);
+			else {
+				features->optional[features->count++] =
+						&mini2440_led_backlight;
+			}
+			features->done |= FEATURE_BACKLIGHT;
+			break;
+		case 't':
+			printk(KERN_INFO "MINI2440: '%c' ignored, "
+				"touchscreen not compiled in\n", f);
+			break;
+		case 'c':
+			if (features->done & FEATURE_CAMERA)
+				printk(KERN_INFO "MINI2440: '%c' ignored, "
+					"camera already registered\n", f);
+			else
+				features->optional[features->count++] =
+					&s3c_device_camif;
+			features->done |= FEATURE_CAMERA;
+			break;
+		}
+	}
+}
+
+static void __init mini2440_init(void)
+{
+	struct mini2440_features_t features = { 0 };
+	int i;
+
+	printk(KERN_INFO "MINI2440: Option string mini2440=%s\n",
+			mini2440_features_str);
+
+	/* Parse the feature string */
+	mini2440_parse_features(&features, mini2440_features_str);
+
+	/* turn LCD on */
+	s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
+
+	/* Turn the backlight early on */
+	s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
+
+	/* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
+	s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
+	s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
+
+	/* Make sure the D+ pullup pin is output */
+	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+
+	/* mark the key as input, without pullups (there is one on the board) */
+	for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
+		s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
+		s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio,
+					S3C2410_GPIO_INPUT);
+	}
+	if (features.lcd_index != -1) {
+		int li;
+
+		mini2440_fb_info.displays =
+			&mini2440_lcd_cfg[features.lcd_index];
+
+		printk(KERN_INFO "MINI2440: LCD");
+		for (li = 0; li < ARRAY_SIZE(mini2440_lcd_cfg); li++)
+			if (li == features.lcd_index)
+				printk(" [%d:%dx%d]", li,
+					mini2440_lcd_cfg[li].width,
+					mini2440_lcd_cfg[li].height);
+			else
+				printk(" %d:%dx%d", li,
+					mini2440_lcd_cfg[li].width,
+					mini2440_lcd_cfg[li].height);
+		printk("\n");
+		s3c24xx_fb_set_platdata(&mini2440_fb_info);
+	}
+	s3c24xx_udc_set_platdata(&mini2440_udc_cfg);
+	s3c_i2c0_set_platdata(NULL);
+	i2c_register_board_info(0, mini2440_i2c_devs,
+				ARRAY_SIZE(mini2440_i2c_devs));
+
+	platform_add_devices(mini2440_devices, ARRAY_SIZE(mini2440_devices));
+
+	if (features.count)	/* the optional features */
+		platform_add_devices(features.optional, features.count);
+
+}
+
+
+MACHINE_START(MINI2440, "MINI2440")
+	/* Maintainer: Michel Pollet <buserror@gmail.com> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= mini2440_map_io,
+	.init_machine	= mini2440_init,
+	.init_irq	= s3c24xx_init_irq,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/mach-nexcoder.c

@@ -0,0 +1,160 @@
+/* linux/arch/arm/mach-s3c2440/mach-nexcoder.c
+ *
+ * Copyright (c) 2004 Nex Vision
+ *   Guillaume GOURAT <guillaume.gourat@nexvision.tv>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Modifications:
+ *     15-10-2004 GG  Created initial version
+ *     12-03-2005 BJD Updated for release
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/string.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <linux/mtd/map.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/setup.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+//#include <asm/debug-ll.h>
+#include <mach/regs-gpio.h>
+#include <plat/regs-serial.h>
+#include <plat/iic.h>
+
+#include <plat/s3c2410.h>
+#include <plat/s3c2440.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+static struct map_desc nexcoder_iodesc[] __initdata = {
+	/* nothing here yet */
+};
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG12 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg nexcoder_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	}
+};
+
+/* NOR Flash on NexVision NexCoder 2440 board */
+
+static struct resource nexcoder_nor_resource[] = {
+	[0] = {
+		.start = S3C2410_CS0,
+		.end   = S3C2410_CS0 + (8*1024*1024) - 1,
+		.flags = IORESOURCE_MEM,
+	}
+};
+
+static struct map_info nexcoder_nor_map = {
+	.bankwidth = 2,
+};
+
+static struct platform_device nexcoder_device_nor = {
+	.name		= "mtd-flash",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(nexcoder_nor_resource),
+	.resource	= nexcoder_nor_resource,
+	.dev =
+	{
+		.platform_data = &nexcoder_nor_map,
+	}
+};
+
+/* Standard Nexcoder devices */
+
+static struct platform_device *nexcoder_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_lcd,
+	&s3c_device_wdt,
+	&s3c_device_i2c0,
+	&s3c_device_iis,
+ 	&s3c_device_rtc,
+	&s3c_device_camif,
+	&s3c_device_spi0,
+	&s3c_device_spi1,
+	&nexcoder_device_nor,
+};
+
+static void __init nexcoder_sensorboard_init(void)
+{
+	// Initialize SCCB bus
+	s3c2410_gpio_setpin(S3C2410_GPE(14), 1); // IICSCL
+	s3c2410_gpio_cfgpin(S3C2410_GPE(14), S3C2410_GPIO_OUTPUT);
+	s3c2410_gpio_setpin(S3C2410_GPE(15), 1); // IICSDA
+	s3c2410_gpio_cfgpin(S3C2410_GPE(15), S3C2410_GPIO_OUTPUT);
+
+	// Power up the sensor board
+	s3c2410_gpio_setpin(S3C2410_GPF(1), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(1), S3C2410_GPIO_OUTPUT); // CAM_GPIO7 => nLDO_PWRDN
+	s3c2410_gpio_setpin(S3C2410_GPF(2), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPF(2), S3C2410_GPIO_OUTPUT); // CAM_GPIO6 => CAM_PWRDN
+}
+
+static void __init nexcoder_map_io(void)
+{
+	s3c24xx_init_io(nexcoder_iodesc, ARRAY_SIZE(nexcoder_iodesc));
+	s3c24xx_init_clocks(0);
+	s3c24xx_init_uarts(nexcoder_uartcfgs, ARRAY_SIZE(nexcoder_uartcfgs));
+
+	nexcoder_sensorboard_init();
+}
+
+static void __init nexcoder_init(void)
+{
+	s3c_i2c0_set_platdata(NULL);
+	platform_add_devices(nexcoder_devices, ARRAY_SIZE(nexcoder_devices));
+};
+
+MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440")
+	/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= nexcoder_map_io,
+	.init_machine	= nexcoder_init,
+	.init_irq	= s3c24xx_init_irq,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/mach-osiris.c

@@ -0,0 +1,429 @@
+/* linux/arch/arm/mach-s3c2440/mach-osiris.c
+ *
+ * Copyright (c) 2005,2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/device.h>
+#include <linux/sysdev.h>
+#include <linux/serial_core.h>
+#include <linux/clk.h>
+#include <linux/i2c.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/osiris-map.h>
+#include <mach/osiris-cpld.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/cpu-freq.h>
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <plat/nand.h>
+#include <plat/iic.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+/* onboard perihperal map */
+
+static struct map_desc osiris_iodesc[] __initdata = {
+  /* ISA IO areas (may be over-written later) */
+
+  {
+	  .virtual	= (u32)S3C24XX_VA_ISA_BYTE,
+	  .pfn		= __phys_to_pfn(S3C2410_CS5),
+	  .length	= SZ_16M,
+	  .type		= MT_DEVICE,
+  }, {
+	  .virtual	= (u32)S3C24XX_VA_ISA_WORD,
+	  .pfn		= __phys_to_pfn(S3C2410_CS5),
+	  .length	= SZ_16M,
+	  .type		= MT_DEVICE,
+  },
+
+  /* CPLD control registers */
+
+  {
+	  .virtual	= (u32)OSIRIS_VA_CTRL0,
+	  .pfn		= __phys_to_pfn(OSIRIS_PA_CTRL0),
+	  .length	= SZ_16K,
+	  .type		= MT_DEVICE,
+  }, {
+	  .virtual	= (u32)OSIRIS_VA_CTRL1,
+	  .pfn		= __phys_to_pfn(OSIRIS_PA_CTRL1),
+	  .length	= SZ_16K,
+	  .type		= MT_DEVICE,
+  }, {
+	  .virtual	= (u32)OSIRIS_VA_CTRL2,
+	  .pfn		= __phys_to_pfn(OSIRIS_PA_CTRL2),
+	  .length	= SZ_16K,
+	  .type		= MT_DEVICE,
+  }, {
+	  .virtual	= (u32)OSIRIS_VA_IDREG,
+	  .pfn		= __phys_to_pfn(OSIRIS_PA_IDREG),
+	  .length	= SZ_16K,
+	  .type		= MT_DEVICE,
+  },
+};
+
+#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c24xx_uart_clksrc osiris_serial_clocks[] = {
+	[0] = {
+		.name		= "uclk",
+		.divisor	= 1,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	},
+	[1] = {
+		.name		= "pclk",
+		.divisor	= 1,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	}
+};
+
+static struct s3c2410_uartcfg osiris_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = osiris_serial_clocks,
+		.clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = osiris_serial_clocks,
+		.clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+		.clocks	     = osiris_serial_clocks,
+		.clocks_size = ARRAY_SIZE(osiris_serial_clocks),
+	}
+};
+
+/* NAND Flash on Osiris board */
+
+static int external_map[]   = { 2 };
+static int chip0_map[]      = { 0 };
+static int chip1_map[]      = { 1 };
+
+static struct mtd_partition osiris_default_nand_part[] = {
+	[0] = {
+		.name	= "Boot Agent",
+		.size	= SZ_16K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "/boot",
+		.size	= SZ_4M - SZ_16K,
+		.offset	= SZ_16K,
+	},
+	[2] = {
+		.name	= "user1",
+		.offset	= SZ_4M,
+		.size	= SZ_32M - SZ_4M,
+	},
+	[3] = {
+		.name	= "user2",
+		.offset	= SZ_32M,
+		.size	= MTDPART_SIZ_FULL,
+	}
+};
+
+static struct mtd_partition osiris_default_nand_part_large[] = {
+	[0] = {
+		.name	= "Boot Agent",
+		.size	= SZ_128K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "/boot",
+		.size	= SZ_4M - SZ_128K,
+		.offset	= SZ_128K,
+	},
+	[2] = {
+		.name	= "user1",
+		.offset	= SZ_4M,
+		.size	= SZ_32M - SZ_4M,
+	},
+	[3] = {
+		.name	= "user2",
+		.offset	= SZ_32M,
+		.size	= MTDPART_SIZ_FULL,
+	}
+};
+
+/* the Osiris has 3 selectable slots for nand-flash, the two
+ * on-board chip areas, as well as the external slot.
+ *
+ * Note, there is no current hot-plug support for the External
+ * socket.
+*/
+
+static struct s3c2410_nand_set osiris_nand_sets[] = {
+	[1] = {
+		.name		= "External",
+		.nr_chips	= 1,
+		.nr_map		= external_map,
+		.nr_partitions	= ARRAY_SIZE(osiris_default_nand_part),
+		.partitions	= osiris_default_nand_part,
+	},
+	[0] = {
+		.name		= "chip0",
+		.nr_chips	= 1,
+		.nr_map		= chip0_map,
+		.nr_partitions	= ARRAY_SIZE(osiris_default_nand_part),
+		.partitions	= osiris_default_nand_part,
+	},
+	[2] = {
+		.name		= "chip1",
+		.nr_chips	= 1,
+		.nr_map		= chip1_map,
+		.nr_partitions	= ARRAY_SIZE(osiris_default_nand_part),
+		.partitions	= osiris_default_nand_part,
+	},
+};
+
+static void osiris_nand_select(struct s3c2410_nand_set *set, int slot)
+{
+	unsigned int tmp;
+
+	slot = set->nr_map[slot] & 3;
+
+	pr_debug("osiris_nand: selecting slot %d (set %p,%p)\n",
+		 slot, set, set->nr_map);
+
+	tmp = __raw_readb(OSIRIS_VA_CTRL0);
+	tmp &= ~OSIRIS_CTRL0_NANDSEL;
+	tmp |= slot;
+
+	pr_debug("osiris_nand: ctrl0 now %02x\n", tmp);
+
+	__raw_writeb(tmp, OSIRIS_VA_CTRL0);
+}
+
+static struct s3c2410_platform_nand osiris_nand_info = {
+	.tacls		= 25,
+	.twrph0		= 60,
+	.twrph1		= 60,
+	.nr_sets	= ARRAY_SIZE(osiris_nand_sets),
+	.sets		= osiris_nand_sets,
+	.select_chip	= osiris_nand_select,
+};
+
+/* PCMCIA control and configuration */
+
+static struct resource osiris_pcmcia_resource[] = {
+	[0] = {
+		.start	= 0x0f000000,
+		.end	= 0x0f100000,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= 0x0c000000,
+		.end	= 0x0c100000,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device osiris_pcmcia = {
+	.name		= "osiris-pcmcia",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(osiris_pcmcia_resource),
+	.resource	= osiris_pcmcia_resource,
+};
+
+/* Osiris power management device */
+
+#ifdef CONFIG_PM
+static unsigned char pm_osiris_ctrl0;
+
+static int osiris_pm_suspend(struct sys_device *sd, pm_message_t state)
+{
+	unsigned int tmp;
+
+	pm_osiris_ctrl0 = __raw_readb(OSIRIS_VA_CTRL0);
+	tmp = pm_osiris_ctrl0 & ~OSIRIS_CTRL0_NANDSEL;
+
+	/* ensure correct NAND slot is selected on resume */
+	if ((pm_osiris_ctrl0 & OSIRIS_CTRL0_BOOT_INT) == 0)
+	        tmp |= 2;
+
+	__raw_writeb(tmp, OSIRIS_VA_CTRL0);
+
+	/* ensure that an nRESET is not generated on resume. */
+	s3c2410_gpio_setpin(S3C2410_GPA(21), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPIO_OUTPUT);
+
+	return 0;
+}
+
+static int osiris_pm_resume(struct sys_device *sd)
+{
+	if (pm_osiris_ctrl0 & OSIRIS_CTRL0_FIX8)
+		__raw_writeb(OSIRIS_CTRL1_FIX8, OSIRIS_VA_CTRL1);
+
+	__raw_writeb(pm_osiris_ctrl0, OSIRIS_VA_CTRL0);
+
+	s3c2410_gpio_cfgpin(S3C2410_GPA(21), S3C2410_GPA21_nRSTOUT);
+
+	return 0;
+}
+
+#else
+#define osiris_pm_suspend NULL
+#define osiris_pm_resume NULL
+#endif
+
+static struct sysdev_class osiris_pm_sysclass = {
+	.name		= "mach-osiris",
+	.suspend	= osiris_pm_suspend,
+	.resume		= osiris_pm_resume,
+};
+
+static struct sys_device osiris_pm_sysdev = {
+	.cls		= &osiris_pm_sysclass,
+};
+
+/* I2C devices fitted. */
+
+static struct i2c_board_info osiris_i2c_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("tps65011", 0x48),
+		.irq	= IRQ_EINT20,
+	},
+};
+
+/* Standard Osiris devices */
+
+static struct platform_device *osiris_devices[] __initdata = {
+	&s3c_device_i2c0,
+	&s3c_device_wdt,
+	&s3c_device_nand,
+	&osiris_pcmcia,
+};
+
+static struct clk *osiris_clocks[] __initdata = {
+	&s3c24xx_dclk0,
+	&s3c24xx_dclk1,
+	&s3c24xx_clkout0,
+	&s3c24xx_clkout1,
+	&s3c24xx_uclk,
+};
+
+static struct s3c_cpufreq_board __initdata osiris_cpufreq = {
+	.refresh	= 7800, /* refresh period is 7.8usec */
+	.auto_io	= 1,
+	.need_io	= 1,
+};
+
+static void __init osiris_map_io(void)
+{
+	unsigned long flags;
+
+	/* initialise the clocks */
+
+	s3c24xx_dclk0.parent = &clk_upll;
+	s3c24xx_dclk0.rate   = 12*1000*1000;
+
+	s3c24xx_dclk1.parent = &clk_upll;
+	s3c24xx_dclk1.rate   = 24*1000*1000;
+
+	s3c24xx_clkout0.parent  = &s3c24xx_dclk0;
+	s3c24xx_clkout1.parent  = &s3c24xx_dclk1;
+
+	s3c24xx_uclk.parent  = &s3c24xx_clkout1;
+
+	s3c24xx_register_clocks(osiris_clocks, ARRAY_SIZE(osiris_clocks));
+
+	s3c_device_nand.dev.platform_data = &osiris_nand_info;
+
+	s3c24xx_init_io(osiris_iodesc, ARRAY_SIZE(osiris_iodesc));
+	s3c24xx_init_clocks(0);
+	s3c24xx_init_uarts(osiris_uartcfgs, ARRAY_SIZE(osiris_uartcfgs));
+
+	/* check for the newer revision boards with large page nand */
+
+	if ((__raw_readb(OSIRIS_VA_IDREG) & OSIRIS_ID_REVMASK) >= 4) {
+		printk(KERN_INFO "OSIRIS-B detected (revision %d)\n",
+		       __raw_readb(OSIRIS_VA_IDREG) & OSIRIS_ID_REVMASK);
+		osiris_nand_sets[0].partitions = osiris_default_nand_part_large;
+		osiris_nand_sets[0].nr_partitions = ARRAY_SIZE(osiris_default_nand_part_large);
+	} else {
+		/* write-protect line to the NAND */
+		s3c2410_gpio_setpin(S3C2410_GPA(0), 1);
+	}
+
+	/* fix bus configuration (nBE settings wrong on ABLE pre v2.20) */
+
+	local_irq_save(flags);
+	__raw_writel(__raw_readl(S3C2410_BWSCON) | S3C2410_BWSCON_ST1 | S3C2410_BWSCON_ST2 | S3C2410_BWSCON_ST3 | S3C2410_BWSCON_ST4 | S3C2410_BWSCON_ST5, S3C2410_BWSCON);
+	local_irq_restore(flags);
+}
+
+static void __init osiris_init(void)
+{
+	sysdev_class_register(&osiris_pm_sysclass);
+	sysdev_register(&osiris_pm_sysdev);
+
+	s3c_i2c0_set_platdata(NULL);
+
+	s3c_cpufreq_setboard(&osiris_cpufreq);
+
+	i2c_register_board_info(0, osiris_i2c_devs,
+				ARRAY_SIZE(osiris_i2c_devs));
+
+	platform_add_devices(osiris_devices, ARRAY_SIZE(osiris_devices));
+};
+
+MACHINE_START(OSIRIS, "Simtec-OSIRIS")
+	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= osiris_map_io,
+	.init_irq	= s3c24xx_init_irq,
+	.init_machine	= osiris_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/mach-rx3715.c

@@ -0,0 +1,221 @@
+/* linux/arch/arm/mach-s3c2440/mach-rx3715.c
+ *
+ * Copyright (c) 2003,2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * http://www.handhelds.org/projects/rx3715.html
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/console.h>
+#include <linux/sysdev.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
+
+#include <mach/h1940.h>
+#include <plat/nand.h>
+#include <mach/fb.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/pm.h>
+
+static struct map_desc rx3715_iodesc[] __initdata = {
+	/* dump ISA space somewhere unused */
+
+	{
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
+		.pfn		= __phys_to_pfn(S3C2410_CS3),
+		.length		= SZ_1M,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
+		.pfn		= __phys_to_pfn(S3C2410_CS3),
+		.length		= SZ_1M,
+		.type		= MT_DEVICE,
+	},
+};
+
+
+static struct s3c24xx_uart_clksrc rx3715_serial_clocks[] = {
+	[0] = {
+		.name		= "fclk",
+		.divisor	= 0,
+		.min_baud	= 0,
+		.max_baud	= 0,
+	}
+};
+
+static struct s3c2410_uartcfg rx3715_uartcfgs[] = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+		.clocks	     = rx3715_serial_clocks,
+		.clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x00,
+		.clocks	     = rx3715_serial_clocks,
+		.clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+	},
+	/* IR port */
+	[2] = {
+		.hwport	     = 2,
+		.uart_flags  = UPF_CONS_FLOW,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x43,
+		.ufcon	     = 0x51,
+		.clocks	     = rx3715_serial_clocks,
+		.clocks_size = ARRAY_SIZE(rx3715_serial_clocks),
+	}
+};
+
+/* framebuffer lcd controller information */
+
+static struct s3c2410fb_display rx3715_lcdcfg __initdata = {
+	.lcdcon5 =	S3C2410_LCDCON5_INVVLINE |
+			S3C2410_LCDCON5_FRM565 |
+			S3C2410_LCDCON5_HWSWP,
+
+	.type		= S3C2410_LCDCON1_TFT,
+	.width		= 240,
+	.height		= 320,
+
+	.pixclock	= 260000,
+	.xres		= 240,
+	.yres		= 320,
+	.bpp		= 16,
+	.left_margin	= 36,
+	.right_margin	= 36,
+	.hsync_len	= 8,
+	.upper_margin	= 6,
+	.lower_margin	= 7,
+	.vsync_len	= 3,
+};
+
+static struct s3c2410fb_mach_info rx3715_fb_info __initdata = {
+
+	.displays =	&rx3715_lcdcfg,
+	.num_displays =	1,
+	.default_display = 0,
+
+	.lpcsel =	0xf82,
+
+	.gpccon =	0xaa955699,
+	.gpccon_mask =	0xffc003cc,
+	.gpcup =	0x0000ffff,
+	.gpcup_mask =	0xffffffff,
+
+	.gpdcon =	0xaa95aaa1,
+	.gpdcon_mask =	0xffc0fff0,
+	.gpdup =	0x0000faff,
+	.gpdup_mask =	0xffffffff,
+};
+
+static struct mtd_partition rx3715_nand_part[] = {
+	[0] = {
+		.name		= "Whole Flash",
+		.offset		= 0,
+		.size		= MTDPART_SIZ_FULL,
+		.mask_flags	= MTD_WRITEABLE,
+	}
+};
+
+static struct s3c2410_nand_set rx3715_nand_sets[] = {
+	[0] = {
+		.name		= "Internal",
+		.nr_chips	= 1,
+		.nr_partitions	= ARRAY_SIZE(rx3715_nand_part),
+		.partitions	= rx3715_nand_part,
+	},
+};
+
+static struct s3c2410_platform_nand rx3715_nand_info = {
+	.tacls		= 25,
+	.twrph0		= 50,
+	.twrph1		= 15,
+	.nr_sets	= ARRAY_SIZE(rx3715_nand_sets),
+	.sets		= rx3715_nand_sets,
+};
+
+static struct platform_device *rx3715_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_lcd,
+	&s3c_device_wdt,
+	&s3c_device_i2c0,
+	&s3c_device_iis,
+	&s3c_device_nand,
+};
+
+static void __init rx3715_map_io(void)
+{
+	s3c_device_nand.dev.platform_data = &rx3715_nand_info;
+
+	s3c24xx_init_io(rx3715_iodesc, ARRAY_SIZE(rx3715_iodesc));
+	s3c24xx_init_clocks(16934000);
+	s3c24xx_init_uarts(rx3715_uartcfgs, ARRAY_SIZE(rx3715_uartcfgs));
+}
+
+static void __init rx3715_init_irq(void)
+{
+	s3c24xx_init_irq();
+}
+
+static void __init rx3715_init_machine(void)
+{
+#ifdef CONFIG_PM_H1940
+	memcpy(phys_to_virt(H1940_SUSPEND_RESUMEAT), h1940_pm_return, 1024);
+#endif
+	s3c_pm_init();
+
+	s3c24xx_fb_set_platdata(&rx3715_fb_info);
+	platform_add_devices(rx3715_devices, ARRAY_SIZE(rx3715_devices));
+}
+
+MACHINE_START(RX3715, "IPAQ-RX3715")
+	/* Maintainer: Ben Dooks <ben@fluff.org> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= rx3715_map_io,
+	.init_irq	= rx3715_init_irq,
+	.init_machine	= rx3715_init_machine,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/mach-smdk2440.c

@@ -0,0 +1,186 @@
+/* linux/arch/arm/mach-s3c2440/mach-smdk2440.c
+ *
+ * Copyright (c) 2004,2005 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * http://www.fluff.org/ben/smdk2440/
+ *
+ * Thanks to Dimity Andric and TomTom for the loan of an SMDK2440.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-lcd.h>
+
+#include <mach/idle.h>
+#include <mach/fb.h>
+#include <plat/iic.h>
+
+#include <plat/s3c2410.h>
+#include <plat/s3c2440.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#include <plat/common-smdk.h>
+
+static struct map_desc smdk2440_iodesc[] __initdata = {
+	/* ISA IO Space map (memory space selected by A24) */
+
+	{
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
+		.pfn		= __phys_to_pfn(S3C2410_CS2),
+		.length		= 0x10000,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_WORD + 0x10000,
+		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
+		.length		= SZ_4M,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
+		.pfn		= __phys_to_pfn(S3C2410_CS2),
+		.length		= 0x10000,
+		.type		= MT_DEVICE,
+	}, {
+		.virtual	= (u32)S3C24XX_VA_ISA_BYTE + 0x10000,
+		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
+		.length		= SZ_4M,
+		.type		= MT_DEVICE,
+	}
+};
+
+#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+static struct s3c2410_uartcfg smdk2440_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	/* IR port */
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x43,
+		.ufcon	     = 0x51,
+	}
+};
+
+/* LCD driver info */
+
+static struct s3c2410fb_display smdk2440_lcd_cfg __initdata = {
+
+	.lcdcon5	= S3C2410_LCDCON5_FRM565 |
+			  S3C2410_LCDCON5_INVVLINE |
+			  S3C2410_LCDCON5_INVVFRAME |
+			  S3C2410_LCDCON5_PWREN |
+			  S3C2410_LCDCON5_HWSWP,
+
+	.type		= S3C2410_LCDCON1_TFT,
+
+	.width		= 240,
+	.height		= 320,
+
+	.pixclock	= 166667, /* HCLK 60 MHz, divisor 10 */
+	.xres		= 240,
+	.yres		= 320,
+	.bpp		= 16,
+	.left_margin	= 20,
+	.right_margin	= 8,
+	.hsync_len	= 4,
+	.upper_margin	= 8,
+	.lower_margin	= 7,
+	.vsync_len	= 4,
+};
+
+static struct s3c2410fb_mach_info smdk2440_fb_info __initdata = {
+	.displays	= &smdk2440_lcd_cfg,
+	.num_displays	= 1,
+	.default_display = 0,
+
+#if 0
+	/* currently setup by downloader */
+	.gpccon		= 0xaa940659,
+	.gpccon_mask	= 0xffffffff,
+	.gpcup		= 0x0000ffff,
+	.gpcup_mask	= 0xffffffff,
+	.gpdcon		= 0xaa84aaa0,
+	.gpdcon_mask	= 0xffffffff,
+	.gpdup		= 0x0000faff,
+	.gpdup_mask	= 0xffffffff,
+#endif
+
+	.lpcsel		= ((0xCE6) & ~7) | 1<<4,
+};
+
+static struct platform_device *smdk2440_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_lcd,
+	&s3c_device_wdt,
+	&s3c_device_i2c0,
+	&s3c_device_iis,
+};
+
+static void __init smdk2440_map_io(void)
+{
+	s3c24xx_init_io(smdk2440_iodesc, ARRAY_SIZE(smdk2440_iodesc));
+	s3c24xx_init_clocks(16934400);
+	s3c24xx_init_uarts(smdk2440_uartcfgs, ARRAY_SIZE(smdk2440_uartcfgs));
+}
+
+static void __init smdk2440_machine_init(void)
+{
+	s3c24xx_fb_set_platdata(&smdk2440_fb_info);
+	s3c_i2c0_set_platdata(NULL);
+
+	platform_add_devices(smdk2440_devices, ARRAY_SIZE(smdk2440_devices));
+	smdk_machine_init();
+}
+
+MACHINE_START(S3C2440, "SMDK2440")
+	/* Maintainer: Ben Dooks <ben@fluff.org> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+
+	.init_irq	= s3c24xx_init_irq,
+	.map_io		= smdk2440_map_io,
+	.init_machine	= smdk2440_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

kernel/arch/arm/mach-s3c2440/s3c2440.c

@@ -0,0 +1,52 @@
+/* linux/arch/arm/mach-s3c2440/s3c2440.c
+ *
+ * Copyright (c) 2004-2006 Simtec Electronics
+ *   Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung S3C2440 Mobile CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <asm/irq.h>
+
+#include <plat/s3c2440.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+static struct sys_device s3c2440_sysdev = {
+	.cls		= &s3c2440_sysclass,
+};
+
+int __init s3c2440_init(void)
+{
+	printk("S3C2440: Initialising architecture\n");
+
+	/* change irq for watchdog */
+
+	s3c_device_wdt.resource[1].start = IRQ_S3C2440_WDT;
+	s3c_device_wdt.resource[1].end   = IRQ_S3C2440_WDT;
+
+	/* register our system device for everything else */
+
+	return sysdev_register(&s3c2440_sysdev);
+}