add idl4k kernel firmware version 1.13.0.105

kernel/arch/sh/boards/mach-hdref/Makefile

@@ -0,0 +1,5 @@
+#
+# Makefile for HDRef board
+#
+
+obj-y := setup.o mach.o

kernel/arch/sh/boards/mach-hdref/mach.c

@@ -0,0 +1,60 @@
+/*
+ * arch/sh/boards/st/hdref/mach.c
+ *
+ * Copyright (C) 2007 STMicroelectronics Limited
+ * Author: Stuart Menefy (stuart.menefy@st.com)
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License.  See linux/COPYING for more information.
+ *
+ * Machine vector for the STMicroelectronics HDref board.
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/machvec.h>
+#include <asm/irq-stx7100.h>
+
+static void __iomem *hdref_ioport_map(unsigned long port, unsigned int size)
+{
+#ifdef CONFIG_BLK_DEV_ST40IDE
+        /*
+         * The IDE driver appears to use memory addresses with IO port
+         * calls. This needs fixing.
+         */
+	return (void __iomem *)port;
+#endif
+
+	/* However picking somewhere safe isn't as easy as you might think.
+	 * I used to use external ROM, but that can cause problems if you are
+	 * in the middle of updating Flash. So I'm now using the processor core
+	 * version register, which is guaranted to be available, and non-writable.
+	 */
+	return (void __iomem *)CCN_PVR;
+}
+
+static void __init hdref_init_irq(void)
+{
+	/* enable individual interrupt mode for externals */
+        plat_irq_setup_pins(IRQ_MODE_IRQ);
+
+        /* Set the ILC to route external interrupts to the the INTC */
+        /* Outputs 0-3 are the interrupt pins, 4-7 are routed to the INTC */
+        ilc_route_external(ILC_EXT_IRQ0, 4, 1);	//is jung
+        ilc_route_external(ILC_EXT_IRQ1, 5, 0);
+        ilc_route_external(ILC_EXT_IRQ2, 6, 0);
+        ilc_route_external(ILC_EXT_MDINT, 7, 0);
+
+}
+
+void __init hdref_setup (char **);
+
+struct sh_machine_vector mv_hdref __initmv = {
+        .mv_name                = "ST HDref board",
+        .mv_setup		= hdref_setup,
+	.mv_nr_irqs		= NR_IRQS,
+	.mv_init_irq		= hdref_init_irq,
+	.mv_ioport_map		= hdref_ioport_map,
+};

kernel/arch/sh/boards/mach-hdref/setup.c

@@ -0,0 +1,94 @@
+/*
+ * arch/sh/boards/st/hdref/setup.c
+ *
+ * Copyright (C) 2005 STMicroelectronics Limited
+ * Author: Stuart Menefy (stuart.menefy@st.com)
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License.  See linux/COPYING for more information.
+ *
+ * STMicroelectronics HDref Reference board support.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/phy.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/physmap.h>
+#include <linux/stm/platform.h>
+#include <linux/stm/stx7100.h>
+#include <asm/irl.h>
+
+
+
+void __init hdref_setup(char** cmdline_p)
+{
+	printk("STMicroelectronics HDref Reference board initialisation\n");
+
+	stx7100_early_device_init();
+
+	stx7100_configure_asc(2, &(struct stx7100_asc_config) {
+			.hw_flow_control = 0,
+			.is_console = 1, });
+	stx7100_configure_asc(3, &(struct stx7100_asc_config) {
+			.hw_flow_control = 0,
+			.is_console = 0, });
+}
+
+
+
+static struct platform_device hdref_physmap_flash = {
+	.name		= "physmap-flash",
+	.id		= -1,
+	.num_resources	= 1,
+	.resource	= (struct resource[]) {
+		STM_PLAT_RESOURCE_MEM(0, 8*1024*1024),
+	},
+	.dev.platform_data = &(struct physmap_flash_data) {
+		.width		= 2,
+		.set_vpp	= NULL,
+	},
+};
+
+static struct stmmac_mdio_bus_data stmmac_mdio_bus = {
+	.bus_id = 0,
+	.phy_mask = 0,
+};
+
+static struct platform_device *hdref_devices[] __initdata = {
+	&hdref_physmap_flash,
+};
+
+static int __init hdref_device_init(void)
+{
+	stx7100_configure_sata();
+
+	stx7100_configure_ssc_i2c(0);
+	stx7100_configure_ssc_spi(1, NULL);
+	stx7100_configure_ssc_i2c(2);
+
+	stx7100_configure_usb();
+
+	stx7100_configure_lirc(&(struct stx7100_lirc_config) {
+			.rx_mode = stx7100_lirc_rx_mode_ir,
+			.tx_enabled = 1,
+			.tx_od_enabled = 0, });
+
+	stx7100_configure_pata(&(struct stx7100_pata_config) {
+			.emi_bank = 3,
+			.pc_mode = 1,
+			.irq = IRL1_IRQ, });
+
+	stx7100_configure_ethernet(&(struct stx7100_ethernet_config) {
+			.mode = stx7100_ethernet_mode_mii,
+			.ext_clk = 0,
+			.phy_bus = 0,
+			.phy_addr = -1,
+			.mdio_bus_data = &stmmac_mdio_bus,
+		});
+
+	return platform_add_devices(hdref_devices,
+				    ARRAY_SIZE(hdref_devices));
+}
+device_initcall(hdref_device_init);