add idl4k kernel firmware version 1.13.0.105

kernel/drivers/mtd/onenand/Kconfig

@@ -0,0 +1,73 @@
+#
+# linux/drivers/mtd/onenand/Kconfig
+#
+
+menuconfig MTD_ONENAND
+	tristate "OneNAND Device Support"
+	depends on MTD
+	select MTD_PARTITIONS
+	help
+	  This enables support for accessing all type of OneNAND flash
+	  devices. For further information see
+	  <http://www.samsung.com/Products/Semiconductor/OneNAND/index.htm>
+
+if MTD_ONENAND
+
+config MTD_ONENAND_VERIFY_WRITE
+	bool "Verify OneNAND page writes"
+	help
+	  This adds an extra check when data is written to the flash. The
+	  OneNAND flash device internally checks only bits transitioning
+	  from 1 to 0. There is a rare possibility that even though the
+	  device thinks the write was successful, a bit could have been
+	  flipped accidentally due to device wear or something else.
+
+config MTD_ONENAND_GENERIC
+	tristate "OneNAND Flash device via platform device driver"
+	help
+	  Support for OneNAND flash via platform device driver.
+
+config MTD_ONENAND_OMAP2
+	tristate "OneNAND on OMAP2/OMAP3 support"
+	depends on MTD_ONENAND && (ARCH_OMAP2 || ARCH_OMAP3)
+	help
+	  Support for a OneNAND flash device connected to an OMAP2/OMAP3 CPU
+	  via the GPMC memory controller.
+
+config MTD_ONENAND_OTP
+	bool "OneNAND OTP Support"
+	select HAVE_MTD_OTP
+	help
+	  One Block of the NAND Flash Array memory is reserved as
+	  a One-Time Programmable Block memory area.
+	  Also, 1st Block of NAND Flash Array can be used as OTP.
+
+	  The OTP block can be read, programmed and locked using the same
+	  operations as any other NAND Flash Array memory block.
+	  OTP block cannot be erased.
+
+	  OTP block is fully-guaranteed to be a valid block.
+
+config MTD_ONENAND_2X_PROGRAM
+	bool "OneNAND 2X program support"
+	help
+	  The 2X Program is an extension of Program Operation.
+	  Since the device is equipped with two DataRAMs, and two-plane NAND
+	  Flash memory array, these two component enables simultaneous program
+	  of 4KiB. Plane1 has only even blocks such as block0, block2, block4
+	  while Plane2 has only odd blocks such as block1, block3, block5.
+	  So MTD regards it as 4KiB page size and 256KiB block size
+
+	  Now the following chips support it. (KFXXX16Q2M)
+	    Demux: KFG2G16Q2M, KFH4G16Q2M, KFW8G16Q2M,
+	    Mux:   KFM2G16Q2M, KFN4G16Q2M,
+
+	  And more recent chips
+
+config MTD_ONENAND_SIM
+	tristate "OneNAND simulator support"
+	help
+	  The simulator may simulate various OneNAND flash chips for the
+	  OneNAND MTD layer.
+
+endif # MTD_ONENAND

kernel/drivers/mtd/onenand/Makefile

@@ -0,0 +1,15 @@
+#
+# Makefile for the OneNAND MTD
+#
+
+# Core functionality.
+obj-$(CONFIG_MTD_ONENAND)		+= onenand.o
+
+# Board specific.
+obj-$(CONFIG_MTD_ONENAND_GENERIC)	+= generic.o
+obj-$(CONFIG_MTD_ONENAND_OMAP2)		+= omap2.o
+
+# Simulator
+obj-$(CONFIG_MTD_ONENAND_SIM)		+= onenand_sim.o
+
+onenand-objs = onenand_base.o onenand_bbt.o

kernel/drivers/mtd/onenand/generic.c

@@ -0,0 +1,151 @@
+/*
+ *  linux/drivers/mtd/onenand/generic.c
+ *
+ *  Copyright (c) 2005 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  Overview:
+ *   This is a device driver for the OneNAND flash for generic boards.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+#include <asm/io.h>
+
+/*
+ * Note: Driver name and platform data format have been updated!
+ *
+ * This version of the driver is named "onenand-flash" and takes struct
+ * onenand_platform_data as platform data. The old ARM-specific version
+ * with the name "onenand" used to take struct flash_platform_data.
+ */
+#define DRIVER_NAME	"onenand-flash"
+
+#ifdef CONFIG_MTD_PARTITIONS
+static const char *part_probes[] = { "cmdlinepart", NULL,  };
+#endif
+
+struct onenand_info {
+	struct mtd_info		mtd;
+	struct mtd_partition	*parts;
+	struct onenand_chip	onenand;
+};
+
+static int __devinit generic_onenand_probe(struct platform_device *pdev)
+{
+	struct onenand_info *info;
+	struct onenand_platform_data *pdata = pdev->dev.platform_data;
+	struct resource *res = pdev->resource;
+	unsigned long size = resource_size(res);
+	int err;
+
+	info = kzalloc(sizeof(struct onenand_info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	if (!request_mem_region(res->start, size, dev_name(&pdev->dev))) {
+		err = -EBUSY;
+		goto out_free_info;
+	}
+
+	info->onenand.base = ioremap(res->start, size);
+	if (!info->onenand.base) {
+		err = -ENOMEM;
+		goto out_release_mem_region;
+	}
+
+	info->onenand.mmcontrol = pdata ? pdata->mmcontrol : 0;
+	info->onenand.irq = platform_get_irq(pdev, 0);
+
+	info->mtd.name = dev_name(&pdev->dev);
+	info->mtd.priv = &info->onenand;
+	info->mtd.owner = THIS_MODULE;
+
+	if (onenand_scan(&info->mtd, 1)) {
+		err = -ENXIO;
+		goto out_iounmap;
+	}
+
+#ifdef CONFIG_MTD_PARTITIONS
+	err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0);
+	if (err > 0)
+		add_mtd_partitions(&info->mtd, info->parts, err);
+	else if (err <= 0 && pdata && pdata->parts)
+		add_mtd_partitions(&info->mtd, pdata->parts, pdata->nr_parts);
+	else
+#endif
+		err = add_mtd_device(&info->mtd);
+
+	platform_set_drvdata(pdev, info);
+
+	return 0;
+
+out_iounmap:
+	iounmap(info->onenand.base);
+out_release_mem_region:
+	release_mem_region(res->start, size);
+out_free_info:
+	kfree(info);
+
+	return err;
+}
+
+static int __devexit generic_onenand_remove(struct platform_device *pdev)
+{
+	struct onenand_info *info = platform_get_drvdata(pdev);
+	struct resource *res = pdev->resource;
+	unsigned long size = resource_size(res);
+
+	platform_set_drvdata(pdev, NULL);
+
+	if (info) {
+		if (info->parts)
+			del_mtd_partitions(&info->mtd);
+		else
+			del_mtd_device(&info->mtd);
+
+		onenand_release(&info->mtd);
+		release_mem_region(res->start, size);
+		iounmap(info->onenand.base);
+		kfree(info);
+	}
+
+	return 0;
+}
+
+static struct platform_driver generic_onenand_driver = {
+	.driver = {
+		.name		= DRIVER_NAME,
+		.owner		= THIS_MODULE,
+	},
+	.probe		= generic_onenand_probe,
+	.remove		= __devexit_p(generic_onenand_remove),
+};
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+
+static int __init generic_onenand_init(void)
+{
+	return platform_driver_register(&generic_onenand_driver);
+}
+
+static void __exit generic_onenand_exit(void)
+{
+	platform_driver_unregister(&generic_onenand_driver);
+}
+
+module_init(generic_onenand_init);
+module_exit(generic_onenand_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kyungmin Park <kyungmin.park@samsung.com>");
+MODULE_DESCRIPTION("Glue layer for OneNAND flash on generic boards");

kernel/drivers/mtd/onenand/omap2.c

@@ -0,0 +1,806 @@
+/*
+ *  linux/drivers/mtd/onenand/omap2.c
+ *
+ *  OneNAND driver for OMAP2 / OMAP3
+ *
+ *  Copyright © 2005-2006 Nokia Corporation
+ *
+ *  Author: Jarkko Lavinen <jarkko.lavinen@nokia.com> and Juha Yrjölä
+ *  IRQ and DMA support written by Timo Teras
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program; see the file COPYING. If not, write to the Free Software
+ * Foundation, 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ *
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/io.h>
+
+#include <asm/mach/flash.h>
+#include <mach/gpmc.h>
+#include <mach/onenand.h>
+#include <mach/gpio.h>
+
+#include <mach/dma.h>
+
+#include <mach/board.h>
+
+#define DRIVER_NAME "omap2-onenand"
+
+#define ONENAND_IO_SIZE		SZ_128K
+#define ONENAND_BUFRAM_SIZE	(1024 * 5)
+
+struct omap2_onenand {
+	struct platform_device *pdev;
+	int gpmc_cs;
+	unsigned long phys_base;
+	int gpio_irq;
+	struct mtd_info mtd;
+	struct mtd_partition *parts;
+	struct onenand_chip onenand;
+	struct completion irq_done;
+	struct completion dma_done;
+	int dma_channel;
+	int freq;
+	int (*setup)(void __iomem *base, int freq);
+};
+
+static void omap2_onenand_dma_cb(int lch, u16 ch_status, void *data)
+{
+	struct omap2_onenand *c = data;
+
+	complete(&c->dma_done);
+}
+
+static irqreturn_t omap2_onenand_interrupt(int irq, void *dev_id)
+{
+	struct omap2_onenand *c = dev_id;
+
+	complete(&c->irq_done);
+
+	return IRQ_HANDLED;
+}
+
+static inline unsigned short read_reg(struct omap2_onenand *c, int reg)
+{
+	return readw(c->onenand.base + reg);
+}
+
+static inline void write_reg(struct omap2_onenand *c, unsigned short value,
+			     int reg)
+{
+	writew(value, c->onenand.base + reg);
+}
+
+static void wait_err(char *msg, int state, unsigned int ctrl, unsigned int intr)
+{
+	printk(KERN_ERR "onenand_wait: %s! state %d ctrl 0x%04x intr 0x%04x\n",
+	       msg, state, ctrl, intr);
+}
+
+static void wait_warn(char *msg, int state, unsigned int ctrl,
+		      unsigned int intr)
+{
+	printk(KERN_WARNING "onenand_wait: %s! state %d ctrl 0x%04x "
+	       "intr 0x%04x\n", msg, state, ctrl, intr);
+}
+
+static int omap2_onenand_wait(struct mtd_info *mtd, int state)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	unsigned int intr = 0;
+	unsigned int ctrl;
+	unsigned long timeout;
+	u32 syscfg;
+
+	if (state == FL_RESETING) {
+		int i;
+
+		for (i = 0; i < 20; i++) {
+			udelay(1);
+			intr = read_reg(c, ONENAND_REG_INTERRUPT);
+			if (intr & ONENAND_INT_MASTER)
+				break;
+		}
+		ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+		if (ctrl & ONENAND_CTRL_ERROR) {
+			wait_err("controller error", state, ctrl, intr);
+			return -EIO;
+		}
+		if (!(intr & ONENAND_INT_RESET)) {
+			wait_err("timeout", state, ctrl, intr);
+			return -EIO;
+		}
+		return 0;
+	}
+
+	if (state != FL_READING) {
+		int result;
+
+		/* Turn interrupts on */
+		syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
+		if (!(syscfg & ONENAND_SYS_CFG1_IOBE)) {
+			syscfg |= ONENAND_SYS_CFG1_IOBE;
+			write_reg(c, syscfg, ONENAND_REG_SYS_CFG1);
+			if (cpu_is_omap34xx())
+				/* Add a delay to let GPIO settle */
+				syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
+		}
+
+		INIT_COMPLETION(c->irq_done);
+		if (c->gpio_irq) {
+			result = gpio_get_value(c->gpio_irq);
+			if (result == -1) {
+				ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+				intr = read_reg(c, ONENAND_REG_INTERRUPT);
+				wait_err("gpio error", state, ctrl, intr);
+				return -EIO;
+			}
+		} else
+			result = 0;
+		if (result == 0) {
+			int retry_cnt = 0;
+retry:
+			result = wait_for_completion_timeout(&c->irq_done,
+						    msecs_to_jiffies(20));
+			if (result == 0) {
+				/* Timeout after 20ms */
+				ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+				if (ctrl & ONENAND_CTRL_ONGO) {
+					/*
+					 * The operation seems to be still going
+					 * so give it some more time.
+					 */
+					retry_cnt += 1;
+					if (retry_cnt < 3)
+						goto retry;
+					intr = read_reg(c,
+							ONENAND_REG_INTERRUPT);
+					wait_err("timeout", state, ctrl, intr);
+					return -EIO;
+				}
+				intr = read_reg(c, ONENAND_REG_INTERRUPT);
+				if ((intr & ONENAND_INT_MASTER) == 0)
+					wait_warn("timeout", state, ctrl, intr);
+			}
+		}
+	} else {
+		int retry_cnt = 0;
+
+		/* Turn interrupts off */
+		syscfg = read_reg(c, ONENAND_REG_SYS_CFG1);
+		syscfg &= ~ONENAND_SYS_CFG1_IOBE;
+		write_reg(c, syscfg, ONENAND_REG_SYS_CFG1);
+
+		timeout = jiffies + msecs_to_jiffies(20);
+		while (1) {
+			if (time_before(jiffies, timeout)) {
+				intr = read_reg(c, ONENAND_REG_INTERRUPT);
+				if (intr & ONENAND_INT_MASTER)
+					break;
+			} else {
+				/* Timeout after 20ms */
+				ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+				if (ctrl & ONENAND_CTRL_ONGO) {
+					/*
+					 * The operation seems to be still going
+					 * so give it some more time.
+					 */
+					retry_cnt += 1;
+					if (retry_cnt < 3) {
+						timeout = jiffies +
+							  msecs_to_jiffies(20);
+						continue;
+					}
+				}
+				break;
+			}
+		}
+	}
+
+	intr = read_reg(c, ONENAND_REG_INTERRUPT);
+	ctrl = read_reg(c, ONENAND_REG_CTRL_STATUS);
+
+	if (intr & ONENAND_INT_READ) {
+		int ecc = read_reg(c, ONENAND_REG_ECC_STATUS);
+
+		if (ecc) {
+			unsigned int addr1, addr8;
+
+			addr1 = read_reg(c, ONENAND_REG_START_ADDRESS1);
+			addr8 = read_reg(c, ONENAND_REG_START_ADDRESS8);
+			if (ecc & ONENAND_ECC_2BIT_ALL) {
+				printk(KERN_ERR "onenand_wait: ECC error = "
+				       "0x%04x, addr1 %#x, addr8 %#x\n",
+				       ecc, addr1, addr8);
+				mtd->ecc_stats.failed++;
+				return -EBADMSG;
+			} else if (ecc & ONENAND_ECC_1BIT_ALL) {
+				printk(KERN_NOTICE "onenand_wait: correctable "
+				       "ECC error = 0x%04x, addr1 %#x, "
+				       "addr8 %#x\n", ecc, addr1, addr8);
+				mtd->ecc_stats.corrected++;
+			}
+		}
+	} else if (state == FL_READING) {
+		wait_err("timeout", state, ctrl, intr);
+		return -EIO;
+	}
+
+	if (ctrl & ONENAND_CTRL_ERROR) {
+		wait_err("controller error", state, ctrl, intr);
+		if (ctrl & ONENAND_CTRL_LOCK)
+			printk(KERN_ERR "onenand_wait: "
+					"Device is write protected!!!\n");
+		return -EIO;
+	}
+
+	if (ctrl & 0xFE9F)
+		wait_warn("unexpected controller status", state, ctrl, intr);
+
+	return 0;
+}
+
+static inline int omap2_onenand_bufferram_offset(struct mtd_info *mtd, int area)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	if (ONENAND_CURRENT_BUFFERRAM(this)) {
+		if (area == ONENAND_DATARAM)
+			return this->writesize;
+		if (area == ONENAND_SPARERAM)
+			return mtd->oobsize;
+	}
+
+	return 0;
+}
+
+#if defined(CONFIG_ARCH_OMAP3) || defined(MULTI_OMAP2)
+
+static int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area,
+					unsigned char *buffer, int offset,
+					size_t count)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	dma_addr_t dma_src, dma_dst;
+	int bram_offset;
+	unsigned long timeout;
+	void *buf = (void *)buffer;
+	size_t xtra;
+	volatile unsigned *done;
+
+	bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
+	if (bram_offset & 3 || (size_t)buf & 3 || count < 384)
+		goto out_copy;
+
+	/* panic_write() may be in an interrupt context */
+	if (in_interrupt())
+		goto out_copy;
+
+	if (buf >= high_memory) {
+		struct page *p1;
+
+		if (((size_t)buf & PAGE_MASK) !=
+		    ((size_t)(buf + count - 1) & PAGE_MASK))
+			goto out_copy;
+		p1 = vmalloc_to_page(buf);
+		if (!p1)
+			goto out_copy;
+		buf = page_address(p1) + ((size_t)buf & ~PAGE_MASK);
+	}
+
+	xtra = count & 3;
+	if (xtra) {
+		count -= xtra;
+		memcpy(buf + count, this->base + bram_offset + count, xtra);
+	}
+
+	dma_src = c->phys_base + bram_offset;
+	dma_dst = dma_map_single(&c->pdev->dev, buf, count, DMA_FROM_DEVICE);
+	if (dma_mapping_error(&c->pdev->dev, dma_dst)) {
+		dev_err(&c->pdev->dev,
+			"Couldn't DMA map a %d byte buffer\n",
+			count);
+		goto out_copy;
+	}
+
+	omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S32,
+				     count >> 2, 1, 0, 0, 0);
+	omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				dma_src, 0, 0);
+	omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				 dma_dst, 0, 0);
+
+	INIT_COMPLETION(c->dma_done);
+	omap_start_dma(c->dma_channel);
+
+	timeout = jiffies + msecs_to_jiffies(20);
+	done = &c->dma_done.done;
+	while (time_before(jiffies, timeout))
+		if (*done)
+			break;
+
+	dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_FROM_DEVICE);
+
+	if (!*done) {
+		dev_err(&c->pdev->dev, "timeout waiting for DMA\n");
+		goto out_copy;
+	}
+
+	return 0;
+
+out_copy:
+	memcpy(buf, this->base + bram_offset, count);
+	return 0;
+}
+
+static int omap3_onenand_write_bufferram(struct mtd_info *mtd, int area,
+					 const unsigned char *buffer,
+					 int offset, size_t count)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	dma_addr_t dma_src, dma_dst;
+	int bram_offset;
+	unsigned long timeout;
+	void *buf = (void *)buffer;
+	volatile unsigned *done;
+
+	bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
+	if (bram_offset & 3 || (size_t)buf & 3 || count < 384)
+		goto out_copy;
+
+	/* panic_write() may be in an interrupt context */
+	if (in_interrupt())
+		goto out_copy;
+
+	if (buf >= high_memory) {
+		struct page *p1;
+
+		if (((size_t)buf & PAGE_MASK) !=
+		    ((size_t)(buf + count - 1) & PAGE_MASK))
+			goto out_copy;
+		p1 = vmalloc_to_page(buf);
+		if (!p1)
+			goto out_copy;
+		buf = page_address(p1) + ((size_t)buf & ~PAGE_MASK);
+	}
+
+	dma_src = dma_map_single(&c->pdev->dev, buf, count, DMA_TO_DEVICE);
+	dma_dst = c->phys_base + bram_offset;
+	if (dma_mapping_error(&c->pdev->dev, dma_dst)) {
+		dev_err(&c->pdev->dev,
+			"Couldn't DMA map a %d byte buffer\n",
+			count);
+		return -1;
+	}
+
+	omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S32,
+				     count >> 2, 1, 0, 0, 0);
+	omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				dma_src, 0, 0);
+	omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				 dma_dst, 0, 0);
+
+	INIT_COMPLETION(c->dma_done);
+	omap_start_dma(c->dma_channel);
+
+	timeout = jiffies + msecs_to_jiffies(20);
+	done = &c->dma_done.done;
+	while (time_before(jiffies, timeout))
+		if (*done)
+			break;
+
+	dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_TO_DEVICE);
+
+	if (!*done) {
+		dev_err(&c->pdev->dev, "timeout waiting for DMA\n");
+		goto out_copy;
+	}
+
+	return 0;
+
+out_copy:
+	memcpy(this->base + bram_offset, buf, count);
+	return 0;
+}
+
+#else
+
+int omap3_onenand_read_bufferram(struct mtd_info *mtd, int area,
+				 unsigned char *buffer, int offset,
+				 size_t count);
+
+int omap3_onenand_write_bufferram(struct mtd_info *mtd, int area,
+				  const unsigned char *buffer,
+				  int offset, size_t count);
+
+#endif
+
+#if defined(CONFIG_ARCH_OMAP2) || defined(MULTI_OMAP2)
+
+static int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area,
+					unsigned char *buffer, int offset,
+					size_t count)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	dma_addr_t dma_src, dma_dst;
+	int bram_offset;
+
+	bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
+	/* DMA is not used.  Revisit PM requirements before enabling it. */
+	if (1 || (c->dma_channel < 0) ||
+	    ((void *) buffer >= (void *) high_memory) || (bram_offset & 3) ||
+	    (((unsigned int) buffer) & 3) || (count < 1024) || (count & 3)) {
+		memcpy(buffer, (__force void *)(this->base + bram_offset),
+		       count);
+		return 0;
+	}
+
+	dma_src = c->phys_base + bram_offset;
+	dma_dst = dma_map_single(&c->pdev->dev, buffer, count,
+				 DMA_FROM_DEVICE);
+	if (dma_mapping_error(&c->pdev->dev, dma_dst)) {
+		dev_err(&c->pdev->dev,
+			"Couldn't DMA map a %d byte buffer\n",
+			count);
+		return -1;
+	}
+
+	omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S32,
+				     count / 4, 1, 0, 0, 0);
+	omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				dma_src, 0, 0);
+	omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				 dma_dst, 0, 0);
+
+	INIT_COMPLETION(c->dma_done);
+	omap_start_dma(c->dma_channel);
+	wait_for_completion(&c->dma_done);
+
+	dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_FROM_DEVICE);
+
+	return 0;
+}
+
+static int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area,
+					 const unsigned char *buffer,
+					 int offset, size_t count)
+{
+	struct omap2_onenand *c = container_of(mtd, struct omap2_onenand, mtd);
+	struct onenand_chip *this = mtd->priv;
+	dma_addr_t dma_src, dma_dst;
+	int bram_offset;
+
+	bram_offset = omap2_onenand_bufferram_offset(mtd, area) + area + offset;
+	/* DMA is not used.  Revisit PM requirements before enabling it. */
+	if (1 || (c->dma_channel < 0) ||
+	    ((void *) buffer >= (void *) high_memory) || (bram_offset & 3) ||
+	    (((unsigned int) buffer) & 3) || (count < 1024) || (count & 3)) {
+		memcpy((__force void *)(this->base + bram_offset), buffer,
+		       count);
+		return 0;
+	}
+
+	dma_src = dma_map_single(&c->pdev->dev, (void *) buffer, count,
+				 DMA_TO_DEVICE);
+	dma_dst = c->phys_base + bram_offset;
+	if (dma_mapping_error(&c->pdev->dev, dma_dst)) {
+		dev_err(&c->pdev->dev,
+			"Couldn't DMA map a %d byte buffer\n",
+			count);
+		return -1;
+	}
+
+	omap_set_dma_transfer_params(c->dma_channel, OMAP_DMA_DATA_TYPE_S16,
+				     count / 2, 1, 0, 0, 0);
+	omap_set_dma_src_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				dma_src, 0, 0);
+	omap_set_dma_dest_params(c->dma_channel, 0, OMAP_DMA_AMODE_POST_INC,
+				 dma_dst, 0, 0);
+
+	INIT_COMPLETION(c->dma_done);
+	omap_start_dma(c->dma_channel);
+	wait_for_completion(&c->dma_done);
+
+	dma_unmap_single(&c->pdev->dev, dma_dst, count, DMA_TO_DEVICE);
+
+	return 0;
+}
+
+#else
+
+int omap2_onenand_read_bufferram(struct mtd_info *mtd, int area,
+				 unsigned char *buffer, int offset,
+				 size_t count);
+
+int omap2_onenand_write_bufferram(struct mtd_info *mtd, int area,
+				  const unsigned char *buffer,
+				  int offset, size_t count);
+
+#endif
+
+static struct platform_driver omap2_onenand_driver;
+
+static int __adjust_timing(struct device *dev, void *data)
+{
+	int ret = 0;
+	struct omap2_onenand *c;
+
+	c = dev_get_drvdata(dev);
+
+	BUG_ON(c->setup == NULL);
+
+	/* DMA is not in use so this is all that is needed */
+	/* Revisit for OMAP3! */
+	ret = c->setup(c->onenand.base, c->freq);
+
+	return ret;
+}
+
+int omap2_onenand_rephase(void)
+{
+	return driver_for_each_device(&omap2_onenand_driver.driver, NULL,
+				      NULL, __adjust_timing);
+}
+
+static void omap2_onenand_shutdown(struct platform_device *pdev)
+{
+	struct omap2_onenand *c = dev_get_drvdata(&pdev->dev);
+
+	/* With certain content in the buffer RAM, the OMAP boot ROM code
+	 * can recognize the flash chip incorrectly. Zero it out before
+	 * soft reset.
+	 */
+	memset((__force void *)c->onenand.base, 0, ONENAND_BUFRAM_SIZE);
+}
+
+static int __devinit omap2_onenand_probe(struct platform_device *pdev)
+{
+	struct omap_onenand_platform_data *pdata;
+	struct omap2_onenand *c;
+	int r;
+
+	pdata = pdev->dev.platform_data;
+	if (pdata == NULL) {
+		dev_err(&pdev->dev, "platform data missing\n");
+		return -ENODEV;
+	}
+
+	c = kzalloc(sizeof(struct omap2_onenand), GFP_KERNEL);
+	if (!c)
+		return -ENOMEM;
+
+	init_completion(&c->irq_done);
+	init_completion(&c->dma_done);
+	c->gpmc_cs = pdata->cs;
+	c->gpio_irq = pdata->gpio_irq;
+	c->dma_channel = pdata->dma_channel;
+	if (c->dma_channel < 0) {
+		/* if -1, don't use DMA */
+		c->gpio_irq = 0;
+	}
+
+	r = gpmc_cs_request(c->gpmc_cs, ONENAND_IO_SIZE, &c->phys_base);
+	if (r < 0) {
+		dev_err(&pdev->dev, "Cannot request GPMC CS\n");
+		goto err_kfree;
+	}
+
+	if (request_mem_region(c->phys_base, ONENAND_IO_SIZE,
+			       pdev->dev.driver->name) == NULL) {
+		dev_err(&pdev->dev, "Cannot reserve memory region at 0x%08lx, "
+			"size: 0x%x\n",	c->phys_base, ONENAND_IO_SIZE);
+		r = -EBUSY;
+		goto err_free_cs;
+	}
+	c->onenand.base = ioremap(c->phys_base, ONENAND_IO_SIZE);
+	if (c->onenand.base == NULL) {
+		r = -ENOMEM;
+		goto err_release_mem_region;
+	}
+
+	if (pdata->onenand_setup != NULL) {
+		r = pdata->onenand_setup(c->onenand.base, c->freq);
+		if (r < 0) {
+			dev_err(&pdev->dev, "Onenand platform setup failed: "
+				"%d\n", r);
+			goto err_iounmap;
+		}
+		c->setup = pdata->onenand_setup;
+	}
+
+	if (c->gpio_irq) {
+		if ((r = gpio_request(c->gpio_irq, "OneNAND irq")) < 0) {
+			dev_err(&pdev->dev,  "Failed to request GPIO%d for "
+				"OneNAND\n", c->gpio_irq);
+			goto err_iounmap;
+	}
+	gpio_direction_input(c->gpio_irq);
+
+	if ((r = request_irq(gpio_to_irq(c->gpio_irq),
+			     omap2_onenand_interrupt, IRQF_TRIGGER_RISING,
+			     pdev->dev.driver->name, c)) < 0)
+		goto err_release_gpio;
+	}
+
+	if (c->dma_channel >= 0) {
+		r = omap_request_dma(0, pdev->dev.driver->name,
+				     omap2_onenand_dma_cb, (void *) c,
+				     &c->dma_channel);
+		if (r == 0) {
+			omap_set_dma_write_mode(c->dma_channel,
+						OMAP_DMA_WRITE_NON_POSTED);
+			omap_set_dma_src_data_pack(c->dma_channel, 1);
+			omap_set_dma_src_burst_mode(c->dma_channel,
+						    OMAP_DMA_DATA_BURST_8);
+			omap_set_dma_dest_data_pack(c->dma_channel, 1);
+			omap_set_dma_dest_burst_mode(c->dma_channel,
+						     OMAP_DMA_DATA_BURST_8);
+		} else {
+			dev_info(&pdev->dev,
+				 "failed to allocate DMA for OneNAND, "
+				 "using PIO instead\n");
+			c->dma_channel = -1;
+		}
+	}
+
+	dev_info(&pdev->dev, "initializing on CS%d, phys base 0x%08lx, virtual "
+		 "base %p\n", c->gpmc_cs, c->phys_base,
+		 c->onenand.base);
+
+	c->pdev = pdev;
+	c->mtd.name = dev_name(&pdev->dev);
+	c->mtd.priv = &c->onenand;
+	c->mtd.owner = THIS_MODULE;
+
+	c->mtd.dev.parent = &pdev->dev;
+
+	if (c->dma_channel >= 0) {
+		struct onenand_chip *this = &c->onenand;
+
+		this->wait = omap2_onenand_wait;
+		if (cpu_is_omap34xx()) {
+			this->read_bufferram = omap3_onenand_read_bufferram;
+			this->write_bufferram = omap3_onenand_write_bufferram;
+		} else {
+			this->read_bufferram = omap2_onenand_read_bufferram;
+			this->write_bufferram = omap2_onenand_write_bufferram;
+		}
+	}
+
+	if ((r = onenand_scan(&c->mtd, 1)) < 0)
+		goto err_release_dma;
+
+	switch ((c->onenand.version_id >> 4) & 0xf) {
+	case 0:
+		c->freq = 40;
+		break;
+	case 1:
+		c->freq = 54;
+		break;
+	case 2:
+		c->freq = 66;
+		break;
+	case 3:
+		c->freq = 83;
+		break;
+	}
+
+#ifdef CONFIG_MTD_PARTITIONS
+	if (pdata->parts != NULL)
+		r = add_mtd_partitions(&c->mtd, pdata->parts,
+				       pdata->nr_parts);
+	else
+#endif
+		r = add_mtd_device(&c->mtd);
+	if (r < 0)
+		goto err_release_onenand;
+
+	platform_set_drvdata(pdev, c);
+
+	return 0;
+
+err_release_onenand:
+	onenand_release(&c->mtd);
+err_release_dma:
+	if (c->dma_channel != -1)
+		omap_free_dma(c->dma_channel);
+	if (c->gpio_irq)
+		free_irq(gpio_to_irq(c->gpio_irq), c);
+err_release_gpio:
+	if (c->gpio_irq)
+		gpio_free(c->gpio_irq);
+err_iounmap:
+	iounmap(c->onenand.base);
+err_release_mem_region:
+	release_mem_region(c->phys_base, ONENAND_IO_SIZE);
+err_free_cs:
+	gpmc_cs_free(c->gpmc_cs);
+err_kfree:
+	kfree(c);
+
+	return r;
+}
+
+static int __devexit omap2_onenand_remove(struct platform_device *pdev)
+{
+	struct omap2_onenand *c = dev_get_drvdata(&pdev->dev);
+
+	BUG_ON(c == NULL);
+
+#ifdef CONFIG_MTD_PARTITIONS
+	if (c->parts)
+		del_mtd_partitions(&c->mtd);
+	else
+		del_mtd_device(&c->mtd);
+#else
+	del_mtd_device(&c->mtd);
+#endif
+
+	onenand_release(&c->mtd);
+	if (c->dma_channel != -1)
+		omap_free_dma(c->dma_channel);
+	omap2_onenand_shutdown(pdev);
+	platform_set_drvdata(pdev, NULL);
+	if (c->gpio_irq) {
+		free_irq(gpio_to_irq(c->gpio_irq), c);
+		gpio_free(c->gpio_irq);
+	}
+	iounmap(c->onenand.base);
+	release_mem_region(c->phys_base, ONENAND_IO_SIZE);
+	gpmc_cs_free(c->gpmc_cs);
+	kfree(c);
+
+	return 0;
+}
+
+static struct platform_driver omap2_onenand_driver = {
+	.probe		= omap2_onenand_probe,
+	.remove		= __devexit_p(omap2_onenand_remove),
+	.shutdown	= omap2_onenand_shutdown,
+	.driver		= {
+		.name	= DRIVER_NAME,
+		.owner  = THIS_MODULE,
+	},
+};
+
+static int __init omap2_onenand_init(void)
+{
+	printk(KERN_INFO "OneNAND driver initializing\n");
+	return platform_driver_register(&omap2_onenand_driver);
+}
+
+static void __exit omap2_onenand_exit(void)
+{
+	platform_driver_unregister(&omap2_onenand_driver);
+}
+
+module_init(omap2_onenand_init);
+module_exit(omap2_onenand_exit);
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Jarkko Lavinen <jarkko.lavinen@nokia.com>");
+MODULE_DESCRIPTION("Glue layer for OneNAND flash on OMAP2 / OMAP3");

kernel/drivers/mtd/onenand/onenand_bbt.c

@@ -0,0 +1,253 @@
+/*
+ *  linux/drivers/mtd/onenand/onenand_bbt.c
+ *
+ *  Bad Block Table support for the OneNAND driver
+ *
+ *  Copyright(c) 2005 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ *  Derived from nand_bbt.c
+ *
+ *  TODO:
+ *    Split BBT core and chip specific BBT.
+ */
+
+#include <linux/slab.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/compatmac.h>
+
+/**
+ * check_short_pattern - [GENERIC] check if a pattern is in the buffer
+ * @param buf		the buffer to search
+ * @param len		the length of buffer to search
+ * @param paglen	the pagelength
+ * @param td		search pattern descriptor
+ *
+ * Check for a pattern at the given place. Used to search bad block
+ * tables and good / bad block identifiers. Same as check_pattern, but
+ * no optional empty check and the pattern is expected to start
+ * at offset 0.
+ *
+ */
+static int check_short_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_descr *td)
+{
+	int i;
+	uint8_t *p = buf;
+
+	/* Compare the pattern */
+	for (i = 0; i < td->len; i++) {
+		if (p[i] != td->pattern[i])
+			return -1;
+	}
+        return 0;
+}
+
+/**
+ * create_bbt - [GENERIC] Create a bad block table by scanning the device
+ * @param mtd		MTD device structure
+ * @param buf		temporary buffer
+ * @param bd		descriptor for the good/bad block search pattern
+ * @param chip		create the table for a specific chip, -1 read all chips.
+ *              Applies only if NAND_BBT_PERCHIP option is set
+ *
+ * Create a bad block table by scanning the device
+ * for the given good/bad block identify pattern
+ */
+static int create_bbt(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_descr *bd, int chip)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	int i, j, numblocks, len, scanlen;
+	int startblock;
+	loff_t from;
+	size_t readlen, ooblen;
+	struct mtd_oob_ops ops;
+	int rgn;
+
+	printk(KERN_INFO "Scanning device for bad blocks\n");
+
+	len = 2;
+
+	/* We need only read few bytes from the OOB area */
+	scanlen = ooblen = 0;
+	readlen = bd->len;
+
+	/* chip == -1 case only */
+	/* Note that numblocks is 2 * (real numblocks) here;
+	 * see i += 2 below as it makses shifting and masking less painful
+	 */
+	numblocks = this->chipsize >> (bbm->bbt_erase_shift - 1);
+	startblock = 0;
+	from = 0;
+
+	ops.mode = MTD_OOB_PLACE;
+	ops.ooblen = readlen;
+	ops.oobbuf = buf;
+	ops.len = ops.ooboffs = ops.retlen = ops.oobretlen = 0;
+
+	for (i = startblock; i < numblocks; ) {
+		int ret;
+
+		for (j = 0; j < len; j++) {
+			/* No need to read pages fully,
+			 * just read required OOB bytes */
+			ret = onenand_bbt_read_oob(mtd, from + j * mtd->writesize + bd->offs, &ops);
+
+			/* If it is a initial bad block, just ignore it */
+			if (ret == ONENAND_BBT_READ_FATAL_ERROR)
+				return -EIO;
+
+			if (ret || check_short_pattern(&buf[j * scanlen], scanlen, mtd->writesize, bd)) {
+				bbm->bbt[i >> 3] |= 0x03 << (i & 0x6);
+				printk(KERN_WARNING "Bad eraseblock %d at 0x%08x\n",
+					i >> 1, (unsigned int) from);
+				mtd->ecc_stats.badblocks++;
+				break;
+			}
+		}
+		i += 2;
+
+		if (FLEXONENAND(this)) {
+			rgn = flexonenand_region(mtd, from);
+			from += mtd->eraseregions[rgn].erasesize;
+		} else
+			from += (1 << bbm->bbt_erase_shift);
+	}
+
+	return 0;
+}
+
+
+/**
+ * onenand_memory_bbt - [GENERIC] create a memory based bad block table
+ * @param mtd		MTD device structure
+ * @param bd		descriptor for the good/bad block search pattern
+ *
+ * The function creates a memory based bbt by scanning the device
+ * for manufacturer / software marked good / bad blocks
+ */
+static inline int onenand_memory_bbt (struct mtd_info *mtd, struct nand_bbt_descr *bd)
+{
+	struct onenand_chip *this = mtd->priv;
+
+        bd->options &= ~NAND_BBT_SCANEMPTY;
+	return create_bbt(mtd, this->page_buf, bd, -1);
+}
+
+/**
+ * onenand_isbad_bbt - [OneNAND Interface] Check if a block is bad
+ * @param mtd		MTD device structure
+ * @param offs		offset in the device
+ * @param allowbbt	allow access to bad block table region
+ */
+static int onenand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	int block;
+	uint8_t res;
+
+	/* Get block number * 2 */
+	block = (int) (onenand_block(this, offs) << 1);
+	res = (bbm->bbt[block >> 3] >> (block & 0x06)) & 0x03;
+
+	DEBUG(MTD_DEBUG_LEVEL2, "onenand_isbad_bbt: bbt info for offs 0x%08x: (block %d) 0x%02x\n",
+		(unsigned int) offs, block >> 1, res);
+
+	switch ((int) res) {
+	case 0x00:	return 0;
+	case 0x01:	return 1;
+	case 0x02:	return allowbbt ? 0 : 1;
+	}
+
+	return 1;
+}
+
+/**
+ * onenand_scan_bbt - [OneNAND Interface] scan, find, read and maybe create bad block table(s)
+ * @param mtd		MTD device structure
+ * @param bd		descriptor for the good/bad block search pattern
+ *
+ * The function checks, if a bad block table(s) is/are already
+ * available. If not it scans the device for manufacturer
+ * marked good / bad blocks and writes the bad block table(s) to
+ * the selected place.
+ *
+ * The bad block table memory is allocated here. It is freed
+ * by the onenand_release function.
+ *
+ */
+int onenand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm = this->bbm;
+	int len, ret = 0;
+
+	len = this->chipsize >> (this->erase_shift + 2);
+	/* Allocate memory (2bit per block) and clear the memory bad block table */
+	bbm->bbt = kzalloc(len, GFP_KERNEL);
+	if (!bbm->bbt) {
+		printk(KERN_ERR "onenand_scan_bbt: Out of memory\n");
+		return -ENOMEM;
+	}
+
+	/* Set the bad block position */
+	bbm->badblockpos = ONENAND_BADBLOCK_POS;
+
+	/* Set erase shift */
+	bbm->bbt_erase_shift = this->erase_shift;
+
+	if (!bbm->isbad_bbt)
+		bbm->isbad_bbt = onenand_isbad_bbt;
+
+	/* Scan the device to build a memory based bad block table */
+	if ((ret = onenand_memory_bbt(mtd, bd))) {
+		printk(KERN_ERR "onenand_scan_bbt: Can't scan flash and build the RAM-based BBT\n");
+		kfree(bbm->bbt);
+		bbm->bbt = NULL;
+	}
+
+	return ret;
+}
+
+/*
+ * Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks.
+ */
+static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
+
+static struct nand_bbt_descr largepage_memorybased = {
+	.options = 0,
+	.offs = 0,
+	.len = 2,
+	.pattern = scan_ff_pattern,
+};
+
+/**
+ * onenand_default_bbt - [OneNAND Interface] Select a default bad block table for the device
+ * @param mtd		MTD device structure
+ *
+ * This function selects the default bad block table
+ * support for the device and calls the onenand_scan_bbt function
+ */
+int onenand_default_bbt(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	struct bbm_info *bbm;
+
+	this->bbm = kzalloc(sizeof(struct bbm_info), GFP_KERNEL);
+	if (!this->bbm)
+		return -ENOMEM;
+
+	bbm = this->bbm;
+
+	/* 1KB page has same configuration as 2KB page */
+	if (!bbm->badblock_pattern)
+		bbm->badblock_pattern = &largepage_memorybased;
+
+	return onenand_scan_bbt(mtd, bbm->badblock_pattern);
+}
+
+EXPORT_SYMBOL(onenand_scan_bbt);
+EXPORT_SYMBOL(onenand_default_bbt);

kernel/drivers/mtd/onenand/onenand_sim.c

@@ -0,0 +1,562 @@
+/*
+ *  linux/drivers/mtd/onenand/onenand_sim.c
+ *
+ *  The OneNAND simulator
+ *
+ *  Copyright © 2005-2007 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *
+ *  Vishak G <vishak.g at samsung.com>, Rohit Hagargundgi <h.rohit at samsung.com>
+ *  Flex-OneNAND simulator support
+ *  Copyright (C) Samsung Electronics, 2008
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/vmalloc.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/onenand.h>
+
+#include <linux/io.h>
+
+#ifndef CONFIG_ONENAND_SIM_MANUFACTURER
+#define CONFIG_ONENAND_SIM_MANUFACTURER         0xec
+#endif
+
+#ifndef CONFIG_ONENAND_SIM_DEVICE_ID
+#define CONFIG_ONENAND_SIM_DEVICE_ID            0x04
+#endif
+
+#define CONFIG_FLEXONENAND ((CONFIG_ONENAND_SIM_DEVICE_ID >> 9) & 1)
+
+#ifndef CONFIG_ONENAND_SIM_VERSION_ID
+#define CONFIG_ONENAND_SIM_VERSION_ID           0x1e
+#endif
+
+#ifndef CONFIG_ONENAND_SIM_TECHNOLOGY_ID
+#define CONFIG_ONENAND_SIM_TECHNOLOGY_ID CONFIG_FLEXONENAND
+#endif
+
+/* Initial boundary values for Flex-OneNAND Simulator */
+#ifndef CONFIG_FLEXONENAND_SIM_DIE0_BOUNDARY
+#define CONFIG_FLEXONENAND_SIM_DIE0_BOUNDARY	0x01
+#endif
+
+#ifndef CONFIG_FLEXONENAND_SIM_DIE1_BOUNDARY
+#define CONFIG_FLEXONENAND_SIM_DIE1_BOUNDARY	0x01
+#endif
+
+static int manuf_id	= CONFIG_ONENAND_SIM_MANUFACTURER;
+static int device_id	= CONFIG_ONENAND_SIM_DEVICE_ID;
+static int version_id	= CONFIG_ONENAND_SIM_VERSION_ID;
+static int technology_id = CONFIG_ONENAND_SIM_TECHNOLOGY_ID;
+static int boundary[] = {
+	CONFIG_FLEXONENAND_SIM_DIE0_BOUNDARY,
+	CONFIG_FLEXONENAND_SIM_DIE1_BOUNDARY,
+};
+
+struct onenand_flash {
+	void __iomem *base;
+	void __iomem *data;
+};
+
+#define ONENAND_CORE(flash)		(flash->data)
+#define ONENAND_CORE_SPARE(flash, this, offset)				\
+	((flash->data) + (this->chipsize) + (offset >> 5))
+
+#define ONENAND_MAIN_AREA(this, offset)					\
+	(this->base + ONENAND_DATARAM + offset)
+
+#define ONENAND_SPARE_AREA(this, offset)				\
+	(this->base + ONENAND_SPARERAM + offset)
+
+#define ONENAND_GET_WP_STATUS(this)					\
+	(readw(this->base + ONENAND_REG_WP_STATUS))
+
+#define ONENAND_SET_WP_STATUS(v, this)					\
+	(writew(v, this->base + ONENAND_REG_WP_STATUS))
+
+/* It has all 0xff chars */
+#define MAX_ONENAND_PAGESIZE		(4096 + 128)
+static unsigned char *ffchars;
+
+#if CONFIG_FLEXONENAND
+#define PARTITION_NAME "Flex-OneNAND simulator partition"
+#else
+#define PARTITION_NAME "OneNAND simulator partition"
+#endif
+
+static struct mtd_partition os_partitions[] = {
+	{
+		.name		= PARTITION_NAME,
+		.offset		= 0,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+/*
+ * OneNAND simulator mtd
+ */
+struct onenand_info {
+	struct mtd_info		mtd;
+	struct mtd_partition	*parts;
+	struct onenand_chip	onenand;
+	struct onenand_flash	flash;
+};
+
+static struct onenand_info *info;
+
+#define DPRINTK(format, args...)					\
+do {									\
+	printk(KERN_DEBUG "%s[%d]: " format "\n", __func__,		\
+			   __LINE__, ##args);				\
+} while (0)
+
+/**
+ * onenand_lock_handle - Handle Lock scheme
+ * @this:		OneNAND device structure
+ * @cmd:		The command to be sent
+ *
+ * Send lock command to OneNAND device.
+ * The lock scheme depends on chip type.
+ */
+static void onenand_lock_handle(struct onenand_chip *this, int cmd)
+{
+	int block_lock_scheme;
+	int status;
+
+	status = ONENAND_GET_WP_STATUS(this);
+	block_lock_scheme = !(this->options & ONENAND_HAS_CONT_LOCK);
+
+	switch (cmd) {
+	case ONENAND_CMD_UNLOCK:
+	case ONENAND_CMD_UNLOCK_ALL:
+		if (block_lock_scheme)
+			ONENAND_SET_WP_STATUS(ONENAND_WP_US, this);
+		else
+			ONENAND_SET_WP_STATUS(status | ONENAND_WP_US, this);
+		break;
+
+	case ONENAND_CMD_LOCK:
+		if (block_lock_scheme)
+			ONENAND_SET_WP_STATUS(ONENAND_WP_LS, this);
+		else
+			ONENAND_SET_WP_STATUS(status | ONENAND_WP_LS, this);
+		break;
+
+	case ONENAND_CMD_LOCK_TIGHT:
+		if (block_lock_scheme)
+			ONENAND_SET_WP_STATUS(ONENAND_WP_LTS, this);
+		else
+			ONENAND_SET_WP_STATUS(status | ONENAND_WP_LTS, this);
+		break;
+
+	default:
+		break;
+	}
+}
+
+/**
+ * onenand_bootram_handle - Handle BootRAM area
+ * @this:		OneNAND device structure
+ * @cmd:		The command to be sent
+ *
+ * Emulate BootRAM area. It is possible to do basic operation using BootRAM.
+ */
+static void onenand_bootram_handle(struct onenand_chip *this, int cmd)
+{
+	switch (cmd) {
+	case ONENAND_CMD_READID:
+		writew(manuf_id, this->base);
+		writew(device_id, this->base + 2);
+		writew(version_id, this->base + 4);
+		break;
+
+	default:
+		/* REVIST: Handle other commands */
+		break;
+	}
+}
+
+/**
+ * onenand_update_interrupt - Set interrupt register
+ * @this:         OneNAND device structure
+ * @cmd:          The command to be sent
+ *
+ * Update interrupt register. The status depends on command.
+ */
+static void onenand_update_interrupt(struct onenand_chip *this, int cmd)
+{
+	int interrupt = ONENAND_INT_MASTER;
+
+	switch (cmd) {
+	case ONENAND_CMD_READ:
+	case ONENAND_CMD_READOOB:
+		interrupt |= ONENAND_INT_READ;
+		break;
+
+	case ONENAND_CMD_PROG:
+	case ONENAND_CMD_PROGOOB:
+		interrupt |= ONENAND_INT_WRITE;
+		break;
+
+	case ONENAND_CMD_ERASE:
+		interrupt |= ONENAND_INT_ERASE;
+		break;
+
+	case ONENAND_CMD_RESET:
+		interrupt |= ONENAND_INT_RESET;
+		break;
+
+	default:
+		break;
+	}
+
+	writew(interrupt, this->base + ONENAND_REG_INTERRUPT);
+}
+
+/**
+ * onenand_check_overwrite - Check if over-write happened
+ * @dest:		The destination pointer
+ * @src:		The source pointer
+ * @count:		The length to be check
+ *
+ * Returns:		0 on same, otherwise 1
+ *
+ * Compare the source with destination
+ */
+static int onenand_check_overwrite(void *dest, void *src, size_t count)
+{
+	unsigned int *s = (unsigned int *) src;
+	unsigned int *d = (unsigned int *) dest;
+	int i;
+
+	count >>= 2;
+	for (i = 0; i < count; i++)
+		if ((*s++ ^ *d++) != 0)
+			return 1;
+
+	return 0;
+}
+
+/**
+ * onenand_data_handle - Handle OneNAND Core and DataRAM
+ * @this:		OneNAND device structure
+ * @cmd:		The command to be sent
+ * @dataram:		Which dataram used
+ * @offset:		The offset to OneNAND Core
+ *
+ * Copy data from OneNAND Core to DataRAM (read)
+ * Copy data from DataRAM to OneNAND Core (write)
+ * Erase the OneNAND Core (erase)
+ */
+static void onenand_data_handle(struct onenand_chip *this, int cmd,
+				int dataram, unsigned int offset)
+{
+	struct mtd_info *mtd = &info->mtd;
+	struct onenand_flash *flash = this->priv;
+	int main_offset, spare_offset, die = 0;
+	void __iomem *src;
+	void __iomem *dest;
+	unsigned int i;
+	static int pi_operation;
+	int erasesize, rgn;
+
+	if (dataram) {
+		main_offset = mtd->writesize;
+		spare_offset = mtd->oobsize;
+	} else {
+		main_offset = 0;
+		spare_offset = 0;
+	}
+
+	if (pi_operation) {
+		die = readw(this->base + ONENAND_REG_START_ADDRESS2);
+		die >>= ONENAND_DDP_SHIFT;
+	}
+
+	switch (cmd) {
+	case FLEXONENAND_CMD_PI_ACCESS:
+		pi_operation = 1;
+		break;
+
+	case ONENAND_CMD_RESET:
+		pi_operation = 0;
+		break;
+
+	case ONENAND_CMD_READ:
+		src = ONENAND_CORE(flash) + offset;
+		dest = ONENAND_MAIN_AREA(this, main_offset);
+		if (pi_operation) {
+			writew(boundary[die], this->base + ONENAND_DATARAM);
+			break;
+		}
+		memcpy(dest, src, mtd->writesize);
+		/* Fall through */
+
+	case ONENAND_CMD_READOOB:
+		src = ONENAND_CORE_SPARE(flash, this, offset);
+		dest = ONENAND_SPARE_AREA(this, spare_offset);
+		memcpy(dest, src, mtd->oobsize);
+		break;
+
+	case ONENAND_CMD_PROG:
+		src = ONENAND_MAIN_AREA(this, main_offset);
+		dest = ONENAND_CORE(flash) + offset;
+		if (pi_operation) {
+			boundary[die] = readw(this->base + ONENAND_DATARAM);
+			break;
+		}
+		/* To handle partial write */
+		for (i = 0; i < (1 << mtd->subpage_sft); i++) {
+			int off = i * this->subpagesize;
+			if (!memcmp(src + off, ffchars, this->subpagesize))
+				continue;
+			if (memcmp(dest + off, ffchars, this->subpagesize) &&
+			    onenand_check_overwrite(dest + off, src + off, this->subpagesize))
+				printk(KERN_ERR "over-write happend at 0x%08x\n", offset);
+			memcpy(dest + off, src + off, this->subpagesize);
+		}
+		/* Fall through */
+
+	case ONENAND_CMD_PROGOOB:
+		src = ONENAND_SPARE_AREA(this, spare_offset);
+		/* Check all data is 0xff chars */
+		if (!memcmp(src, ffchars, mtd->oobsize))
+			break;
+
+		dest = ONENAND_CORE_SPARE(flash, this, offset);
+		if (memcmp(dest, ffchars, mtd->oobsize) &&
+		    onenand_check_overwrite(dest, src, mtd->oobsize))
+			printk(KERN_ERR "OOB: over-write happend at 0x%08x\n",
+			       offset);
+		memcpy(dest, src, mtd->oobsize);
+		break;
+
+	case ONENAND_CMD_ERASE:
+		if (pi_operation)
+			break;
+
+		if (FLEXONENAND(this)) {
+			rgn = flexonenand_region(mtd, offset);
+			erasesize = mtd->eraseregions[rgn].erasesize;
+		} else
+			erasesize = mtd->erasesize;
+
+		memset(ONENAND_CORE(flash) + offset, 0xff, erasesize);
+		memset(ONENAND_CORE_SPARE(flash, this, offset), 0xff,
+		       (erasesize >> 5));
+		break;
+
+	default:
+		break;
+	}
+}
+
+/**
+ * onenand_command_handle - Handle command
+ * @this:		OneNAND device structure
+ * @cmd:		The command to be sent
+ *
+ * Emulate OneNAND command.
+ */
+static void onenand_command_handle(struct onenand_chip *this, int cmd)
+{
+	unsigned long offset = 0;
+	int block = -1, page = -1, bufferram = -1;
+	int dataram = 0;
+
+	switch (cmd) {
+	case ONENAND_CMD_UNLOCK:
+	case ONENAND_CMD_LOCK:
+	case ONENAND_CMD_LOCK_TIGHT:
+	case ONENAND_CMD_UNLOCK_ALL:
+		onenand_lock_handle(this, cmd);
+		break;
+
+	case ONENAND_CMD_BUFFERRAM:
+		/* Do nothing */
+		return;
+
+	default:
+		block = (int) readw(this->base + ONENAND_REG_START_ADDRESS1);
+		if (block & (1 << ONENAND_DDP_SHIFT)) {
+			block &= ~(1 << ONENAND_DDP_SHIFT);
+			/* The half of chip block */
+			block += this->chipsize >> (this->erase_shift + 1);
+		}
+		if (cmd == ONENAND_CMD_ERASE)
+			break;
+
+		page = (int) readw(this->base + ONENAND_REG_START_ADDRESS8);
+		page = (page >> ONENAND_FPA_SHIFT);
+		bufferram = (int) readw(this->base + ONENAND_REG_START_BUFFER);
+		bufferram >>= ONENAND_BSA_SHIFT;
+		bufferram &= ONENAND_BSA_DATARAM1;
+		dataram = (bufferram == ONENAND_BSA_DATARAM1) ? 1 : 0;
+		break;
+	}
+
+	if (block != -1)
+		offset = onenand_addr(this, block);
+
+	if (page != -1)
+		offset += page << this->page_shift;
+
+	onenand_data_handle(this, cmd, dataram, offset);
+
+	onenand_update_interrupt(this, cmd);
+}
+
+/**
+ * onenand_writew - [OneNAND Interface] Emulate write operation
+ * @value:		value to write
+ * @addr:		address to write
+ *
+ * Write OneNAND register with value
+ */
+static void onenand_writew(unsigned short value, void __iomem * addr)
+{
+	struct onenand_chip *this = info->mtd.priv;
+
+	/* BootRAM handling */
+	if (addr < this->base + ONENAND_DATARAM) {
+		onenand_bootram_handle(this, value);
+		return;
+	}
+	/* Command handling */
+	if (addr == this->base + ONENAND_REG_COMMAND)
+		onenand_command_handle(this, value);
+
+	writew(value, addr);
+}
+
+/**
+ * flash_init - Initialize OneNAND simulator
+ * @flash:		OneNAND simulator data strucutres
+ *
+ * Initialize OneNAND simulator.
+ */
+static int __init flash_init(struct onenand_flash *flash)
+{
+	int density, size;
+	int buffer_size;
+
+	flash->base = kzalloc(131072, GFP_KERNEL);
+	if (!flash->base) {
+		printk(KERN_ERR "Unable to allocate base address.\n");
+		return -ENOMEM;
+	}
+
+	density = device_id >> ONENAND_DEVICE_DENSITY_SHIFT;
+	density &= ONENAND_DEVICE_DENSITY_MASK;
+	size = ((16 << 20) << density);
+
+	ONENAND_CORE(flash) = vmalloc(size + (size >> 5));
+	if (!ONENAND_CORE(flash)) {
+		printk(KERN_ERR "Unable to allocate nand core address.\n");
+		kfree(flash->base);
+		return -ENOMEM;
+	}
+
+	memset(ONENAND_CORE(flash), 0xff, size + (size >> 5));
+
+	/* Setup registers */
+	writew(manuf_id, flash->base + ONENAND_REG_MANUFACTURER_ID);
+	writew(device_id, flash->base + ONENAND_REG_DEVICE_ID);
+	writew(version_id, flash->base + ONENAND_REG_VERSION_ID);
+	writew(technology_id, flash->base + ONENAND_REG_TECHNOLOGY);
+
+	if (density < 2 && (!CONFIG_FLEXONENAND))
+		buffer_size = 0x0400;	/* 1KiB page */
+	else
+		buffer_size = 0x0800;	/* 2KiB page */
+	writew(buffer_size, flash->base + ONENAND_REG_DATA_BUFFER_SIZE);
+
+	return 0;
+}
+
+/**
+ * flash_exit - Clean up OneNAND simulator
+ * @flash:		OneNAND simulator data structures
+ *
+ * Clean up OneNAND simulator.
+ */
+static void flash_exit(struct onenand_flash *flash)
+{
+	vfree(ONENAND_CORE(flash));
+	kfree(flash->base);
+}
+
+static int __init onenand_sim_init(void)
+{
+	/* Allocate all 0xff chars pointer */
+	ffchars = kmalloc(MAX_ONENAND_PAGESIZE, GFP_KERNEL);
+	if (!ffchars) {
+		printk(KERN_ERR "Unable to allocate ff chars.\n");
+		return -ENOMEM;
+	}
+	memset(ffchars, 0xff, MAX_ONENAND_PAGESIZE);
+
+	/* Allocate OneNAND simulator mtd pointer */
+	info = kzalloc(sizeof(struct onenand_info), GFP_KERNEL);
+	if (!info) {
+		printk(KERN_ERR "Unable to allocate core structures.\n");
+		kfree(ffchars);
+		return -ENOMEM;
+	}
+
+	/* Override write_word function */
+	info->onenand.write_word = onenand_writew;
+
+	if (flash_init(&info->flash)) {
+		printk(KERN_ERR "Unable to allocate flash.\n");
+		kfree(ffchars);
+		kfree(info);
+		return -ENOMEM;
+	}
+
+	info->parts = os_partitions;
+
+	info->onenand.base = info->flash.base;
+	info->onenand.priv = &info->flash;
+
+	info->mtd.name = "OneNAND simulator";
+	info->mtd.priv = &info->onenand;
+	info->mtd.owner = THIS_MODULE;
+
+	if (onenand_scan(&info->mtd, 1)) {
+		flash_exit(&info->flash);
+		kfree(ffchars);
+		kfree(info);
+		return -ENXIO;
+	}
+
+	add_mtd_partitions(&info->mtd, info->parts, ARRAY_SIZE(os_partitions));
+
+	return 0;
+}
+
+static void __exit onenand_sim_exit(void)
+{
+	struct onenand_chip *this = info->mtd.priv;
+	struct onenand_flash *flash = this->priv;
+
+	onenand_release(&info->mtd);
+	flash_exit(flash);
+	kfree(ffchars);
+	kfree(info);
+}
+
+module_init(onenand_sim_init);
+module_exit(onenand_sim_exit);
+
+MODULE_AUTHOR("Kyungmin Park <kyungmin.park@samsung.com>");
+MODULE_DESCRIPTION("The OneNAND flash simulator");
+MODULE_LICENSE("GPL");