71 lines
3.2 KiB
Plaintext
71 lines
3.2 KiB
Plaintext
* UCC (Unified Communications Controllers)
|
|
|
|
Required properties:
|
|
- device_type : should be "network", "hldc", "uart", "transparent"
|
|
"bisync", "atm", or "serial".
|
|
- compatible : could be "ucc_geth" or "fsl_atm" and so on.
|
|
- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
|
|
- reg : Offset and length of the register set for the device
|
|
- interrupts : <a b> where a is the interrupt number and b is a
|
|
field that represents an encoding of the sense and level
|
|
information for the interrupt. This should be encoded based on
|
|
the information in section 2) depending on the type of interrupt
|
|
controller you have.
|
|
- interrupt-parent : the phandle for the interrupt controller that
|
|
services interrupts for this device.
|
|
- pio-handle : The phandle for the Parallel I/O port configuration.
|
|
- port-number : for UART drivers, the port number to use, between 0 and 3.
|
|
This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
|
|
The port number is added to the minor number of the device. Unlike the
|
|
CPM UART driver, the port-number is required for the QE UART driver.
|
|
- soft-uart : for UART drivers, if specified this means the QE UART device
|
|
driver should use "Soft-UART" mode, which is needed on some SOCs that have
|
|
broken UART hardware. Soft-UART is provided via a microcode upload.
|
|
- rx-clock-name: the UCC receive clock source
|
|
"none": clock source is disabled
|
|
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
|
|
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
|
|
- tx-clock-name: the UCC transmit clock source
|
|
"none": clock source is disabled
|
|
"brg1" through "brg16": clock source is BRG1-BRG16, respectively
|
|
"clk1" through "clk24": clock source is CLK1-CLK24, respectively
|
|
The following two properties are deprecated. rx-clock has been replaced
|
|
with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
|
|
Drivers that currently use the deprecated properties should continue to
|
|
do so, in order to support older device trees, but they should be updated
|
|
to check for the new properties first.
|
|
- rx-clock : represents the UCC receive clock source.
|
|
0x00 : clock source is disabled;
|
|
0x1~0x10 : clock source is BRG1~BRG16 respectively;
|
|
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
|
|
- tx-clock: represents the UCC transmit clock source;
|
|
0x00 : clock source is disabled;
|
|
0x1~0x10 : clock source is BRG1~BRG16 respectively;
|
|
0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
|
|
|
|
Required properties for network device_type:
|
|
- mac-address : list of bytes representing the ethernet address.
|
|
- phy-handle : The phandle for the PHY connected to this controller.
|
|
|
|
Recommended properties:
|
|
- phy-connection-type : a string naming the controller/PHY interface type,
|
|
i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
|
|
Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
|
|
"tbi", or "rtbi".
|
|
|
|
Example:
|
|
ucc@2000 {
|
|
device_type = "network";
|
|
compatible = "ucc_geth";
|
|
cell-index = <1>;
|
|
reg = <2000 200>;
|
|
interrupts = <a0 0>;
|
|
interrupt-parent = <700>;
|
|
mac-address = [ 00 04 9f 00 23 23 ];
|
|
rx-clock = "none";
|
|
tx-clock = "clk9";
|
|
phy-handle = <212000>;
|
|
phy-connection-type = "gmii";
|
|
pio-handle = <140001>;
|
|
};
|