satip-axe/kernel/arch/mips/alchemy/devboards/pb1000/board_setup.c
2015-03-26 17:24:57 +01:00

196 lines
5.6 KiB
C

/*
* Copyright 2000, 2008 MontaVista Software Inc.
* Author: MontaVista Software, Inc. <source@mvista.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1000.h>
#include <prom.h>
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1000_GPIO_15, IRQF_TRIGGER_LOW, 0 },
};
const char *get_system_type(void)
{
return "Alchemy Pb1000";
}
void board_reset(void)
{
}
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
void __init board_setup(void)
{
u32 pin_func, static_cfg0;
u32 sys_freqctrl, sys_clksrc;
u32 prid = read_c0_prid();
#ifdef CONFIG_SERIAL_8250_CONSOLE
char *argptr = prom_getcmdline();
argptr = strstr(argptr, "console=");
if (argptr == NULL) {
argptr = prom_getcmdline();
strcat(argptr, " console=ttyS0,115200");
}
#endif
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PINSTATERD);
udelay(100);
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* Zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* Zero and disable USBH/USBD clocks */
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
au_writel(sys_clksrc, SYS_CLKSRC);
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
switch (prid & 0x000000FF) {
case 0x00: /* DA */
case 0x01: /* HA */
case 0x02: /* HB */
/* CPU core freq to 48 MHz to slow it way down... */
au_writel(4, SYS_CPUPLL);
/*
* Setup 48 MHz FREQ2 from CPUPLL for USB Host
* FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
*/
sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* CPU core freq to 384 MHz */
au_writel(0x20, SYS_CPUPLL);
printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
break;
default: /* HC and newer */
/* FREQ2 = aux / 2 = 48 MHz */
sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
SYS_FC_FE2 | SYS_FC_FS2;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
break;
}
/*
* Route 48 MHz FREQ2 into USB Host and/or Device
*/
sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
au_writel(sys_clksrc, SYS_CLKSRC);
/* Configure pins GPIO[14:9] as GPIO */
pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
/* 2nd USB port is USB host */
pin_func |= SYS_PF_USB;
au_writel(pin_func, SYS_PINFUNC);
alchemy_gpio_direction_input(11);
alchemy_gpio_direction_input(13);
alchemy_gpio_direction_output(4, 0);
alchemy_gpio_direction_output(5, 0);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
/* Make GPIO 15 an input (for interrupt line) */
pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
/* We don't need I2S, so make it available for GPIO[31:29] */
pin_func |= SYS_PF_I2S;
au_writel(pin_func, SYS_PINFUNC);
alchemy_gpio_direction_input(15);
static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
au_writel(static_cfg0, MEM_STCFG0);
/* configure RCE2* for LCD */
au_writel(0x00000004, MEM_STCFG2);
/* MEM_STTIME2 */
au_writel(0x09000000, MEM_STTIME2);
/* Set 32-bit base address decoding for RCE2* */
au_writel(0x10003ff0, MEM_STADDR2);
/*
* PCI CPLD setup
* Expand CE0 to cover PCI
*/
au_writel(0x11803e40, MEM_STADDR1);
/* Burst visibility on */
au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */
au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */
/* Setup the static bus controller */
au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
/*
* Enable Au1000 BCLK switching - note: sed1356 must not use
* its BCLK (Au1000 LCLK) for any timings
*/
switch (prid & 0x000000FF) {
case 0x00: /* DA */
case 0x01: /* HA */
case 0x02: /* HB */
break;
default: /* HC and newer */
/*
* Enable sys bus clock divider when IDLE state or no bus
* activity.
*/
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
break;
}
}