satip-axe/kernel/arch/mips/alchemy/devboards/pb1500/board_setup.c
2015-03-26 17:24:57 +01:00

166 lines
5.1 KiB
C

/*
* Copyright 2000, 2008 MontaVista Software Inc.
* Author: MontaVista Software, Inc. <source@mvista.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1500.h>
#include <prom.h>
char irq_tab_alchemy[][5] __initdata = {
[12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
[13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
};
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
{ AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
{ AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
};
const char *get_system_type(void)
{
return "Alchemy Pb1500";
}
void board_reset(void)
{
/* Hit BCSR.RST_VDDI[SOFT_RESET] */
au_writel(0x00000000, PB1500_RST_VDDI);
}
void __init board_init_irq(void)
{
au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
}
void __init board_setup(void)
{
u32 pin_func;
u32 sys_freqctrl, sys_clksrc;
char *argptr;
argptr = prom_getcmdline();
#ifdef CONFIG_SERIAL_8250_CONSOLE
argptr = strstr(argptr, "console=");
if (argptr == NULL) {
argptr = prom_getcmdline();
strcat(argptr, " console=ttyS0,115200");
}
#endif
#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
/* au1000 does not support vra, au1500 and au1100 do */
strcat(argptr, " au1000_audio=vra");
argptr = prom_getcmdline();
#endif
sys_clksrc = sys_freqctrl = pin_func = 0;
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PINSTATERD);
udelay(100);
/* GPIO201 is input for PCMCIA card detect */
/* GPIO203 is input for PCMCIA interrupt request */
alchemy_gpio_direction_input(201);
alchemy_gpio_direction_input(203);
#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
/* Zero and disable FREQ2 */
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/* zero and disable USBH/USBD clocks */
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
au_writel(sys_clksrc, SYS_CLKSRC);
sys_freqctrl = au_readl(SYS_FREQCTRL0);
sys_freqctrl &= ~0xFFF00000;
sys_clksrc = au_readl(SYS_CLKSRC);
sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
/* FREQ2 = aux/2 = 48 MHz */
sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
au_writel(sys_freqctrl, SYS_FREQCTRL0);
/*
* Route 48MHz FREQ2 into USB Host and/or Device
*/
sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
au_writel(sys_clksrc, SYS_CLKSRC);
pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
/* 2nd USB port is USB host */
pin_func |= SYS_PF_USB;
au_writel(pin_func, SYS_PINFUNC);
#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
#ifdef CONFIG_PCI
/* Setup PCI bus controller */
au_writel(0, Au1500_PCI_CMEM);
au_writel(0x00003fff, Au1500_CFG_BASE);
#if defined(__MIPSEB__)
au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
#else
au_writel(0xf, Au1500_PCI_CFG);
#endif
au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
au_writel(0x02a00356, Au1500_PCI_STATCMD);
au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
au_writel(0x00000008, Au1500_PCI_MBAR);
au_sync();
#endif
/* Enable sys bus clock divider when IDLE state or no bus activity. */
au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
/* Enable the RTC if not already enabled */
if (!(au_readl(0xac000028) & 0x20)) {
printk(KERN_INFO "enabling clock ...\n");
au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
}
/* Put the clock in BCD mode */
if (au_readl(0xac00002c) & 0x4) { /* reg B */
au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
au_sync();
}
}