275 lines
11 KiB
Plaintext
275 lines
11 KiB
Plaintext
SATIP-AXE firmware binary files
|
|
===============================
|
|
|
|
This directory contains USB and flash firmware for
|
|
* Inverto IDL-400s
|
|
* Grundig GSS.BOX
|
|
* Telestar Digibit R1
|
|
|
|
Update:
|
|
-------
|
|
|
|
- check differences in /etc/config.default against /etc/sysconfig/config
|
|
- example: diff -u /etc/config.default /etc/sysconfig/config
|
|
- since build 9 firmware upgrade may be upgraded using upgrade-fw tool
|
|
- file can be fetched directly from github
|
|
- or specified as a local firmware file directly
|
|
- the file is copied to ramfs before flashing
|
|
- the first attempt fails usually (ask Inverto), press Enter to repeat
|
|
- example: 'upgrade-fw'
|
|
- lists firmwares on github
|
|
- example: 'upgrade-fw satip-axe-201504211434-8.fw'
|
|
- fetches file from github and flashes it, but if the local
|
|
file satip-axe-201504211434-8.fw exists, it is preferred
|
|
|
|
Installation:
|
|
-------------
|
|
|
|
- set DHCP in the original firmware (not 100% required, but several
|
|
users reported that without this change the network might not work)
|
|
- setup a DHCP server for the box ethernet MAC address
|
|
- copy satip-axe-$(VERSION).usb as idl4k.scr (rename the file) to the USB stick
|
|
- copy satip-axe-$(VERSION).fw (no rename) to the USB stick
|
|
- both files should be in the root directory on the USB stick
|
|
- plug the USB stick to the upper USB port in box
|
|
- turn on the box
|
|
- the tuner LEDs must blink (Knight Rider effect) for few seconds
|
|
- box is accessible through telnet or ssh, IP address is obtained using DHCP
|
|
- the default login/password is root/satip
|
|
- the firmware is not written to the internal flash - when the USB stick
|
|
is not in the box, the original firmware will be booted
|
|
|
|
Installation to internal flash:
|
|
-------------------------------
|
|
|
|
- WARNING! The original firmware will be deactivated!
|
|
- the original firmware can be turned on using idl4k.recovery (see bellow)
|
|
- same steps, but use satip-axe-$(VERSION).flash file as idl4k.scr
|
|
- after boot of the new version, remove the USB stick to not write
|
|
the .fw file multiple times to flash (on each box start); eventually
|
|
the idl4k.scr file can be removed from the USB stick to prevent
|
|
another reflash
|
|
- the firmware is written to another internal flash area than
|
|
the original firmware, but uboot is reconfigured
|
|
|
|
Customization:
|
|
--------------
|
|
|
|
- configuration file is in /etc/sysconfig/config
|
|
- put localtime file (glibc) to /etc/sysconfig/localtime
|
|
- put resolv.conf file to /etc/sysconfig/resolv.conf
|
|
- localboot script can be in /etc/sysconfig/localboot
|
|
- passwd file is copied from /etc/sysconfig/passwd
|
|
- ssh authorized_keys file is copied from /etc/sysconfig/authorized_keys
|
|
- inetd.conf file is linked to /etc/sysconfig/inetd.conf
|
|
- oscam configs are in /etc/sysconfig/oscam directory
|
|
- if /etc/sysconfig/customd script exists, it is executed from init
|
|
- if /etc/sysconfig/profile script exists, it is executed at login
|
|
- writeable ftp - copy /etc/inetd.conf to /etc/sysconfig/inetd.conf and
|
|
add -w argument to the ftpd daemon
|
|
|
|
httpd:
|
|
------
|
|
|
|
- /media tree is exported
|
|
|
|
ftpd:
|
|
-----
|
|
|
|
- /media tree is exported, use root/satip as login
|
|
|
|
nfsd:
|
|
-----
|
|
|
|
- only v3 protocol is supported
|
|
- to list connected clients 'showmount'
|
|
- to list exports 'exportfs'
|
|
|
|
Minisatip config:
|
|
-----------------
|
|
|
|
- you may add extra parameters to MINISATIP_OPTS= in /etc/sysconfig/config
|
|
- WARNING: use -d with unique numbers if you have _multiple_ SAT>IP servers on net
|
|
- SEE: minisatip.md file in this directory for more details
|
|
- example 1: only two tuners: MINISATIP_OPTS="-e 0-1"
|
|
- example 2: unicable: MINISATIP_OPTS="-u 0:1-1420,1:0-1210,2:2-1680,3:3-2040"
|
|
- AXE hardware specific options:
|
|
-L link adapters (identical src,lo/hi,h/v), the format is M:S (master:slave)
|
|
-Q quattro LNB config (H/H,H/V,L/H,L/V)
|
|
-X X AXE unicable/jess input (0-3)
|
|
- example 3: unicable coax in input 2: MINISATIP_OPTS="-X 1"
|
|
- example 4: quattro LNB: MINISATIP_OPTS="-Q"
|
|
- example 5: coax in inputs 1,2, tuner 3 slave to input 1, tuner 4 slave to input 2
|
|
MINISATIP_OPTS="-L 0:2,1:3"
|
|
|
|
OSCAM config:
|
|
-------------
|
|
|
|
- in /etc/sysconfig/oscam directory
|
|
- login/password is oscam/satip, http webui available at http://<boxip>:8888
|
|
- use persistent serial device names (like /dev/ttyUSB1-1.2:1.0)
|
|
- or use customized serial device names (see /etc/sysconfig/config)
|
|
|
|
Misc:
|
|
-----
|
|
|
|
- full tuner reset - "axe-debug reset"
|
|
|
|
Recovery from the wrong configuration:
|
|
--------------------------------------
|
|
|
|
- it works with firmware build 10 and later
|
|
- for flashed firmware:
|
|
- copy idl4k.cfgreset file as idl4k.scr file to the root directory on the USB stick
|
|
- for firmware on the USB stick:
|
|
- copy idl4k.cfgresetusb file as idl4k.scr file to the root directory on the USB stick
|
|
- copy satip-axe-*.fw file as satip-axe.fw to the root directory on the USB stick
|
|
(build 10 or later)
|
|
- plug the USB stick to the upper USB port in box
|
|
- turn on the box
|
|
- the old configuration file is moved to /etc/sysconfig/config.old
|
|
|
|
Recovery of the original firmware:
|
|
----------------------------------
|
|
|
|
- copy idl4k.recovery file as idl4k.scr file to the root directory on the USB stick
|
|
- plug the USB stick to the upper USB port in box
|
|
- turn on the box
|
|
- box is accessible through http (web browser) - original firmware
|
|
|
|
Notes:
|
|
------
|
|
|
|
- there is 128M SPI flash memory in the device
|
|
- 128k for u-boot (probably)
|
|
- 4M marked as system-nand0 (probably unused)
|
|
- the original firmware uses fw1-nand0 flash region (32M)
|
|
- the satip-axe firmware uses fw2-nand0 flash region (32M)
|
|
- data block is named data-nand0 - uses rest of flash
|
|
|
|
Disclaimer:
|
|
-----------
|
|
|
|
The SATIP AXE firmware is supplied "AS IS" without any warranties and
|
|
support.
|
|
|
|
The authors assumes no responsibility or liability for the use of
|
|
the software, conveys no license or title under any patent, copyright, or
|
|
mask work right to the product.
|
|
|
|
The authors reserve the right to make changes in the software
|
|
without notification. Authors also make no representation or
|
|
warranty that such software will be suitable for the specified use
|
|
without further testing or modification.
|
|
|
|
Bugs:
|
|
-----
|
|
|
|
- the Inverto driver do not initialize properly sometimes
|
|
(minisatip is not started); if minisatip does not work,
|
|
you may check 'logread' for tuner initialization error (512)
|
|
or use 'dmesg' to check the lines bellow;
|
|
turn off the box for 5-30 minutes and try again...
|
|
|
|
demod900] setup [num_demods 4]
|
|
[pll6120] setup [num_plls:4] [clk:30000000] [bbgain:16]
|
|
[fe] Checking lut 0xC1ABEAF0
|
|
[fe] Checking lut 0xC1ABEB26
|
|
[fe] Checking lut 0xC1ABEAF0
|
|
[fe] Checking lut 0xC1ABEB54
|
|
[dmx] ... init 0
|
|
[dmx-ts] ... init 0
|
|
[i2c] I2C bus error /errno -121/!!
|
|
[i2c] I2C bus error /errno -121/!!
|
|
[i2c] I2C bus error /errno -121/!!
|
|
[pll6120] init error!
|
|
[fta_fe] FE Initialization done, res -1
|
|
|
|
- reboot command cannot be used (uboot usb init fails, hw init fails)
|
|
|
|
History:
|
|
--------
|
|
|
|
upcoming - https://github.com/perexg/satip-axe/issues/45
|
|
- updated stmmac ethernet driver from latest stlinux kernel
|
|
- linux-sh4-2.6.32.y - _stm24_0217
|
|
- enabled Realtek PHY module (RTL8211E)
|
|
- disable scatter-gather, increase ring descriptors (from 256 to 512)
|
|
- updated dropbear to 2015.71
|
|
- changed from dss host key to rsa host key (for latest openssl)
|
|
- updated nfsutils to 1.3.3
|
|
- updated nano to 2.4.3
|
|
- updated oscam to 11211
|
|
- updated axe_dmxts.ko kernel module from idl4k-1.24.0.156
|
|
- minisatip accepts -M option to skip first MPEG-TS packets from demuxer
|
|
- the default value is 35 (to skip packets from previous tune)
|
|
- minisatip can handle multiple unicable groups (-U t1,t2,t3,t4 option)
|
|
- added second minisatip binary (minisatip5 - based on 0.5.26 version)
|
|
- add new lines to /etc/sysconfig/config from /etc/config.default
|
|
|
|
satip-axe-201508061051-10 - Thu Aug 6 2015
|
|
- replaced stapi / frontend / demuxer drivers with latest from Inverto
|
|
- updated kernel USB stack, fixed ftdi_sio kernel oops (mouse readers)
|
|
- updated minisatip to new demuxts (reduce CPU usage)
|
|
- fixed -b option for minisatip
|
|
- updated oscamd to 10937
|
|
- fixed /etc/mdev.conf to mount USB sticks without partitions
|
|
- added idl4k.cfgreset script to reset wrong config
|
|
|
|
satip-axe-201505242057-9 - Sun May 24 2015
|
|
- added http://boxip:8080/axe-status.txt status page (shell parseable)
|
|
- fixed ntpd start
|
|
- added crond start / configuration
|
|
- added customd start (custom daemon/service/setup - script) from init
|
|
- added nano text editor
|
|
- updated oscam to 10663
|
|
- added upgrade-fw script for the internal flash upgrade without an USB stick
|
|
- added /etc/sysconfig/profile support
|
|
|
|
satip-axe-201504211434-8 - Tue Apr 21 2015
|
|
- faster boot (approx. 25 seconds from flash)
|
|
- tuners - configurable gain (0-16dB) - STV6210_BAMP in config
|
|
- enabled inetd/httpd/ftpd/nfsd by default
|
|
- added nfsd v3 support
|
|
- added ethtool
|
|
- extended debug tools for I2C bus (axe-debug, axehelper)
|
|
|
|
satip-axe-201504142137-7 - Tue Apr 14 2015
|
|
- minisatip
|
|
- allow configurable DVR read buffer (-b option)
|
|
- decrease default DVR read buffer to 14 UDP packets (18424 bytes)
|
|
- allow 13V only for unicable/jess (* before freq)
|
|
- tuner LED fixes
|
|
- AXE modules
|
|
- remove the load hell from STLinux, move everything to /etc/init.d/rcS
|
|
- another workarounds for the correct tuner initialization
|
|
|
|
satip-axe-201504101512-6 - Fri Apr 10 2015
|
|
- extended minisatip (quattro LNB, master/slave, unicable on other input)
|
|
- another shuffling in the AXE modules load procedure
|
|
|
|
satip-axe-201504092035-5 - Thu Apr 9 2015
|
|
- fixed minisatip & dhcp issue - minisatip is started with good IP
|
|
- changed load order of AXE modules and AXE hw initialization
|
|
|
|
satip-axe-201504082030-4 : Wed Apr 8 2015
|
|
- upgraded busybox to v1.23.2
|
|
- added ntpd configuration (network time daemon)
|
|
- changed dropbear default PATH to "/sbin:/usr/sbin:/bin:/usr/bin:/usr/local/bin"
|
|
- added /dev/sd* devices hotplug (mounted to /media tree using labels)
|
|
- added kernel modules for USB serial converters (most Phoenix readers)
|
|
- added /dev/ttyUSB* devices hotplug (persistent names like /dev/ttyUSB2-1:1.0)
|
|
- added oscam r10619
|
|
- allow customization of hostname (/etc/sysconfig/config)
|
|
- minisatip fixes (signal levels, cleanups)
|
|
|
|
satip-axe-201504061852-3 : Mon Apr 6 2015
|
|
- minisatip fixes (unicable-jess, corrected input selection - coax inputs)
|
|
|
|
satip-axe-201504061852-2 : Mon Apr 6 2015
|
|
- minisatip fixes (unicable, multiple tuners, h/v and lo/hi setup)
|
|
- load axe modules in rcSBB
|
|
|
|
satip-axe-201503311856-1 : Tue Mar 31 2015
|
|
- initial firmware release
|