mirror of
https://github.com/VDR4Arch/vdr.git
synced 2023-10-10 13:36:52 +02:00
95 lines
4.2 KiB
Plaintext
95 lines
4.2 KiB
Plaintext
Installation of the Video Disk Recorder
|
|
---------------------------------------
|
|
|
|
Compiling and running the program:
|
|
----------------------------------
|
|
|
|
Make sure the files from this package are located in a
|
|
directory that is "parallel" to the DVB directory of the
|
|
driver source for the Siemens DVB-S PCI card (refer to
|
|
http://linuxtv.org/dvb/siemens_dvb.html for more information
|
|
about that driver). For example, if the DVB driver was
|
|
extracted into the directory /home/kls/vdr/DVB, then this
|
|
package should be extracted into /home/kls/vdr/VDR.
|
|
|
|
This program requires the card driver version 0.05 or higher
|
|
to work properly.
|
|
|
|
After extracting the package, change into the VDR directory
|
|
and type 'make'. This should produce an executable file
|
|
named 'vdr', which can be run after the DVB driver has been
|
|
installed.
|
|
|
|
There are two macros you can use to customize the 'vdr' program
|
|
at compile time. Adding "DEBUG_REMOTE=1" to the 'make' call
|
|
will use the PC's keyboard as input device instead of the "Remote
|
|
Control Unit" (see http://www.cadsoft.de/people/kls/vdr/remote.htm).
|
|
Adding "DEBUG_OSD=1" will use the PC screen (or current window)
|
|
to display texts instead of the DVB card's on-screen display
|
|
interface. These modes are useful when testing new menus if you
|
|
only have a remote connection to the VDR (which, in my case, is
|
|
located in the living room and has neither a monitor nor a keyboard).
|
|
|
|
When running, the 'vdr' program writes status information into the
|
|
system log file (/var/log/messages). You may want to watch these
|
|
messages (tail -f /var/log/mesages) to see if there are any problems.
|
|
|
|
The video data directory:
|
|
-------------------------
|
|
|
|
All recordings are written into directories below "/video". Please
|
|
make sure this directory exists, and that the user who runs the 'vdr'
|
|
program has read and write access to that directory.
|
|
If you prefer a different location for your video files, you can change
|
|
the value of 'BaseDir' in recording.c.
|
|
|
|
Note that the file system need not be 64-bit proof, since the 'vdr'
|
|
program splits video files into chunks of about 1GB. You should use
|
|
a disk with several gigabytes of free space. One GB can store roughly
|
|
half an hour of video data.
|
|
|
|
Configuration files:
|
|
--------------------
|
|
|
|
There are three configuration files that hold information about
|
|
channels, remote control keys and timers. These files are currrently
|
|
assumed to be located in the directory from which the 'vdr' program
|
|
was started (this will become configurable later). The configuration
|
|
files can be edited with any text editor, or will be written by the
|
|
'vdr' program if any changes are made inside the on-screen menus.
|
|
The meaning of the data entries may still vary in future releases,
|
|
so for the moment please look at the source code (config.c) to see
|
|
the meaning of the various fields.
|
|
|
|
Learning the remote control keys:
|
|
---------------------------------
|
|
|
|
There is no default 'keys.conf' file, so if you compile the program
|
|
without 'DEBUG_REMOTE=1' you will have to go through a "teach-in"
|
|
session that allows the program to learn your remote control codes.
|
|
It will first attempt to determine the basic data transfer mode and
|
|
timing of your remote control unit, and then will ask you to press one
|
|
key after the other so that it can learn the various key codes. You will
|
|
at least need to provide an "Up" and a "Down" key, so that you can switch
|
|
channels. The rest of the key definitions is optional, but the more keys
|
|
you define, the more you will be able to navigate through the menus and
|
|
control recording/replaying. The program uses only a very small number
|
|
of keys which have multiple meanings in the various modes (see MANUAL
|
|
for a detailed description).
|
|
If the program has been built with "DEBUG_REMOTE=1", it will use the
|
|
key configuration file 'keys-pc.conf', so that you won't loose data
|
|
when switching between normal and debug mode.
|
|
|
|
The default PC key assignments are:
|
|
|
|
Up, Down, Left, Right Crsr keys in numeric block
|
|
Menu 'Home' in numeric block
|
|
Ok '5' in numeric block
|
|
Back 'End' in numeric block
|
|
Red, Green, Yellow, Blue 'F1'..'F4'
|
|
0..9 '0'..'9' in top row
|
|
|
|
If you prefer different key assignments, simply delete the file
|
|
'keys-pc.conf' and restart 'vdr' to get into learning mode.
|
|
|