frodovdr/hyperion.ng
1
0
Fork 0
mirror of https://github.com/hyperion-project/hyperion.ng.git synced 2023-10-10 13:36:59 +02:00
Code Issues Releases Wiki Activity

optimize adalight firmware (#308)

Browse Source
This commit is contained in:
redPanther 2016-12-04 14:28:38 +01:00 committed by GitHub
parent 5b0e401ca5
commit 3124bb8bf1
1 changed files with 12 additions and 14 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

26
assets/firmware/arduino/adalight/adalight.ino
View File

@ -9,12 +9,11 @@
set following values to your needs
**************************************/
// Number of leds in your strip. set to 1 and ANALOG_OUTPUT_ENABLED to true to activate analog only
// Number of leds in your strip. set to "1" and ANALOG_OUTPUT_ENABLED to "true" to activate analog only
#define NUM_LEDS 100
#define SPI_LEDS false // connection type. Set "true" for 4 wire and "false" for 3 Wire stripes.
#define LED_TYPE WS2812B // type of your led controller, possible values, see below
// type of your led controller, possible values, see below
#define LED_TYPE WS2812B
// 3 wire (pwm): NEOPIXEL BTM1829 TM1812 TM1809 TM1804 TM1803 UCS1903 UCS1903B UCS1904 UCS2903 WS2812 WS2852
// S2812B SK6812 SK6822 APA106 PL9823 WS2811 WS2813 APA104 WS2811_40 GW6205 GW6205_40 LPD1886 LPD1886_8BIT
@ -22,8 +21,10 @@
// For 3 wire led stripes line Neopixel/Ws2812, which have a data line, ground, and power, you just need to define DATA_PIN.
// For led chipsets that are SPI based (four wires - data, clock, ground, and power), both defines DATA_PIN and CLOCK_PIN are needed
#define DATA_PIN 6
#define CLOCK_PIN 13
// DATA_PIN, or DATA_PIN, CLOCK_PIN
#define LED_PINS 6 // 3 wire leds
//#define LED_PINS 6, 13 // 4 wire leds
#define COLOR_ORDER GRB // colororder of the stripe, set RGB in hyperion
@ -33,7 +34,7 @@
// ATTENTION this pin config is default for atmega328 based arduinos, others might work to
// if you have flickering analog leds this might be caused by unsynced pwm signals
// try other pins is more or less the only thing that helps
#define ANALOG_OUTPUT_ENABLED true
#define ANALOG_OUTPUT_ENABLED false
#define ANALOG_MODE ANALOG_MODE_LAST_LED // use ANALOG_MODE_AVERAGE or ANALOG_MODE_LAST_LED
#define ANALOG_GROUND_PIN 8 // additional ground pin to make wiring a bit easier
#define ANALOG_RED_PIN 9
@ -48,7 +49,8 @@
#define BRIGHTNESS 255 // maximum brightness 0-255
#define DITHER_MODE BINARY_DITHER // BINARY_DITHER or DISABLE_DITHER
#define COLOR_TEMPERATURE CRGB(255,255,255) // RGB value describing the color temperature
#define COLOR_CORRECTION CRGB(255,255,255) // RGB value describing the color correction
#define COLOR_CORRECTION TypicalLEDStrip // predefined fastled color correction
//#define COLOR_CORRECTION CRGB(255,255,255) // or RGB value describing the color correction
// Baudrate, higher rate allows faster refresh rate and more LEDs (defined in /etc/boblight.conf)
#define serialRate 460800 // use 115200 for ftdi based boards
@ -133,13 +135,9 @@ void setup() {
}
#if NUM_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
#if SPI_LEDS == true
FastLED.addLeds<LED_TYPE, DATA_PIN, CLOCK_PIN, COLOR_ORDER>(leds, ledCount);
#else
FastLED.addLeds<LED_TYPE, DATA_PIN, COLOR_ORDER>(leds, ledCount);
#endif
FastLED.addLeds<LED_TYPE, LED_PINS, COLOR_ORDER>(leds, ledCount);
#endif
// color adjustments
FastLED.setBrightness ( BRIGHTNESS );
FastLED.setTemperature( COLOR_TEMPERATURE );