* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
* This add a new device type - ws2812spi.
I've (ab)used the SPI interface to send the correct timing pulses to keep the ws2812 happy.
THE RATE IS IMPORTANT!
A FIXED CORE_CLK IS IMPORTANT!
Attach the SPI MOSI pin on the Pi to the DIN pin on your ws2812
"device" :
{
"name" : "MyPi",
"type" : "ws2812spi",
"colorOrder" : "grb",
"output" : "/dev/spidev0.0",
"rate" : 3800000
},
* updated hyperiond.test-binary
* Updated default SPI speed to the "correct" value.
My Pi was undervolted so was dropping the core clock confusing everything
* Code cleanups
explicitly set the final 3 bytes to 0
* Removed latchtime option - not applicable
* updated test binary
Former-commit-id: d3c19c8374999f7a554bb25ca181a8a483f86289
* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
* started bug fixes for APA strips with more physical leds than configured
* 1st cut of changes to APA102.
now looks at config for "leds" which is the # of hardware leds in the strip.
This enables us to write the correct trailer length in the packet.
Also fixed a bug where switchoff was writing the wrong # of leds
* removed commented out old code
removed debug printf
* included prebuild test binary for Pi2
* Second attempt at the fix.
BEFORE:
If you have more physcial LEDs than defined in the "leds" "index" section of the config there is random junk added to the end of the strip.
WITH THIS FIX:
In the "device" section specify the number of physical leds with:
"leds" : 212,
If this is greater than the number of led indexes, additional LEDs are set to black
If this is smaller than the number of led indexes, it is ignored
* included test binary
* Clean exit if the device config is missing or a non-supported device type is specified
Former-commit-id: 8ae96188fa74d91b13a921e7d5faf6d6ac1c42ee
Small change to allow a random start hue for mood blobs - adds a bit of
spice instead of starting at the same color every time.
Former-commit-id: 2b5a0250b95ac5632661d3b8fce3c1567f5daaa3
* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
* Experimental changes to piblaster code to work how i think it should
It is now assumed that the PWM pins in groups of 3 correspond to RGB channels of the led.
"assignment" : "rgbrgbrgb",
Would result in:
//Channel number GPIO number Led channel
// 0 4 0 red
// 1 17 0 green
// 2 18 0 blue
// 4 27 1 red
// 5 21 1 green
// 6 22 1 blue
// 7 23 2 red
// 8 24 2 green
// 9 25 2 blue
* Ammend pwm channel mapping comments to match the code
* 1st cut of the new more flexible piblaster pin mapping support
it works but is still rough
* removed old "assignment" handling
- prints an error messaage if found and terminates
fixed the switchoff method
* removing iPins hard coded list of valid GPIO pins
* removed iPins array for switchOff function
* code cleanups
input validation
* Handle catching (and ignoring) SIGPIPE.
You can now kill and restart pi-blaster daemon and hyperiond will gracefully recover
* added a binary for testing
* Added sample config and my modified pi-blaster version to support more GPIOs
* moved hyperiond
* removed testing binaries
move sample configuration to the configs directory
* re enabled device config display
* removed sample configuration
Former-commit-id: 95e4d4ea2fb7cb5439e8cd597883a638da61a574
* Removed -HUP so the default -TERM signal is sent instead.
- hyperiond only listens for TERM and INT. HUP is often used to get an exe to reread its config
Changed pgrep to add '-x' so it wont partial match on the exe name.
- I have multiple instances with multiple hyperiond-instance1 names
- this ensures the service script only kills the right process
* reversing errant change to hyperion.systemd.sh
Former-commit-id: 7df14c9ab31bd808df7f286a8db89de3ac7d18bd
* Updated smoothing options for AtmoOrb, can now choose between Orb external or Hyperion's internal smoothing.
With skipSmoothingDif you can set the maximum allowed color difference before overriding / clearing Orb smoothing during faster color change like for instance color <-> black.
* Updated inline documentation.
* Fixed command type typo in AtmoOrb device.
* Corrected variable spelling in AtmoOrb device.
* Make smoothing also match equal values for AtmoOrb smoothing differential
Former-commit-id: 3eede43c2f76fa324f0144aeac0526b8125ad149
No functional changes, but
- files have been renamed
- the device name is now "file" not "test"
Former-commit-id: 3fbc03c3fe1d764654c1d28ebb80562ce6276ab1
2. Adds support for level shifters that invert the data
Config option - "invert" (integer)
if omitted, do not invert
if == 0, do not invert
if !=0, invert
Former-commit-id: fd5b2863a85b11ac3a8444d1e02822f852feb556
